Courtyard Creations TGS40NW User manual

FIGURE 1
Use the correct bolts as indicated. Do not tighten any of the bolts until is completely assembled.
Do not sit or stand on this table.
Do not discard any of the packaging until you have checked that you have all the parts and pack
of fittings.
Keep children away during assembly. This item contains small parts which can be swallowed by
children. Children should always be under direct adult supervision while using the product.
Retain the assembly instructions for future reference.
Quote the following FQC NO. when contacting the service center.
Step 1:
Place the table top (#1) onto a non-abrasive
surface, such as a carpet, with its underside
facing upward. Insert the legs (#2) into the plastic
holders on the underside table top (#1) rim. Fasten
them together by using screws (#4). See Figure 1.
You will need the following tools:
- Phillips Screwdriver (Not Included)
- Hex. Key Wrench (See Parts #8)
HEX.KEY WRENCH 6MM
BOLT CAP M6
WASHER d6.5*D13*1.0
BOLT M6*16
SCREW ST4.2*12
CENTER CONNECTOR
LEG
TABLE TOP
17KAA0201----Y4
18000337002
17C01A0706002Y4
17FA05040301-Y4
17C17A0403001Y4
62TGS40NWY101
TGS40NW-CS02
8
8
8
1
TGS40NW-CS01
8
7
6
4
5
1
4
1
4
3
2
1
Q’TY
PARTMATERIAL CODE
PART
NO.
Q’TY
PARTMATERIAL CODE
PARTS LIST
PART
NO.
TGS40NW-WM
ASSEMBLY INSTRUCTIONS
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE
INTENDED FOR RESIDENTIAL USE ONLY.
COURTYARD CREATIONS INC.
!
!
!
!
!
!
4
1
2
2
2
2
PAGE 1 OF 2
STOP DON’T RETURN TO STORE!
SERVICE CENTER TOLL FREE NO.
TEL: [phone]
FAX: [phone]

Cleaning and Maintenance
•Wash frame parts with mild soap and water, rinse thoroughly, and dry completely. Do not use bleach,
acid, or other solvents on the frame parts.
•Wash glass with mild soap and water, rinse thoroughly, and dry completely.
•Inspect and tighten all bolts and fasteners on a regular basis to ensure proper performance and
safety of your table.
• When moving the table, lift. Do not drag this table.
• We recommend the use of furniture covers when not in use.
• In order to prolong the life and beauty of your table, we recommend that it be stored in a dry and
protected area during off season periods.
FIGURE 3FIGURE 2
PAGE 2 OF 2
Step 3:
Turn the table to its upright position. See Figure 3.
Step 2:
Fasten the center connector (#3) to the middle of
the legs (#2) by using bolts (#5) and washers (#6).
Make sure that all of the bolts have been tightened
completely and cover them with bolt caps (#7).
See Figure 2.
6
5
7
2
2
3
2
2
STOP DON’T RETURN TO STORE!
The store where you made your purchase
does not stock parts for this item.
If you need parts,
whether they are missing or damaged,
STOP!
Missing A Part?
No Need To Go Back To
The Store
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
Call Toll Free:
TEL: [phone]
FAX: [phone]
READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ASSEMBLY
SEPARATE AND IDENTIFY ALL PARTS, MAKING SURE THAT YOU
HAVE ALL OF THEPARTSLISTED.
IF YOU DO NOTLOCATE ALL OF THE PARTS LISTED, INSPECT THE
PACKING MATERIAL FOR SMALL PARTSTHAT MAYHAVEBECOME
SEPARATED DURING SHIPMENT.
IF YOU EXPERIENCEANY DIFFICULTY DURING ASSEMBLYOR IF ANY
PARTS ARE MISSING OR DAMAGED,CALL THE HELP LINE AT
1-877-539-7436 BEFORERETURNING THIS ITEM TO THE STORE.
PROVIDE THEFOLLOWING INFORMATION WHEN CALLING:
1-MODEL NUMBER OF THEPRODUCT.
2-PARTNUMBER AND MATERIAL CODE OF THE PARTFROM THE PARTS
LIST.
MOST PROBLEMS CAN BERESOLVED WITHOUT RETURNING THIS
PRODUCT TO THERETAILER.