CrimeStopper CS-9701 Gargoyle User manual

CRIMESTOPPER SECURITY PRODUCTS CS-9701
Wiring
Main Harness: 10 pin 18 gauge wires
Red Wire: +12Volt Power
Connect to constant +12volt power source with supplied in line 10 amp fuse and fuse holder.
Black Wire: Chassis Ground
Connect to body metal of the vehicle using a sheet metal screw.
Yellow Wire: Ignition Switched "ON" and "START" +12Volts
Connect to an Ignition Wire (or fuse in the fuse box) that shows +12Volts when the key is in both the
"ON" and "START" positions.
Orange Wire: (-) Negative Starter Disable Output (optional)
This wire is connected to terminal 85 of a relay for the starter disable. Connect terminal 86 to the Yellow
ignition switched wire. Cut the vehicle starter wire. Connect one half to terminal 30 and the other half to
terminal 87a.
White Wire: +12Volts Flashing Parking Light Output (optional)
Connect to any parking light or to the parking light output at the back of the headlight switch. ! ! ! DO
NOT CONNECT TO DASH DIMMER CIRCUIT ! ! !
Brown Wire: + Siren Output
Connect brown wire to siren red wire. Connect black wire of siren to chassis ground (body metal).
Blue Wire: (-) Hood/Trunk Pin Switch Input
Connect to pin switches which go to ground when hood and trunk are opened. It may be necessary to
install your own switches.
Green Wire: (-) Door Pin Switch Input
Connect to door switches which go to ground when door is opened. A (-) negative door switch wire will
read +12 volts when doors are closed.
Violet Wire: (+) Door Pin Switch Input
Connect to door switches which go to +12 volts when door is opened. A (+) positive door switch wire will
read (-) ground when doors are closed.
Gray Wire: (-) Negative Remote Output (optional, requires relay)
Connect to terminal 85 of relay. Connect terminal 86 to +12Volts constant. Connect terminal 87 to
+12volt constant or (-) ground. Connect terminal 30 to device to be activated.
Sensor Plug: 4 Pin 22 Gauge
White Wire -Negative Warn Away
Blue Wire -Negative Trigger
Black Wire -Sensor Ground
Red Wire -Sensor +12Volt Power
The sensor supplied with this system requires no additional wiring. Simply mount the sensor in a suitable
location and plug it in. Adjust sensitivity as necessary.
LED and Override/Valet Switch Plug: 2 Pin 22 Gauge
Connect LED plug to Red Connector on module and connect Override/Valet plug to Blue connector on
module.

Power Door Locks: 3 Pin 22 Gauge (optional)
Blue Wire (-) Negative Door Unlock Output
Connect to factory unlock relay or to relay to activate motors.
Green Wire: (-) Negative Door Lock Output
Connect ot factory lock relay or to relay to activate motors.
Red Wire (+) +12Volts Constant
Connect to terminal 86 of after market relay for activating positive, reverse polarity and after market door
locking systems. DO NOT USE THIS RED WIRE FOR MAIN POWER TO ACTIVATE DOOR LOCK
MOTORS.
Programming Dip Switches
There are 4 dip switches under the access door of the control module for pre installation programming.
Dip Switch #1: Door Lock/Unlock Pulse Time
ON: Pulse time = .75 seconds
OFF: Pulse Time = 3 seconds
Dip Switch #2: Ignition Controlled Lock/Unlock
ON: Lock/Unlock with ignition
OFF: "NO" Lock/Unlock with ignition
Dip Switch #3: Passive Arming Locks
ON: Doors lock when system arms passively
OFF: Doors do not lock when system arms passively
Dip Switch #4: Passive / Active Arming Select
ON: Alarm arms automatically 30 seconds after last door is closed (PASSIVE)
OFF: Alarms arms only with remote control (ACTIVE)
Transmitter Programming
This system uses code learning to learn up to 3 different transmitter codes. Follow these 4 simple steps
to program a transmitter to your system.
1. Turn ignition switch on -off -on -off -on. Siren will chirp once.
2. Push the Valet/Override switch for 5 seconds until the siren chirps 3 times. Release the Valet Switch.
3. Press the Large Button or button #1 of the transmitter -The Siren will chirp to confirm programming.
Repeat this procedure within 5 seconds for up to 2 additional transmitters.
4. Turn off ignition.
Note 1: If only one transmitter is being programmed, continue holding button #1 until dash LED flashes 4
times. This means the system has exited program mode. Holding the transmitter button until the LED
flashes prevents unauthorized code and noise from entering the system.
Note 2: Program mode is exited automatically after 5 seconds of last code transmission or once three
new codes have been programmed. LED will flash 4 times indicating program mode has terminated.

OWNERS INSTRUCTIONS:
Active Arming Mode:
Press button #1 once momentarily. Alarm arms and confirms with:
1 Siren Chirp
Lights flash once
LED lights solid then starts flashing slowly
Power locks will lock (if equipped)
Starter circuit enabled (optional)
Disarming:
Press button #1 once momentarily. Alarm disarms and confirms with:
2 Siren Chirps
Lights flash twice
LED stops flashing (turns off)
Power locks will Unlock (if equipped)
Starter circuit disabled (optional)
Silent Active Arming/Disarming Mode:
To Activate, turn ignition on, within 10 seconds press button #2 for 3 seconds.
Siren will emit a double chirp -Silent Arm/Disarm mode is on. System will operate without siren chirps.
Alarm will remain chirp less until Silent Mode is deactivated.
To De-Activate, turn ignition on, within 10 seconds press button #2 for 3 seconds.
Siren will emit 2 double chirps -Silent Arm/Disarm mode is off. System will operate with siren chirps.
Passive Arming Mode: Optional
Must be programmed -Consult your installer.
When exiting the vehicle, upon closing the last door there will be a 30 second delay before arming. The
LED will be flashing rapidly indicating the system is in passive arming mode. After the delay, the system
will arm and confirm with:
1 Siren Chirp
Lights flash once
LED starts flashing slowly
Power locks will lock (if equipped & dip switch # is ON)
Starter circuit enabled (optional)