Courtyard Creations XLS005W-WM User manual

ASSEMBLY INSTRUCTIONS
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE
INTENDED FOR RESIDENTIAL USE ONLY.
XLS005W-WM
Weight limit for each shelf is 35kg or 89lbs.
Use the correct bolts as indicated. Do not tighten any of the bolts until is completely assembled.
Do not discard of any of the packaging until you have checked that you have all of the parts and fittings
required.
Keep children away during assembly. This item contains small parts that can be swallowed by children.
Children should always be under direct adult supervision while using this product.
Retain these assembly instructions for future reference.
Quote the following FQC NO. when contacting the service center.
SERVICE CENTER TOLL FREE NO.
TEL: [phone]
FAX: [phone]
PAGE 1 OF 3 COURTYARD CREATIONS INC.
!
!
!
!
!
!
STOP DON’T RETURN TO STORE!
PARTS LIST
PART
NO. MATERIAL CODE PART Q’TY
1 1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
1
2
4
6
6
1
1
1
4
1
1
1
1
XLS005W-CS01
XLS005W-CS02
XLS005W-CS03
XLS005W-CS04
47LA66145
47LA66144
47LA66142
62XLS005WI101
17C17A0403001Y4
17C33A0710001Y4
17C33A0706001Y4
17FA05040301-Y4
18000337004
17KAA0101----Y4
RIGHT SUPPORT FRAME
LEFT SUPPORT FRAME
RIGHT LEG
LEFT LEG
MESH FRAME A
MESH FRAME B
MESH FRAME C
MESH FRAME D
UPPER STORY BACK
SCREW ST4.2*12
WASHER d6.5*D13*1.0
BOLT M6*30
BOLT M6*16
BOLT CAP
HEX.KEY WRENCH 4MM
Attention:
Make sure that each bolt needed for all steps matches the
corresponding figure to ensure proper assembly.
FIGURE 1
10
1
Step 1:
Place the right support frame (#1) onto a non-abrasive surface,
sush as a carpet. Insert the right leg (#3) to the right support
frame (#1) by using screw (#10). Repeat the same procedure
for the left support frame (#2) and the left leg (#4).
See Figure 1.
1
47LA66143
R
3R
You will need the following tools:
- Phillips Screwdriver (Not Included)
- Hex.Key Wrench (See Part #15)
Note:
The label that are marked “1, 2, 3, 4” on the support frames
and the legs should coincide with Figure 1 & 2 to ensure proper
assembly.

PAGE 2 OF 3
STOP DON’T RETURN TO STORE!
FIGURE 2 FIGURE 3
Step 3:
Put the mesh frame B (#6) and mesh frame C (#7) into the
holders located on the legs (#3, #4).
See Figure 3.
Cleaning and Maintenance
• Wash frame parts with mild soap and water, rinse thoroughly,
and dry completely. Do not use bleach, acid, or other solvents
on the frame parts.
•
Inspect and tighten all bolts and fasteners on a regular basis
to ensure the proper performance and safety of your stand.
•When moving the stand, lift. Do not drag this stand.
•
We recommend the use of furniture covers when not in use.
•In order to prolong the life and beauty of your stand, we
recommend that it be stored in a dry and protected area
during off season periods.
Step 4:
Fasten the upper story back (#9) to the support frames (#1, #2)
by using bolts (#12) and washers (#13). See Figure 4.
Step 5:
Put the mesh frame D (#8) into the holders located on the
supports frame (#1, #2).
Make sure that all of the bolts have
been tightened completely and cover them with bolt caps (#14).
See Figure 5.
Step 6:
See Full Assembly.
8
122
2
1
1
FULL ASSEMBLY
FIGURE 5
4
5
A
6
7
3
4
2
1
11
14
13
L
3R
B
C
D
Step 2:
Put the mesh frame A (#5) into the holders located on the
legs (#3, #4) by using bolts (#11) and washers (#13). Keep the
bolts loose. See Figure 2.
FIGURE 4
14
1
9
12
13
2

PAGE 3 OF 3
The store where you made your purchase
does not stock parts for this item.
If you need parts,
whether they are missing or damaged,
STOP!
Missing A Part?
No Need To Go Back To
The Store
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
Call Toll Free:
TEL: [phone]
FAX: [phone]
READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ASSEMBLY
SEPARATE AND IDENTIFY ALL PARTS, MAKING SURE THAT YOU
HAVE ALL OF THEPARTSLISTED.
IF YOU DO NOTLOCATE ALL OF THE PARTS LISTED, INSPECT THE
PACKING MATERIAL FOR SMALL PARTSTHAT MAYHAVEBECOME
SEPARATED DURING SHIPMENT.
IF YOU EXPERIENCEANY DIFFICULTY DURING ASSEMBLYOR IF ANY
PARTS ARE MISSING OR DAMAGED,CALL THE HELP LINE AT
1-877-539-7436 BEFORERETURNING THIS ITEM TO THE STORE.
PROVIDE THEFOLLOWING INFORMATION WHEN CALLING:
1-MODEL NUMBER OF THEPRODUCT.
2-PARTNUMBER AND MATERIAL CODE OF THE PARTFROM THE PARTS
LIST.
MOST PROBLEMS CAN BERESOLVED WITHOUT RETURNING THIS
PRODUCT TO THERETAILER.
STOP DON’T RETURN TO STORE!