Crestron DigitalMedia 8G+ DM-RMC-4K-100-C-1G Dimensional drawing

DO GUIDE
DO Install the Device
The DM-RMC-4K-100-C-1G can be mounted into an electrical box, under a table, or onto a at
surface or rack rail.
Mounting into an Electrical Box
The DM-RMC-4K-100-C-1G mounts into a 1-gang electrical box (not included). A minimum mounting
depth of 3-1/2 inches (89 mm) is required.
Using a Phillips screwdriver (not included), attach the DM-RMC-4K-100-C-1G to the electrical box
using the two included 6-32 x 3/4-inch truss combo head screws. Then, attach a decorator-style
faceplate (not included) to the front panel of the DM-RMC-4K-100-C-1G using two screws
(not included).
Mounting into an Electrical Box
DM-RMC- 4K-10 0-C-1G
Wall Plate 4K DigitalMedia 8G+®Receiver
and Room Controller 100
DO Make Connections to the Rear Panel
Make connections to the rear panel of the DM-RMC-4K-100-C-1G before mounting the unit into
an electrical box. If the unit is to be mounted under a table or onto a at surface or rack rail, make
connections to the rear panel after the unit is mounted. (For mounting instructions, refer to the
“DO Install the Device” section.)
Make connections to the rear panel as follows:
DM IN: Connect to the DM 8G+®output of a DigitalMedia™ switcher, DigitalMedia 8G+®transmitter,
or other DigitalMedia device or to an HDBaseT® device.
DM IN Wiring
NOTE: The DM IN port is a PoDM powered device (PD) port and is also compatible with HDBaseT
PoE. In order for the DM-RMC-4K-100-C-1G to receive PoDM, the device requires connection to a
DigitalMedia switcher or other equipment that has a PoDM power sourcing equipment (PSE) port. In
order for the device to receive HDBaseT PoE, the device requires connection to equipment that has
a corresponding HDBaseT PoE PSE port. Any wiring that is connected to a PoDM or HDBaseT PoE
PSE port is for intrabuilding use only and should not be connected to a line that runs outside of the
building in which the PSE is located.
24VDC 0.75A: Connect to the included power pack using the included 2-pin interface connector.
Power Pack Wiring
NOTE: Connection to the power pack is not required when PoDM or HDBaseT PoE is used to power
the device.
G: Connect to earth ground (building steel).
DO Check the Box
QTY PRODUCT COLOR PART NUM.
1Bracket (for Interface Module) Black 2016054
2Connector, 2-Pin 2003574
1Connector, 3-Pin 2003575
1 Power Pack, 24 Vdc 0.75 A, 100-240 Vac 2045866
2 Screw, 6-32 x 1/4", Pan Head, SEMS Black 2007218
2 Screw, 6-32 x 3/4", Truss Head, Combo 2009211
Pin 1
Pin 8
PIN
NUM. WIRE COLOR PIN NUM. WIRE COLOR
1Orange/White 5Blue/White
2Orange 6Green
3Green/White 7Brown/White
4Blue 8Brown
DM-MD8X8
Ground
Connection to DigitalMedia Transmitter
(External Power Pack Required)
Power
pack
USBHID HDMI RGB AUDIO SETUP
DM-T X - 2 0 1 - C
DM CO M P U T E R C E N T E R
RESET
IN
LAN DMOUT HDMIOUT
PWR
24VDC
0.75A
DM-TX-201-C
Ground
Connection to DigitalMedia Switcher Using
PoDM (External Power Pack Not Required)
SIGNAL LEAD COLOR
GBlack
24 Black with White Stripe

DO GUIDE DOC. 7707E (2042251) 06.17
Specications subject to change without notice.
Mounting under a Table or onto a Flat Surface
The DM-RMC-4K-100-C-1G mounts under a table or onto a
suitable at surface using the included surface mount bracket.
Using a Phillips screwdriver (not included), attach the included
surface mount bracket to the DM-RMC-4K-100-C-1G using the two
included 6-32 x 1/4-inch SEMS screws. Then, attach the bracket to
the underside of a table or onto a at surface using two mounting
screws (not included).
Mounting under a Table or onto a Flat Surface
Mounting onto a Rack Rail
The DM-RMC-4K-100-C-1G mounts onto the front or rear rail of a
rack. Position the DM-RMC-4K-100-C-1G horizontally so that the
holes in the left or the right mounting ange align with the holes
in the rack rail. Then, secure the unit to the rack rail using two
mounting screws (not included).
Mounting onto a Rack Rail
DO Make Connections to the Front Panel
Make connections to the front panel of the
DM-RMC-4K-100-C-1G as required for the application.
HDMI OUT: Connect to the HDMI®input of the receiving device.
IR OUT: Connect to the Crestron®IRP2 emitter probe (not
included) using the included 2-pin connector.*
COM: Connect to the device to be controlled using the included
3-pin connector.*
Sample Front Panel Connections
*The IR OUT port and the COM (RS-232) port are enabled only when the
DM-RMC-4K-100-C-1G connects to an Ethernet-enabled DigitalMedia transmitter
or switcher that is addressable from a Crestron control system.
DO Learn More
Visit the website for additional information and
the latest rmware updates. To learn more about
this product, use a QR reader application on your
mobile device to scan the QR image.
Crestron Electronics
15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com
As of the date of manufacture, the product has been tested and found to comply with specications for CE marking.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
CAUTION:Changes or modications not expressly approved by the manufacturer responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada (IC) Compliance Statement
CAN ICES-3(B)/NMB-3(B)
The specic patents that cover Crestron products are listed at www.crestron.com/legal/patents. The product warranty can be found at www.crestron.com/warranty.
Certain Crestron products contain open source software. For specic information, please visit www.crestron.com/opensource.
Crestron, the Crestron logo, DigitalMedia, DigitalMedia 8G+, and DM 8G+ are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries.
HDBaseT and the HDBaseT Alliance logo are either trademarks or registered trademarks of the HDBaseT Alliance in the United States and/or other countries. HDMI and the HDMI logo are
either trademarks or registered trademarks of HDMI Licensing LLC in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this
document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible
for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2017 Crestron Electronics, Inc.
IRP2 emitter probe
Projector