Tennsco RXHS-962484 Instruction Manual

ASSEMBLY INSTRUCTIONS & PARTS MANUAL
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE
PK-2871018
Models: RXHS-962484, RXHS-962496,
Heavy-Duty Reinforced High Capacity Shelving
RXHS-963684, RXHS-963696
Extra shelves are also available (RXHS-wwdd).
Tennsco LLC. , Dickson, TN 37056-1888 • [phone]
GENERAL SAFETY INFORMATION
Some parts may have sharp edges. CARE must be taken when handling various pieces to avoid injury.
For safety, wear a pair of work gloves when assembling or performing any maintenance on the unit.
LIMITED WARRANTY
Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment, hereunder. This warranty shall not apply in
the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modication or repair by persons not authorized by Seller, where goods are damaged during
shipment, or where the date stamps on the goods have been defaced, modied or removed. UNLESS CONSIDERED UNENFORCEABLE OR UNLAWFUL UNDER APPLICABLE LAW:
a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXCLUDED:
b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT OF THE GOODS AT SELLER’S OPTION, AND SHALL IN NO
EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.
NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers place of business or require Buyer to return the
goods to Seller for inspection on Seller’s premises. Transportation charges covering returned goods will be borne by Seller only if such goods are proven to be defective, are covered by this warranty
and are returned within the warranty period stated above.
LOAD CAPACITIES
PER SHELF LEVEL*
96w x 24d
96w x 36d
2600 lbs.
2600 lbs.
UNIT SIZE WT. CAPACITY
*Total Unit Capacity not to exceed 13,000 lbs.

ASSEMBLY OF HEAVY-DUTY HIGH CAPACITY SHELVING
Two people are recommended for assembly. Approximate assembly time: 35-45 minutes per section.
The reference numbers used throughout this sheet refer to the illustration on the back cover.
This is to help you to identify the various parts as they are mentioned.
4. Lay the bottom steel decking (Ref. No. 6) on the shelf supports so that
the front and back edges overlap the front and back shelf supports.
1. With help from an associate, or using a wall for support,
create a unit end by connecting two SUR uprights together
(Ref. No. 1) with two front-to-back end shelf supports (Ref.
No. 2), one at the top and one at the bottom. Be sure the
supports are fully seated in the slots. Repeat to construct a
second unit end.
2. Next, connect the two unit ends with two LRA left-to-right
shelf supports (Ref. No. 3) at the bottom and one LRC left-
to-right shelf support (Ref. No. 4) at the top, temporarily
leaving off one of the top left-to-right supports.
NOTE: The two LRA supports at the bottom have no return ange
on the bottom edge, while the LRC support have a return ange
at both the top and bottom.
3. Attach three front-to-back center shelf supports (Ref. No. 5) by
inserting the deck support keyhole slots over the rivets on the
supports and tapping them rmly into place.
IMPORTANT! All shelf
supports should be
inserted with the
return flange on top,
as shown at right.
(This flange is what the
shelves will rest upon)
NOTE: Inset is shown
from opposite side.
NOTE: One top
support is not inserted
until step 8.
LRA (bottom level only)
One return flange on top.
LRC (all other levels)
Two return flanges.

NOTE: Bolts are not needed to secure the deck supports on
the bottom shelf because it rests on the oor. All other levels
require these bolts to achieve maximum load capcities.
NOTE: Every fourth slot in the uprights has a at top to
help visually align the supports.
5. Attach shelf supports at the next desired shelf level.
Once the shelf supports are in place, attach three
front-to-back center supports as you did in step 3.
Lower the steel decking into place, as described in step 4.
NOTE: Be sure to bolt both the front
and rear of each shelf. This requires
six bolts per shelf.
7. Attach the remaining shelf supports and decking at the
desired shelf levels, completing one level at a time.
NOTE: Once all but the top shelf are in place, attach the
remaining left-to-right shelf support at the top level.
8. After attaching the top shelf and securing it with six
sets of bolts, your die rack unit is fully assembled and
ready for use.
6. Once the decking is in place, secure it to the shelf supports
with six sets of 1/4-20 x 5/8bolts and nuts (Ref. No. 6). Do
this by placing one bolt through each hole in the front and
rear of the shelf, making sure the bolt goes through the shelf
and shelf supports as shown below. Tighten securely.

REPLACEMENT PARTS
Steel Decking
(Ref. No. 6)
Front-to-Back Center
Shelf Support
(Ref. No. 5)
Front-to-Back
End Shelf Support
(Ref. No. 2)
Bolts and Nuts
1/4-20 x 5/8”
(Ref. No. 7)
Heavy
Upright Post
(Ref. No. 1)
Left-to-Right (LRA)
Shelf Support
(Ref. No. 3)
Tennsco makes every effort to ensure that all units ship complete with all parts and arrive undamaged.
However, should your unit contain missing or damaged parts, please contact your purchase location.
NOTE: Additional hardware may be included for replacement purposes.
Left-to-Right (LRC)
Shelf Support
(Ref. No. 4)
REF. NO. DESCRIPTION
1 Heavy Upright Post 4 SUR-84 SUR-84 SUR-96 SUR-96
2 Front-to-Back End Shelf Support 10 LRA-24 LRA-36G LRA-24 LRA-36G
3 LRA Left-to-Right Shelf Support 2 LRA-96 LRA-96 LRA-96 LRA-96
4 LRC Left-to-Right Shelf Support 8 LRC-96 LRC-96 LRC-96 LRC-96
5 Front-to-Back Center Shelf Support 15 SDS-24 SDS-36 SDS-24 SDS-36
6 Steel Decking 5 ZS-9624 ZS-9636 ZS-9624 ZS-9636
7 1/4-20 x 5/8” Bolts and Nuts AVAILABLE LOCALLY
PART NUMBERS
RXHS-962484 RXHS-963684 RXHS-962496 RXHS-963696
QTY.
49B287