Crown Cm-311ae Service manual

GLM-100E, CM-311E

CM-311AE, CM-312E, CM-312AE

CONNECTIONS FOR WIRELESS

MICROPHONE APPLICATIONS

For more help, contact one of these technical

support numbers:

Crown 800-342-6939

AKG 800-878-7571

Audio-Technica 330-686-2600

Beyerdynamic 800-293-4463

Comtek 800-496-3463

Electro-Voice 877-863-4168

HM Electronics 800-848-4468

Lectrosonics 800-821-1121

Lightspeed 800-732-8999

Nady 510-652-2411

Paso 800-231-3034

Peavey 877-732-8391

Samson 800-3-SAMSON

Shure 847-600-8440

Sony 866-766-9272

Telex 800-553-5992

TOA 800-733-4750

Vega 800-877-1771

AS OF AUGUST 1, 2008

Crown Audio, Inc.

1718 W. Mishawaka Rd.

Elkhart, IN 46517-9439

TEL: 574-294-8000

FAX: 574-294-8FAX

www.crownaudio.com

Latest information available at www.crownaudio.com.

Crown® and Crown Audio are registered trademarks of

Crown International. Other trademarks are the property

of their respective owners.

8/08 125491-10

Disclaimer: This information is provided “as is” and does not make any express or implied warranties, representations or endorsements whatsoever (including without limitation

warranties of title or noninfringment, or the implied warranties of merchantability or ﬁtness for a particular purpose) with regard to any merchandise information presented here.

It is solely your responsiblility to evaluate the accuracy, completeness and usefulness of the information provided here.

Limitation of Liability: In no event will Crown Audio, Inc. be liable for (1) any incidental, consequential, or indirect damages (including but not limited to damages for loss of

proﬁts, business interruption, and the like) arising out of the use of the information provided here, or (2) any claim attributable to errors, omissions, or other inaccuracies in the

information provided here. Because some states do not allow the exclusion or limitation of liability for consequential or incidental damages, the above limitation may not apply to

you. In such states, Crown Audio, Inc.’s liability is limited to the greatest extent permitted by law.

CONNECTIONS TO GLM-100E

You can connect the GLM-100E for unipolar or bipolar powering. With unipolar powering (B+ and ground), the GLM can handle up to 120 dB SPL

without distortion. With bipolar powering (B+ and B- relative to ground), the GLM can handle up to 150 dB SPL. Not all transmitters provide bipolar

powering.

AKG TA3F 1-shield

WMS40 (PT40) 2-white

WMS400 (PT400) 3-red

WMS4000

(PT4000)

________________________________________________________

Audio-Technica Hirose HRI0- 1 and 2-shield

ATW, T31, T35, 7P-4S 3-white

T27, WT-15, 4-red

T51, T75,

ATW T21 4 pin DIN case-shield

1-white

3-red

Beyerdynamic Lemo FG331 1-shield

TS-170, TSP, 2-red

TS-600 3-white

TS-190, 4-pin binder 2-shield

TS-900 (UHF) conn. #711 3-white

4-red

Comtek 750 mono mini, 1-shield

M72, M72-B 851 micro mini, 2-white

Switchcraft TA4F, 3-red

Lemo 4-pin

Electro-Voice Switchcraft TA4F 1-red

MB2000A, 3-white

MB2500 4-shield

HME Switchcraft TA4F 1-shield

TX-425, TX-550, 2-white

TX-822 3-red

Lectrosonics Switchcraft TA5F 1and 4-shield

M185, UM190, 2-red

UM195, M187, 3-white

UM200

Lightspeed Hirose HR10- 1-shield

Technologies 7P-4S 3-white

BP Series 4-red

Nady Switchcraft TA3F 1-shield

All models 2-red

3-white

Paso MA-23, Switchcraft TA3F

MA-27 1-shield

2-white and red

3-jumper to pin 1

Peavey Switchcraft TA3F 1-red

BPX 2-shield and white

Samson Hirose HR10- 1-red

TX-3, UT-5, 7P-6S 2-white

UT-4, BT-3, CT-2 6-shield

MODEL CONNECTOR PINS

GLM-100E WIRING, 3-WIRE POWER GLM-100E WIRING, 2-WIRE POWER

MODEL CONNECTOR PINS

Samson ST-2 Hard wired 1 and 2-shield

3-red (B+)

4-white (audio)

Samson CT-3 Hard wired 1-red (B+)

2-white (audio)

3 and 4-shield

Sennheiser Sennheiser/ Ground-shield and white

SK-2012 B&K microdot Center-red

Lemosa 2-red

3-white and shield

shell-shield

Shure Switchcraft 1-shield

L-11, SC1, LX1, TA4F 2-red

U-1 (UHF), T-1 3 and 4-white

UT-1, UC-1

U1L-VA Lemo 4-pin 1-white

UC1L 2-red

4-shield

3-jumper to pin 1

Sony SMC-9 1-red

WRT-28, 2-white

WRT-820A 3 and 4-shield

Telex Switchcraft TA4F 1-shield

WT-55, WT-60, or Lemo 4-pin 2-white

WT-80, WT-150, 3-red

WT-450

TOA Mini phone plug Tip-red,

WM-340U, Sleeve-shield and white

WM-370 To prevent capsule

damage from static sparks,

solder a 3.3K resistor

between white and tip.

