Courtyard Creations TGS64DP-WM User manual

ASSEMBLY INSTRUCTIONS
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE
INTENDED FOR RESIDENTIAL USE ONLY.
TGS64DP-WM
PAGE 1 OF 2 COURTYARD CREATIONS INC.
PARTS LIST
PART
NO. MATERIAL CODE PART Q’TY PART NO. MATERIAL CODE PART Q’TY
11
2
3
4
5
7
6
8
9
10
4
2
4
12
12
1
8
1
6
TGS64DP-CS05-1
TGS64DP-CS04-1
TGS64DP-CS04-2
62TGS65DPY101
17C17A0403001Y4
17C01A0706002Y4
17C01A0709002Y4
17FA05040301-Y4
18000337002
17KAA0201----Y4
TABLE TOP
LEG
SUPPORT
CENTER
CONNECTOR WITH RING
SCREW ST4.2*12
BOLT M6*16
BOLT M6*25
WASHER d6.5*D13*1.0
BOLT CAP M6
HEX.KEY WRENCH 6MM
FIGURE 1
You will need the following tools:
- Phillips Screwdriver (Not Included)
- Hex. Key Wrench (See Part #10)
Step 1:
Place the table top (#1) onto a non-abrasive surface,
such as a carpet, with its underside facing upwards.
Insert the legs (#2) and supports (#3) into the plastic
holders on the table top (#1) rim. Fasten them together
by using screws (#5). See Figure 1.
Attention:
Make sure that each bolt needed for all steps matches
the corresponding figure to ensure proper assembly.
1
22
2
2
3
3
STOP DON’T RETURN TO STORE!
SERVICE CENTER TOLL FREE NO.
TEL: [phone]
FAX: [phone]
5
Use the correct bolts as indicated. Do not tighten any of the bolts until is completely assembled.
Do not sit or stand on this table.
A weighted umbrella base must be used when using an umbrella with this table.
Do not discard of any of the packaging until you have checked that you have all of the parts and
fittings required.
Keep children away during assembly. This item contains small parts that can be swallowed by
children. Children should always be under direct adult supervision while using this product.
Retain these assembly instructions for future reference.
Quote the following FQC NO. when contacting the service center.
!
!
!
!
!
!
!

STOP DON’T RETURN TO STORE!
PAGE 2 OF 2
FIGURE 2 FIGURE 3
FIGURE 4
Step 2:
Fasten the center connector with ring (#4) to the middle
of the legs (#2) by using bolts (#6) and washers (#8).
Keep the bolts loose. See Figure 2.
Step 3:
Fasten the center connector with ring (#4) to the
supports (#3) by using bolts (#7) and washers (#8).
Make sure that all of the bolts have been tightened
completely and cover them with bolt caps (#9).
See Figure 3.
Step 4:
Turn the table to its upright position. See Figure 4.
Cleaning and Maintenance
•Wash frame parts with mild soap and water, rinse
thoroughly, and dry completely. Do not use bleach,
acid, or other solvents on the frame parts.
•Wash glass with mild soap and water, rinse thoroughly,
and dry completely.
•Inspect and tighten all bolts and fasteners on a regular
basis to ensure the proper performance and safety of
your table.
•When moving the table, remove the umbrella and lift.
Do not drag this table.
•We recommend the use of furniture covers when not
in use.
•In order to prolong the life and beauty of your table,
we recommend that it be stored in a dry and protected
area during off season periods.
•Tempered glass has been used for increased strength
and safety of your table. However, during windy
conditions the umbrella should be lowered and/or
removed.
Note:
To use an umbrella with this table, remove the plastic
center plug and put the umbrella pole through the table
top and center connector ring.
#7 BOLT M6*25
25
#6 BOLT M6*16
16
6
68
8
9
9
2
2
2
2
43
3
4
7
7
8
8
9
9
The store where you made your purchase
does not stock parts for this item.
If you need parts,
whether they are missing or damaged,
STOP!
MissingAPart?
No Need To Go Back To
The Store
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
Call Toll Free:
TEL: [phone]
FAX: [phone]
READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ASSEMBLY
SEPARATE AND IDENTIFY ALL PARTS, MAKING SURE THAT YOU
HAVE ALL OF THEPARTSLISTED.
IF YOU DO NOTLOCATE ALL OF THE PARTS LISTED, INSPECT THE
PACKING MATERIAL FOR SMALL PARTSTHAT MAYHAVEBECOME
SEPARATED DURING SHIPMENT.
IF YOU EXPERIENCEANYDIFFICULTY DURING ASSEMBLYOR IF ANY
PARTS ARE MISSING OR DAMAGED,CALL THE HELP LINE AT
1-877-539-7436 BEFORERETURNING THIS ITEM TO THESTORE.
PROVIDE THEFOLLOWING INFORMATION WHEN CALLING:
1-MODEL NUMBER OF THEPRODUCT.
2-PARTNUMBER AND MATERIAL CODE OF THE PARTFROM THE PARTS
LIST.
MOST PROBLEMSCAN BERESOLVED WITHOUT RETURNING THIS
PRODUCT TO THERETAILER.