Courtyard Creations TCS19LA-WM User manual

FIGURE 1
Do not sit or stand on this table.
Do not discard any of the packaging until you have checked that you have all the parts and pack of fittings.
Keep children away during assembly. This item contains small parts which can be swallowed by children.
Children should always be under direct adult supervision while using the product.
Retain the assembly instructions for future reference.
Please quote following FQC NO. when contacting service center.
SERVICE CENTER TOLL FREE NO.
TEL: [phone]
FAX: [phone]
Step 1:
Place the table top (#1) onto a non-abrasive surface, such as
a carpet, with the underside facing upwards. Fasten the legs
(#2) to the table top (#1) rim by using bolts (#5). Keep the
bolts loose. See Figure 1.
HEX.KEY WRENCH 6MM
BOLT CAP M6
WASHER d6.5*D13*1.0
BOLT CAP M6
BOLT M6*16
BOLT M6*35
TILE
LEG
SUPPORT
TABLE TOP
17KAA0201----Y4
1800337006
17FA05040301-Y4
1800337002
17C01A0706002Y4
17C02A0712003Y4
13C??B30008001
62TCS19LAI101
TCS19LA-CS02
6
6
4
4
4
1
TCS19LA-CS01
4
10
9
8
7
6
5
2
4
2
1
3
2
1
Q’TYPARTMATERIAL CODE
PARTS LIST
PART
NO. Q’TYPARTMATERIAL CODE
PART
NO.
TCS19LA-WM
ASSEMBLY INSTRUCTIONS
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE
INTENDED FOR RESIDENTIAL USE ONLY.
PAGE 1 OF 2 COURTYARD CREATIONS INC.
!
!
!
!
!
STOP DON’T RETURN TO STORE!
5
1
35
2
2
8
Attention:
Make sure that each bolt needed for all steps match the
corresponding figure to ensure proper assembly.
#5 BOLT M6*35
NOTE:
The tiles can be easily broken, please be careful when
removing them. Do not throw away the residual tiles, retain
them for future use.

35
#5 BOLT M6*35
#6 BOLT M6*16
FIGURE 4 FULL ASSEMBLY
FIGURE 2 FIGURE 3
PAGE 2 OF 2
Step 5:
See Full Assembly.
Step 2:
Fasten the supports (#3) to the legs (#2) by using the bolts
(#6) and washers (#7). Keep the bolts loose. See Figure 2.
Step 3:
Fasten the supports (#3) to the table top (#1) by using the
bolts (#5). See Figure 3.
Missing A Part?
No Need To Go Back To
TheStore!
The store where you made your purchase
does not stock parts for this item
if you need parts,
whether they are missing or damaged.
Call Toll Free
TEL: [phone]
FAX: [phone]
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
PLEASE READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ASSEMBLY
PLEASE SEPARATE AND IDENTIFY ALL PARTS, MAKING SURE THAT YOU
HAVE ALL OF THEPARTSLISTED.
SHOULD YOU NOTLOCATE ALL OF THE ABOVE PARTS, PLEASE INSPECTALL
PACKING MATERIAL FOR ANY SMALL PARTSTHAT MAYHAVEBECOME
SEPARATED IN SHIPMENT.
SHOULDYOU EXPERIENCEANYDIFFICULTYDURING ASSEMBLYOR IF ANY
PARTIS MISSING OR DAMAGED,PLEASE CALL THE HELP LINE 1-877-539-7436
BEFORERETURNING THEITEM TO THESTORE.
PLEASE PROVIDE THEFOLLOWING INFORMATION:
1-MODEL NUMBER OF THEPRODUCT.
2-PARTNUMBER AND MATERIAL CODE OF THE PARTFROM THE PARTS LIST
SHOWN ON ASSEMBLY INSTRUCTIONS.
MOST PROBLEMSCAN BERESOLVED WITHOUT RETURNING THIS PRODUCT
TO THERETAILER.
The store where you made your purchase
does not stock parts for this item
if you need parts,
whether they are missing or damaged.
STOP!
MissingAPart?
No Need To Go Back To
The Store
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
Call Toll Free
TEL: [phone]
FAX: [phone]
STOP DON’T RETURN TO STORE!
Cleaning and Maintenance
• Wash frame parts with mild soap and water, rinse thoroughly, and dry frame completely. Do not use bleach, acid, or other
solvents on the frame parts.
• Please inspect and tighten all bolts and fasteners on a regular basis to ensure proper performance and safety of your table.
• When moving the table, do not drag.
• We recommend the use of furniture covers when not in use.
• In order to prolong the life and beauty of your table, we recommend it be stored in a dry and protected area during off
season periods.
4
9672
3
16
3
2
NOTE:
1. The arrows mark on the supports(#3) must coincide with
Figure 2 to ensure proper assembly.
2. Make sure that the tabs on the supports (#3) must be
facing inside to ensure proper assembly.
NOTE:
If the EVA foams on the table top are missing, replace
them with the EVA foams supplied in the hardware kit.
See Illustration A.
Step 4:
Turn the table to its upright position and put the tiles (#4)
onto the table top (#1). See Figure 4.
Tab 3
1
8
5
3
Make sure that all of the bolts have been tightened
completely and then cover them with bolt caps (#8 and #9).