Crestron CP2 User manual

This document was prepared and written by the Technical Documentation department at:
Crestron Electronics, Inc.
15 Volvo Drive
Rockleigh, NJ 07647
1-888-CRESTRON

Crestron CP2/CP2E 2-Series Integrated Control Processor
Contents
2-Series Integrated Control Processor: CP2/CP2E 1
Introduction ...............................................................................................................................1
Features and Functions................................................................................................1
Specifications ..............................................................................................................2
Physical Description....................................................................................................3
Memory .......................................................................................................................7
Industry Compliance ...................................................................................................9
Setup/Installation .......................................................................................................................9
Rack Mounting ............................................................................................................ 9
Bussing Strip Installation ..........................................................................................10
Network Wiring.........................................................................................................11
Hardware Hookup ..................................................................................................... 12
Optional Power Supply..............................................................................................13
Programming the CP2 and CP2E.............................................................................................13
CP2/CP2E Device Library Symbols..........................................................................13
Converting Programs and Modules Created for other Systems................................. 18
Establishing Communication with the CP2/CP2E.....................................................20
Troubleshooting Communications ............................................................................22
Compiling and Uploading a Program to the Control System ....................................24
Uploading Web pages to the CP2E ...........................................................................25
Uploading Touchpanel Projects via the CP2/CP2E...................................................26
Updating the Operating System................................................................................. 26
Advanced Console Commands..................................................................................27
Troubleshooting....................................................................................................................... 28
Passthrough Mode .....................................................................................................29
Further Inquiries ......................................................................................................................31
Future Updates......................................................................................................................... 31
Software License Agreement................................................................................................... 32
Return and Warranty Policies .................................................................................................. 34
Merchandise Returns / Repair Service ...................................................................... 34
CRESTRON Limited Warranty.................................................................................34
Operations Guide - DOC. 5980 Contents •i

Crestron CP2/CP2E 2-Series Integrated Control Processor
2-Series Integrated Control
Processor: CP2/CP2E
Introduction
Features and Functions
Crestron’s CP2 and CP2E 2-Series Integrated Control Processors, cost-competitive
options in Crestron's 2-Series line of integrated control systems, are designed for
smaller home and commercial network systems. Like all Crestron control processors,
the CP2 and CP2E units house the control system software program and provide
connectivity for communication and control of all devices on the network. The CP2E
is functionally identical to the CP2, with the exception that it also provides LAN and
Web access through its built-in 10/100 BaseT Ethernet port, which supports
dynamic/static IP addressing and full-duplex TCP/IP and UDP/IP protocols.
With speed, power, and massive memory, the 2-Series control systems are ideal for
enhanced applications like media help desks, videoconferencing, distance learning,
and entertainment facilities.
Functional Summary
•
Powered by 2-Series Control Engine
• 36 MB of Internal Memory
• 8 IR/Serial Ports
• 8 Isolated Relay Ports
• 8 I/O Versiports
• 3 RS-232/422/485 Ports
• 1 RS-232 Computer Port
• 1 Cresnet Port
• Supports SIMPL™Windows®& SIMPL+™
• Built-In 10/100 BaseT Ethernet Port (CP2E only)
• Built-In Web Server (CP2E only)
As with all of Crestron’s 2-Series control processors, the 2-Series Control Engine is
a solutions-driven control technology that is at the very heart of the CP2 and CP2E
products. The breakthrough 2-Series Control Engine is based on the 257 MIPS, 32-
Operations Guide - DOC. 5980 2-Series Integrated Control Processor: CP2/CP2E•1

