Creality HALOT-ONE PLUS User manual

3D Printer User Manual
V1.0
HALOT-ONE PLUS
Create reality，achieve dreams
HALOT-ONE PLUS

Dear Consumers,
Thank you for choosing our products.For the best experience,please read the instructions before operating the Printer. Our
teams are always ready to render you the best services. Please contact us via the phone number or e-mail address provided
at the end when you encounter any problem with the Printer.
For a better experience in using our product, you can also access how to use the printer in the following ways:
View the accompanied instructions and videos in the U disk.
Visit our official website www.creality.com to find relevant software/hardware information,contact details and operation and
maintenance instructions.
Firmware/Software Downloads and Upgrades
The product has access to both LycheeSlicer and CHITUBOX. WIFI printing and access to the Creative Cloud are under development.
Download the firmware and HALOT BOX slicing software at: https://www.creality.com
Download the CHITUBOX slicing software at: https://www.chitubox.com
Download the LycheeSlicer slicing software at: https://lychee.mango3d.io
Slicing software supported：

NOTES
1
2
3
4
5
6
7
8
9
10
Do not use the printer any way other than described to avoid personal injury or property damage.
Do not place the printer near any heat source or flammable or explosive objects. We suggest placing it in a well-ventilated, low-dust environment.
Do not expose the printer to violent vibration or any unstable environment, as this may cause poor print quality.
Please use recommended resin in case damage to machine.
Do not use any other power cable except the one supplied. Always use a grounded three-prong power outlet.
Please do not open the plastic cover during usage, otherwise the printing will be interrupted.
Do not wear cotton gloves when operating the printer. Such cloths may become tangled in the printers moving parts leading to burns, possible bodily injury, or printer damage.
Please wait after the print is finished. please wear gloves to take out the print tools.
Children under 10 years should not use the printer without supervision.
11
12
Tips Do not plug or unplug the power cord when power on.
Clean the printer frequently. Always turn the power off when cleaning, and wipe with a dry cloth to remove dust, adhered printing plastics or any other material off the frame,
guide rails, or wheels. Use glass cleaner or isopropyl alcohol to clean the print surface.
Users should comply with the laws and regulations of the corresponding countries and regions where the equipment is located (used), abide by professional ethics, pay attention to safety
obligations, and strictly prohibit the use of our products or equipment for any illegal purposes. Creality will not be responsible for any violators' legal liability under any.

Contents
Equipment Introduction 01-01
Equipment Parameters 02-02
Parts List 03-03
04-05
11-16
06-10
17-17
18-18
Assemble the 3D Printer
Use the 3D Printer
Troubleshooting
Print Method
Wiring Connection
19-19
FCC Statement
20-20
IC Cautiont

01
1. Equipment Introduction
Hexalobular socket screw
Leveling screw
Platform plate
Resin vat
Air filter
Power receptacle
Power switch
USB port
Touch screen
Limit sensor
9
7
8
10
11
Resin vat fixing screw

02
Model Name HALOT-ONE PLUS
172*102*160mm (length*width * height)
4320*2560
0.04mm
1-4S/ layer
0.01-0.2mm
236*243*418 mm
310*300*530mm
8.6KG
USB Disk，Creality Cloud App, Creality Cloud Online, WiFi Print
中文(简/繁)/ English/ Español/ Deutsche/ Français/ Pусский/ Português/ Italiano/ Türk/Nederlands/Polskie/日本語/한국어
Win7/Win8/Win 10 64bit, Mac system(32-bit is not supported)
Common rigid photosensitive ,Standard resin ,High hardness ,High toughness ,Dental model resin
Integral Light Source(wavelength 405nm)
100-240V~,50/60Hz
100WRated Power
Machine Size
Package Size
Net Weight
Compatible Resin
Machine Language
Gross Weight
Print Method
Slicing Software Operation System
Build Size
XY Axis Resolution
Touch Screen
Light Source Type
Rated Voltage
XY Axis Accuracy
Print Speed
Layer Thickness
Basic Parameters
5 inch touch screen
6.8KG
2. Equipment parameters

03
3. Parts Content List
Tool list
Print platform x 1 Resin vat x 1 3D printer x 1
Tips: the above accessories are for reference only lease refer to the physical accessories!
4
3
U disk x 1 Paper funnel x 2
Power cable x 1
Release film x 1
6
5Metal blade x 1
Screwdrivers x 1set
7Plastic blade x 1 8Calibration card x 1
9Tray fixing screw x 2

04
4. Assemble the 3D Printer
Take out the resin vovt align the two tray fixing screws with the corresponding holes and tighten them to fix. (as the picture shows)
Resin vat x 1
9
10
10
Tray fixing screw x 2

05
4. Assemble the 3D Printer
Machine body x 1
Plastic Upper cover x 1
Note: put the upper cover on the machine body and the installation is completed.

