COVANA LEGEND User manual

covana.com
LEGEND
Preparing the way
for your new Covana spa cover
Pre-Delivery
Guide
swim spa coverLEGEND

2
A new level
of luxury!
Easy access to
your swim spa with
protection against
the weather and
ultraviolet radiation
while providing you
with a luxurious vibe.
In this Pre-Delivery Guide:
Swim spa compatibility............................................................................. 3
Color options .......................................................................................... 5
Choosing the perfect location ................................................................... 6
Laying the right foundation....................................................................... 7
Electrical specifications ............................................................................. 8
Planning the delivery................................................................................ 9
Notes .................................................................................................... 11
Less effort, more comfort for a longer time:
A promise signed Covana.

3
Most rectangular swim spas with a flat surface (no protruding headrests) and the following features:
• Spa wall on both sides must be flat and parallel.
• The seal of the cover will have to be installed
on a flat surface of at least 1" wide, on the
acrylic of the spa. The minimum turn radius of
the seal is 4". Ensure the seal will be able to go
all around the spa while continuously touching
the cover.
Swim spa compatibility
Swim Spa
maximum length
legend
length 
146¾" 12 ft
158¾" 13 ft
170¾" 14 ft
182¾" 15 ft
194¾" 16 ft
206¾" 17 ft
218¾" 18 ft
230¾" 19 ft
241¾" 20 ft
1" min.
4" min.
Refer to the table below to choose the appropriate model according to the length of your swim spa.
If you don’t know which model to choose, or if you are unsure whether your swim spa will fit under the
cover or not, please contact Covana for the Technical Support department: 1-877-278-8010.

4
Swim spa compatibility (continued)
Depending on your swim spa height and its frame height, one or two types of bracket might be needed. Refer to
the tables below to see if it is the case.
The Legend cover must be installed at the same ground level as the swim spa.
a Bracket required 
48"
to 61" None
46½"
to 48" Dual side bracket
61"
to 62" Dual side bracket
B Bracket required 
<50" None
>50" Extended bracket
If your swim spa has two sections, similar to the swim spa illustrated below, the installation of two
escape hatches is mandatory.
Escape hatch Escape hatch
Swim Spa
SectionS
eScape hatch(eS)
required 
1 1
2 2

5
Color options
Mocha
Latte White
White
Slate
Platinum
For a slight extra on the price of the regular white pannel, this option allows you to better match the
color of your Covana with your environment. A little detail that can make a big difference.
Customize your cover by choosing between the following options:
(Actual colors may vary from images shown.)

6
• The Covana cover can be installed either indoors or outdoors.
• Away from flood zone, water downpours or debris falling.
• Wind speeds should not exceed 25 mph in the raised position.
• Operating area must be free from obstacles, i.e., branches or electrical power lines.
• Allow for safe access to the spa, free of obstacles or debris.
• Sunlight must not converge or be directly reflected on the cover such as the
reflection from a window.
• The surface must be clean and free of any vegetation (i.e., grass, branches,
roots) and mineral contaminants (i.e., rocks, dust, sand).
• The key switch must be permanently mounted and located 5 ft away from the spa
and 5 ft above the deck or ground level in a location where no water downpour
or debris could fall on it.
• The user must have a clear view of the cover when operating it (25-ft cable).
Choosing the perfect location
Operating area free from obstacles Sunlight must not converge or be reflected on the cover
Clean surface free of vegetation and mineral contaminants
Key switch located 5 ft away from the spa
Safe access to the spa
Away from flood zone or water downpours
Legend
Installation prep.
SCAN ME!

7
• A clean, flat and level surface such as a concrete slab is needed.
• The cover must be installed on the spa foundation. When not possible, a concrete pier or some cover support
dedicated slabs must be provided.
• The four jacks of the cover will have to be properly fastened to the spa frame.
• Allow for at least 24" of clearance for maintenance on the posts sides, and 18" on the other sides.
• The foundation must be able to support at least 1,000 lb.
• Any water accumulating around the cover will have to be drained.
Laying the right foundation
minimum BaSe Size
Contact Covana if the foundation is already in place and its dimensions are smaller than those illustrated below.

8
• All electrical work should be done by a certified electrician, otherwise the certification and warranty will be void.
• The cover must be installed in accordance with and comply with all applicable local codes and regulations.
• Wires and conduits should be sized according to local codes and regulations.
Electrical specifications
North American requirements
Voltage 115 V, 60 Hz (1 hot, 1 neutral, 1 ground)
GFCI 15 A single-pole GFCI (not included)
Current draw Max 3 A
North American requirements
Voltage 24 VDC System
Wall outlet voltage 115 VAC for charger
Battery 24 V DC, 12 Ah, AGM sealed lead-acid battery
Australian/European/New-Zealand requirements
Voltage 24 VDC System
Wall outlet voltage 230 VAC for charger
Battery 24 V DC, 12 Ah, AGM sealed lead-acid battery
ac operated model
The cover requires a dedicated single-phase 115 VAC (North America).
Battery operated model
The standard AC powered system can be replaced with the optional battery-powered version.
It comes with a set of two batteries and a solar panel to enhance their performance.
market model 
Australia/Europe/
New Zealand
Battery operated model with solar panel
Battery operated model without solar panel
North America AC operated model
Battery operated model with solar panel

9
The Legend cover will be delivered in a wooden crate. Take the time to sketch out a quick map from
the delivery point to the installation point for the delivery personnel. You can also disassemble the
unit from the crate at the delivery point and move the parts by hand.
Planning the delivery
Dimensions for reference only.

10
Planning the delivery (continued)
Measure the width of stairs and steps to get up and over
Use this simple checklist to plan the delivery route.
Are there railings in the way, and how wide apart are they
Measure to see if shrubs or trees are an obstacle
Ensure sidewalks are free of objects and clutter
Check the doghouse or shed to see available clearance
Check for uneven ground or slippery slopes
Measure for overhanging gutters or downspouts
Gate measurement for clearance
Recreational vehicles and cars in the driveway
 automobiles / recreational vehicules  trees / foliage / shrubs
 gutter / facia / soffit overhang  patio furniture / deck chairs
 electrical / gas meter equipment  fences or narrow gates
 doghouse / playhouse  gravel, rocks or wood piles
 stairs / steps / railings  adequate access to wood decks
 uneven ground  door openings (if applicable)
 slippery slope or path  sheds or built-in structures

11
Notes

Printed in Canada
247031 Rev 0
Your heaven
of relaxation
and privacy
The manufacturing
process and the
choice of materials
lend COVANA
products exceptional
quality, performance
and durability.
For more information, contact
Covana* or visit our Web site:
covana.com
[e-mail]
*COVANA is a member of Canimex Group,
committed to excellence since 1969.