2-Series Integrated Control Processor Crestron CP2/CP2E
bit Motorola ColdFireprocessor. The 2-Series operating system is vastly upgraded
from Crestron’s X-generation products, yet compatible with existing Crestron
software and programming. A key feature is the new Crestron Compiler, which
allows any existing Crestron SIMPL™ Windowscontrol program to be easily
recompiled for the 2-Series. The real-time, preemptive multi-tasking/multi-threaded
operating system offers a file system that supports long file names. The enhanced
SIMPL+™ instruction set is also fully compatible with existing Crestron SIMPL
Windows and SIMPL+ programs.
Specifications
Specifications for the CP2 and CP2E are given in the following table.
CP2/CP2E 2-Series Integrated Control System Specifications
SPECIFICATION DETAILS
CPU 32-Bit Motorola ColdFire®Processor
Processor Speed 257 MIPS (Dhrystone 2.1 Benchmark)
Memory 36MB (4MB flash, 32MB DRAM, 256KB NVRAM)*
Ports/Connectors**
NET
COMPUTER
INFRARED – SERIAL OUTPUT
I/O
RELAY OUTPUT
LAN (CP2E only)
COM (A, B, & C)
24VDC
Reset Buttons
HWR
SWR
1 – Cresnet 4-wire interface (Expandable via Cresnet
Poll Accelerator)
1 – DB9F PC interface
8 – Simultaneous one-way IR or serial output
8 – Programmable digital/analog inputs & digital outputs
8 – Normally open, isolated relays (MOV suppression)
1 – RJ45 10/100 BaseT Ethernet port
3 – DB9 bidirectional serial ports (RS-232, -422, -485),
all Cresnet Poll Accelerator ready
1 – Male receptacle for optional external power pack.
Initiates system hardware reset
System restart with or without program
Power Requirements 24 VDC, 1A, 24W (Power supply not included)***
Network Power Fuse Rating Internal self-resetting fuse****
Environmental Temperature &
Humidity
41° to 113°F (5° to 45°C)
10% to 90% RH (non-condensing)
Dimensions & Weight Height: 1.7 in (4.32 cm)
Width: 19.0 in (48.26 cm) – with ears
17.03 in (43.24 cm) – without ears
Depth: 6.64 in (16.87 cm)
Weight: 3.54 lb (1.59 kg)
* For more information on system memory usage, see Memory on page 7.
** For more information on controls, ports, and indicators, see Physical Description on page 3.
*** For information on optional power source, see Optional Power Supply on page 13.
**** Heat-sensitive device—resets within approximately 30 seconds after overload condition is
removed.
2 •2-Series Integrated Control Processor: CP2/CP2E Operations Guide - DOC. 5980

Crestron CP2/CP2E 2-Series Integrated Control Processor
Physical Description
The CP2/CP2E integrated control systems are housed in black enclosures with
labeling on the front and rear panels. The front panels of both units include standard
LEDs and two reset buttons. All connections to the units are made through their rear
panels. The front panels of the CP2 and CP2E are shown below.
Front and Rear Panels
The front panels of the CP2 and CP2E are shown below.
CP2/CP2E Front Panels
The rear panels of the units are shown below. Both units contain a single RS-232
computer port, a network connector, three COM ports, eight one-way IR/serial ports,
eight I/O ports, eight relay ports, and a 24VDC male receptacle for power supplied
through an AC power pack (purchased separately). The CP2E also contains a single
Ethernet port.
CP2/CP2E Rear Panels
Rubber feet are supplied and can be attached to the base of the unit for stability and
to prevent slippage in shelf placement and stacking configurations. The unit may also
be rack mounted by attaching the supplied metal flanges (ears).
Operations Guide - DOC. 5980 2-Series Integrated Control Processor: CP2/CP2E•3

2-Series Integrated Control Processor Crestron CP2/CP2E
Controls and Indicators
The CP2/CP2E front panel indicators and controls are described below.
PWR (Power)
This LED illuminates when the unit is connected to and receives 24VDC power from
an AC power pack or the Cresnet NET connector.
NET
This LED illuminates when the central processing unit is processing or
communicating with Cresnet devices (i.e., button pressed at Cresnet panel or data
received from Cresnet panel).
ERR
This LED illuminates when an error condition is detected. This may be the result of
hardware or software failure, or a programming error. To determine the actual error
condition, examine the message available through the Viewport menu Functions/2-
Series/errorlog.
LNK (LAN) – (CP2E only)
This LED illuminates when there is a connection to the rear panel LAN port.
ACT (LAN) – (CP2E only)
This LED illuminates when there is communication (activity) at the rear panel LAN
port.
HWR
Pressing this button initiates system hardware reset. (Same effect as disconnecting
and reconnecting power.)
SWR
Pressing this button in combination with the HWR button performs a system restart
without loading the program (refer to Troubleshooting Communications on page 22).
Pressing it alone while the system is running restarts the program.
Ports
The CP2/CP2E rear panel ports are illustrated and described below.
COMPUTER
COMPUTER
This DB9F connector is used when programming the units with a PC. The port is
modem compatible. The modem and/or PC program cable are not included.
NET
G Z Y 24
24VDC 24W
NET
4 •2-Series Integrated Control Processor: CP2/CP2E Operations Guide - DOC. 5980