06
5. Interface Information
Note: Check whether the light source is normal The UI interfaceis only for reference , the actual UI.
Settings

07
6. Leveling Platform
Note: The platform has been leveled at the factory. If it needs leveling due to transportation or other reasons, please follow the steps below to
adjust the printing platform.
1. Raise the platform, loosen rubber screws on the left
and right sides of the resin vat, and take out the resin vat.
2. Loose the four screws on the connecting
plate on molding platform plate, attach
calibration card on the printing screen,
press Settings →Print Settings→ Z axis
movement →Leveling, Check whether the
platform fits evenly with the paper by
referring to the steps on Page 8.
3.After confirming that the calibration
card fit evenly, lock the four screws of the
platform.

08
6. Leveling Platform
Note: The UI is only for reference only and shall be subject to the actual UI.

09
7. Load Resin
Tips: How to change resin?
Take out the resin vat slowly, pour out the remaining resin into the container,
clean the resin vat, pour in new resin,and then install the resin vat to the
machine.
Caution: Resin may cause skin irritation or an allergic skin reaction.
Please wear gloves before use to avoid direct contact with the skin.
650ml
450ml
250ml
Pour the UV photosensitive resin into the resin vat. The slot capacity is 250ml/450ml/650ml.

10
8. Release Film (FEP) Replacement
a. First, remove the 14 screws at the bottom of thetray and take
out the broken release film (FEP).
b. Then place the release film between the two steel frames.
c. Finally,put the assembled steel frame back into the tray and
tighten 14 screws.
d. The installed release film is as show.

11
9. USB Disk Printing
Note: The published UI of slicing software shall prevail for the interfaces of HALOT BOX, LycheeSlicer and CHITUBOX.
1. Slicer
2. If the model needs to add support, click the upper left icon①
to set corresponding parameters②.
wait for slice to be finished→Select "Local Printing" to save
the sliced file.
4
kcilC 3. Click icon ①→Setting slice printing parameters②→
①
①
②
1. Open the slicer software of HALOT BOX, click "Open" on the
top left of the screen and add model file;
②
①
②

12
9. USB Disk Printing
2. Insert the USB disk
USB port
Warning: During the printing process the machine can’t be shaken,
so as not to avoid influencingaffect the printing quality.
2. Print
1. Generate cxdlp file and save the file to U disk
ctb(.ctb)
3D objects
file name
Hide Folder
Save type
preservation cancel
tower
Note: The UIinterface is for reference only,and shall be subject to the
actual UI.

13
9. USB Disk Printing
Note: The UI interface is for reference only, and shall be subject to the actual UI. The machine stores the file being printed by default.
2. Choose to use parameters；
1. Select USB disk files;
3. Press "Start" button 4. Printing···
0.05mm
0.05mm 0.05mm
0
11 1
0

14
10. Creality Cloud Online
Note: The UIinterface is for reference only,and shall be subject to the actual UI.
Make sure WiFi is correctly connected before using online printing
Steps: Settings → WiFi → Select the corresponding WiFi.
1. Click Creality Cloud online model； 2. Select the model;
3. Download the model; 4. Choos to use parameters； 5. Click "Start" to print.
0.05mm 0.05mm
0
1
0
1
Warm Tips: ① Only 2.4GHz WiFi is applicable to the 3D printer, and it cannot be connect to 5GHz WiFi routers;
② Only WPA-PSK/WPA2-PSK security protocol is applicable to the 3D printer, and other protocols may result in the failure to
connect the printer to WiFi properly. To change the security protocol, users may change it in setting interface of the router.

11. Creality Cloud App Print
15
2.Register 4. Scan QR Code
Settings → Detail →
Connect to Creality Cloud → QR code
8. Select device
5. Device naming
1.Download 3. Add equipment
9. Print progress6. Select model, set the printer and
parameters, and click "Slice".
7. Upon completion of
slicing, click "Printer".
巴黎铁塔
Notes:
1. The steps for adding devices vary for
different mobile phone operating
systems;
2. Set the correct area in "Settings - Other
Settings - Language and Area".
3.Make sure WiFi is correctly connected
before using online printing.

16
12. WIFI Print
1. Slicer
2. If the model needs to add support, click the upper
left icon to set corresponding parameters.
3. Click icon ①→Setting slice printing parameters②
→Click. 4. wait for slice to be finished→Select "Remote Printing"
for WiFi printing.
①
②
5. Once the transmission is over, select the file on the
machine to start printing.
①
②
1. Open the slicer software of HALOT BOX, click“open”
on the left of the screen and add model file.
Note: Make sure the HALOT BOX and the printer are
connected to the same WiFi.