Costway HW67581 User manual

www.costway.com
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Visit us: www.costway.com
Follow Costway
Please give us a chance to make it right and do better！
Contact our friendly customer service department for help first.
Replacements for missing or damaged parts will be shipped ASAP!
USER’S MANUAL
Electric Standing Desk
HW67581

Contact Us!
Do NOT return this item.
Contact our friendly customer service department for help first.
E-mail
US: [e-mail]
UK: [e-mail]
Before You StartBefore You Start
Please read all instructions carefully.
Retain instructions for future reference.
Separate and count all parts and hardware.
Read through each step carefully and follow the proper order.
We recommend that, where possible, all items are assembled near to the
area in which they will be placed in use, to avoid moving the product
unnecessarily once assembled.
Always place the product on a flat, steady and stable surface.
Keep all small parts and packaging materials for this product away from
babies and children as they potentially pose a serious choking hazard.
www.costway.com www.costway.com
IMPORTANT SAFEGUARDS
Read these instructions carefully and retain them for future use.
When using the product, basic safety precautions should always be
followed to reduce the risk of injury including the following:
●Unpack all hardware bags and components to ensure you have all
the parts.
●Use the tools included to assemble the desk, don’t use the incorrect
tools to assemble.
●Do not climb, stand or sit on the desk.
●Do not place objects on the desk when moving.
●Check to ensure all bolts, screws and brackets are tightened on a
regular basis.
●Do not place the table in a humid environment.
●Do not place heavy objects on the table when storing.
There is potential risk of personal injury not to follow the instructions
when in use.
02 03

www.costway.com www.costway.com
Parts List
A
C
E
G
I
B
D
F
H
J
Lift column*1
Base*2
Side bracket*2
Desk top*1
Power supply holder*1
Handset + Power supply
Power cord
M6 screws*24
LTapping screws*4
KM4 screws*1
MM10 screws*8
Lift column*1
Frame*2
Motor Rod*1
5# wrench*1
6# wrench*1
cross screwdriver*1
G1 G2 H1H2
J K L M I 1I 2I 3
D3
D2
D1
H3
H
3
G
2
I1
L
Step 2:
Assemble the 2 sets of beam components as shown in the figure
before use;
Note:1. Pay attention to the card slot direction.
2. The Jimmy screws at the bottom of D1 and D3 cannot be tightened.
Pay attention to
the card slot direction
D
3
D
2
D
1
D
1
D
2
D
3
Assembly steps
Step 1:
1.1 The hand controller is fastened to the table with self-tapping
screws using the supplied screwdriver .
1.2 After installing the power supply holder, set aside.
H
3
G2
04 05

www.costway.com www.costway.com
Step 3:
Fixing lift column and lift column to the table leg with M10
screws using the supplied spanner .
ABM
H
2
Step 4:
4.1 Assembling frame tightened with M6 screws using the supplied
spanner .
4.2 Then install the two side bracket with M6 screws using the
supplied spanner .
H
1
H
1
H
2
M
C
A
B
prohibited removal
H
1JE
J
Step 5:
5.1 Lay the table board flat and put the table shelf on it.
5.2 Stretch the table frame to both sides. Align the screw holes and
lock them with M6 screws using the supplied spanner .
5.3 Fasten the socket set screws on the middle beam.
H
1
J
Socket set
screws
Same side
J
H
1
06 07

www.costway.com www.costway.com
Step 6:
6.1 As shown in Figure 1, insert the hexagonal bar into the table leg B
until the buckle is not visible.
6.2 Assemble the other end of the connecting rod to the table leg A
and screw on the handle. The handle does not need to be tightened.
Note: As shown in Figure 2 below, it needs to be aligned with the card
slot.
6.3 Pull the connecting rod with the handle to the bottom end of the
table leg A in the direction of the arrow as follows.
6.4 Tighten the handle and install the M4 screws using the supplied
screwdriver .
6.5 Conect the power cord and motor of the power supply handest as
shown in the figure.
H
3
K
H
3
K
I
1
I
2
I
3
Tightened
On the card slot
1
2
3
Operational instructions
5. Protection and alarm
1.Block Protection: Display "E02."
2.Overheating protection: Display "Hot ." Continuous operating may initiate this protection
and should be recharged or waited for at least 18 minutes before use.
3.Motor abnormal protection: Display "E10." Should be powered off, re-check and ensure that
the connection of the motor to the controller is reliable and then reconnect.
4.Overload protection: Display "E20." This alarm should be removed from the desk top when
it’s operating up; if this alarm occurs when it’s operating down, cut off the power and the
heavy objects should be removed, and the power should be re-charged.
5.Under-voltage protection: Display "E31." Should be powered off, recheck and make sure the
connection between the power supply and the handset is reliable, then connect the power.
6.Over-voltage protection: Display "E32." Should be powered off, recheck and make sure the
connection between the power supply and the handset is reliable, then connect the power.
1. Lift Column
Press the button or button to control the lift column up or down Press the button to control
up of the lifting column, you can see the height (displayed number) on the screen; press the
button to control the down of the lifting column, you can see the height (displayed number) on
the screen.
2. Set memory height
Press( ) button for 2 seconds, set the current height to the memory height, When flashing
display "H1~H4"for 2 seconds, and then display the real-time height after 2 seconds.
3. Recall memory height
Press the number button ( ) can recall its corresponding height, lift column will automatically
run to the right position.
4. Stroke reset
"E10、E20" alarm state or running to the lowest height position, press the button 3 seconds,
after the display ( Reset) is released, the lifting column starts to run down to the bottom of
the frame and rebound to a certain height, the reset is completed to display the lowest height.
During the movement, a vibrating, colliding or tilting desktop will sound an alarm and stop the
movement immediately. After the automatic release, it will move in the reverse direction to set the
distance, you can press any key to stop and release during the reverse operation. Check and make
sure that the desktop will not vibrate significantly, hit obstacles or re-tilt during operation.
08 09

Welcome to visit our website and purchase our quality products!
We would like to extend our hearelt thanks to
all of our customers for taking me to assemble
this product and giving us valuable feedbacks.
With your inspiring rating, COSTWAY will be more consistent to offer you
EASY SHOPPING EXPERIENCE, GOOD PRODUCTS and EFFICIENT SERVICE!
US office: Fontana, California
UK office: Ipswich
www.costway.com
Reward Points
Exclusive Customer Service
Personalized Recommendaons
Permanent Shopping Cart
Order History
www.costway.com
10