Crestron CP2/CP2E 2-Series Integrated Control Processor
NOTE: The orientation of this connector is “upside down” compared to other
Crestron network devices (e.g., CNX-BIPAD8, CNX-RMCLV). Be sure the mating
Cresnet cable connector is properly aligned before attempting to insert it, to avoid
damage to the CP2/CP2E unit.
This connector (typical Crestron network port labeled G Z Y 24) is used for
expansion to Cresnet and SmarTouch peripherals. This connector can also serve as a
24W power source to the network when CP2/CP2E unit power is supplied through
the 24VDC power supply connector by an optional AC power pack (purchased
separately); otherwise, power to the unit is supplied through this connector. There is
a 24W maximum load rating for power output. Refer to “Network Wiring” on page
11 for details.
COM (A – C)
COM C
COM B
COM A
These three DB9 (male) software programmable, bi-directional serial ports are
available for RS-232, RS-422, or RS-485 communication, with hardware and
software handshaking. Speeds are rated up to 115,200 bps. All three ports are
Cresnet Accelerator ready. The Cresnet Poll Accelerator effectively increases the
network speed, fan-out, and device addresses by a factor of 8 for each Poll
Accelerator added to the system.
NOTE: The pinout of each 9-pin port is non-standard (refer to the table after these
notes, titled "Non-Standard COM Pinout"); it contains RS-422 pins in addition to
RS-232. This may result in a conflict with some equipment and therefore all nine
pins should not be used. Only the required pins for each communication type should
be connected. For RS-232 and –422, pins 2, 3, 5, 7, and 8 are wired straight through.
NOTE: Data Set Ready (DSR) and Data Terminal Ready (DTR) are not supported.
NOTE: To support RS-485, tie pin 1 (RXD-) to pin 9 (TXD-) and pin 4 (TXD+) to
pin 6 (RXD+) in the cable (refer to the table after this note, titled "COM Pinout to
RS-485 Bus".
Non-Standard COM Pinout
PIN DIRECTION DESCRIPTION
1* To CP2/CP2E (RXD-) RS-422 Receive Data (Idles low)
2 To CP2/CP2E (RXD) RS-232 Received Data
3 From CP2/CP2E (TXD) RS-232 Transmitted Data
4 From CP2/CP2E (TXD+) RS-422 Transmit Data (Idles high)
5 RS-232 and RS-422 Signal Common
6 To CP2/CP2E (RXD+) RS-422 Receive Data (Idles high)
7 From CP2/CP2E (RTS) RS-232 Request to Send
8 To CP2/CP2E (CTS) RS-232 Clear to Send
9 From CP2/CP2E (TXD-) RS-422 Transmit Data (Idles low)
Where: *= RS-422 transmit and receive are balanced signals requiring two lines plus a ground in each
direction. RXD+ and TXD+ should idle high (going low at start of data transmission). RXD-
and TXD- should idle low (going high at start of data transmission). If necessary, RXD+/RXD-
and TXD+/TXD- may be swapped to maintain correct signal levels.
Operations Guide - DOC. 5980 2-Series Integrated Control Processor: CP2/CP2E•5

2-Series Integrated Control Processor Crestron CP2/CP2E
COM Pinout to RS-485 Bus
COM (DB9) CONNECTOR RS-485 BUS
Tie Pins 1 & 9 -
Tie Pins 4 & 6 +
Pin 5 G
INFRARED – SERIAL OUTPUT
A B C D
E F G H
S G S G S G S G
INFRARED - SERIAL OUTPUT
S G S G S G S G
These connectors provide eight serial outputs for IR or serial interface. Each output
is labeled S (signal) and G (ground). Infrared output is rated up to 1.2 MHz, at data
rates up to 115K. Serial protocols include one-way RS-232.
NOTE: Transmission levels on the infrared – serial output connectors are in the 0 to
+5VDC range, which may not be compatible with all RS-232 devices.
I/O
1 2 3 4 5 6 7 8 G
I/O
This connector provides eight software programmable analog and digital inputs as
well as digital outputs. Digital outputs offer 250mA sync from maximum 24 VDC;
catch diodes for use with "real world" loads. Digital inputs are rated 0 – 24 VDC,
20K ohms input impedance, logic threshold 1.25 VDC. Analog inputs are rated 0 –
10 VDC, protected to 24 VDC maximum, 20K ohms input impedance; pin-
programmable 2K ohms pullup resistor to +5V.
NOTE: Digital outputs are TTL values and may not work with devices requiring a
“dry” contact closure (e.g., low voltage motor controllers).
RELAY OUTPUT
OUTPUT
1 2 3 4 5 6 7 8
RELAY
These connectors provide eight normally open, isolated relay contact groups. Each
relay contact closure is rated 1A, 30 VAC/DC; MOV arc suppression is provided
across contacts for use with "real world" loads.
6 •2-Series Integrated Control Processor: CP2/CP2E Operations Guide - DOC. 5980