Courtyard Creations TGS27NW-WM User manual

PAGE 1 OF 2
STOP DON’T RETURN TO STORE! COURTYARD CREATIONS INC.
FIGURE 1
Do not sit or stand on this table.
Do not discard any of the packaging until you have checked that you have all the parts and
pack of fittings.
Keep children away during assembly. This item contains small parts which can be
swallowed by children. Children should always be under direct adult supervision while
using the product.
Retain the assembly instructions for future reference.
Please quote following FQC NO. when contacting service center.
SERVICE CENTER TOLL FREE NO.
TEL: [phone]
FAX: [phone]
Step 1:
Place the table top (#1) onto a non-abrasive
surface, such as a carpet, with its underside
facing up. Insert the legs (#2) into the plastic
holders on the table top (#1) rim. Fasten them
together by using screws (#4). See Figure 1.
You will need the following tools:
- Phillips Screwdriver (Not Included)
- Hex. Key Wrench (See Part #8)
HEX.KEY WRENCH 6MM
BOLT CAP M6
WASHER d6.5*D13*1.0
BOLT M6*20
SCREW ST4.2*12
CENTER
CONNECTOR
LEG
TABLE TOP
17KAA0201----Y4
1800337002
17FA05040301-Y4
17C01A0708002Y4
17C17A0403001Y4
62TGS27NWY101
TGS27NW-CS02
TGS27NW-CS01
1
8
8
8
8
7
6
5
4
1
4
1
4
3
Q’TY Q’TY
1
2
PART PART MATERIAL CODE MATERIAL CODE
PART
NO. PART
NO.
PARTS LIST
TGS27NW-WM
ASSEMBLY INSTRUCTIONS
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE
INTENDED FOR RESIDENTIAL USE ONLY.
222
2
1
4
!
!
!
!
!

Cleaning and Maintenance
•Wash frame parts with mild soap and water,
rinse thoroughly, and dry frame completely.
Do not use bleach, acid, or other solvents on
the frame parts.
•Wash glass with mild soap and water, rinse
thoroughly, and dry glass completely. Please
inspect and tighten all bolts and fasteners on a
regular basis to ensure proper performance and
safety of your table.
•When moving the table, do not drag.
•We recommend the use of furniture covers when
not in use.
• In order to prolong the life and beauty of your
table, we recommend it be stored in a dry and
protected area during off season periods.
FIGURE 3
FIGURE 2
Step 2:
Fasten the center connector (#3) to the middle
of the legs (#2) by using bolts (#5) and washers
(#6). See Figure 2.
Make sure that all of the bolts have been
tightened completely, and then cover them with
bolt caps (#7).
Step 3:
Turn the table to its upright position. See Figure 3.
PAGE 2 OF 2
Missing A Part?
No Need To Go Back To
TheStore!
The store where you made your purchase
does not stock parts for this item
if you need parts,
whether they are missing or damaged.
Call Toll Free
TEL: [phone]
FAX: [phone]
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
PLEASE READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ASSEMBLY
PLEASE SEPARATE AND IDENTIFY ALL PARTS, MAKING SURE THAT YOU
HAVE ALL OF THEPARTSLISTED.
SHOULD YOU NOTLOCATE ALL OF THE ABOVE PARTS, PLEASE INSPECTALL
PACKING MATERIAL FOR ANYSMALL PARTSTHAT MAYHAVEBECOME
SEPARATED IN SHIPMENT.
SHOULD YOU EXPERIENCEANY DIFFICULTY DURING ASSEMBLYOR IF ANY
PARTIS MISSING OR DAMAGED,PLEASE CALL THE HELP LINE 1-877-539-7436
BEFORERETURNING THEITEM TO THESTORE.
PLEASE PROVIDE THEFOLLOWING INFORMATION:
1-MODEL NUMBER OF THEPRODUCT.
2-PARTNUMBER AND MATERIAL CODE OF THE PARTFROM THE PARTS LIST
SHOWN ON ASSEMBLY INSTRUCTIONS.
MOST PROBLEMSCAN BERESOLVED WITHOUT RETURNING THIS PRODUCT
TO THERETAILER.
The store where you made your purchase
does not stock parts for this item
if you need parts,
whether they are missing or damaged.
STOP!
MissingAPart?
No Need To Go Back To
The Store
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
Call Toll Free
TEL: [phone]
FAX: [phone]
STOP DON’T RETURN TO STORE!
2
22
3
7
7
5
5
6
6
2