Vega Lemo 4-pin 1-white

F.O. 304 2-red

NYL U/3.2 4-shield

If RFI is a problem, solder a 560 pF cap. between pins 1 and 4.

Switchcraft TA4F 1-red

3-white

4-shield

X-wire TA3F 1-shield

2-white

3-red

AKG TA3F 1-shield

WMS40 (PT40) 2-white

WMS400 (PT400) 3-red

WMS4000 (PT4000)

Audio-Technica Hirose HR10- 1 and 2-shield

ATW 7P-4S 3-white

T35, T27, 4-red

WT-15

ATW T21 4 pin DIN case-shield

(now obsolete) 1-white

3-red

Beyerdynamic Lemo FG331 1-shield

TS-170, TSP 2-red

TS-600 3-white

TS-190, 4-pin binder 2-shield

TS-900 (UHF) conn. #711 3-white

4-red

Comtek 750 mono mini, 1-shield

M-72, M72-B 851 micro mini, 2-white

M-182, M-82 Switchcraft TA4F 3-red

or TA3F, Lemo

4-pin

Electro-Voice TA4F 1-red

MB2000A 3-white

MB2500 4-shield. If RFI, use

200-560 pF capacitor

between

pins 3 and 4

R100 see Telex notes

R200 see Telex notes

HME Switchcraft TA4F 1-shield

All models 2-white

3-red

HME note: To increase bass and reduce treble at the expense of output

level, solder a 6.8K resistor between pin 2 and its wire

inside the transmitter.

Lectrosonics Switchcraft TA5F 1-shield

M185, M187 2-red

UM190, UM195 3-white

UM200

Lightspeed Hirose HR10- 1-shield

Technologies 7P-4S 3-white

BP Series 4-red

Nady Switchcraft TA3F 1-shield

All models 2-red

3-white

CONNECTIONS TO CM-311AE, CM-312AE AND CM-312E

MODEL CONNECTOR PINS

Samson Hirose HR10- 1-red

TX-3, UT-4, 7P-6S 4-white

BT-3, CT-2 6-shield

UT-5 Hirose HR10- 1-red

7P-6S 2-white

6-shield

ST-2 No connector 1 + 2-shield

3-red (B+)

4-white (audio)

CT-3 No connector 1-red (B+)

2-white (audio)

3 + 4-shield

Shure Switchcraft TA4F 1-shield

L-11, SC1, LX1, 2-red

U-1 (UHF), T-1 3-white

4-jumper to pin 3

U1L-VA Lemo 4-pin 1-white

UC1L 2-red

4-shield

3-jumper to pin 1

Sony

WRT-820A SMC-9 1-red +5V

2-white

4-shield

WRT-805A 3.5 mm T-white

mini-plug R-red +5V

S-ground

Telex Switchcraft TA4F 1-shield

WT-55, WT-60, or Lemo 4-pin 2-white

WT-80, WT-150,

3-red

WT-450

Vega Lemo 4-pin 1-white

F.O. 304

2-red

NYL U/3.2

4-shield

Switchcraft TA4F 1-red

3-white

4-shield

X-wire TA3F 1-shield

2-white

3-red

MODEL CONNECTOR PINS

CONNECTIONS TO CM-311E

MODEL CONNECTOR PINS

Nady Switchcraft TA3F 1-shield

All models

2-red. Remove connection,

connect pin 2 to battery +.

3-white

Samson Hirose HR10- 1-red

TX-3, UT-4 7P-6S Remove connection,

BT-3, CT-2 connect pin 1 to battery +.

4-white

6-shield

UT-5 Hirose HR10- 1-red

7P-6S 2-white

6-shield

ST-2 No connector 1 + 2-shield

3-red (B+)

4-white (audio)

CT-3 No connector 1-red (B+)

2-white (audio)

3 + 4-shield

Shure Switchcraft TA4F 1-shield

L-11, SC1, LX1, 2-red. For Cm-311E

U-1 (UHF), T-1 only, contact Shure for 9V

bias, mod.

3-white

4-jumper to pin 3

Sony SMC-9 CM-312E only:

WRT-28, 1-red

WRT-820A 2-white

3 and 4-shield

or try 1-red, 3-white,

4-shield

Telex Switchcraft TA4F 1-shield

WT-55, WT-60, or Lemo 4-pin 2-white

WT-80, WT-150,

4-red

WT-450

Vega Lemo 4-pin 1-white

F.O. 304

2-red

NYL U/3.2

4-shield

Switchcraft TA4F 1-red. Remove connection,

connect pin 1 to battery +.

3-white

4-shield

MODEL CONNECTOR PINS

Audio-Technica Hirose HR10- 1and 2-shield

ATW 7P-4S 3-white

T35, T27 4-red. For T31 only, remove

connection, connect pin 4

to battery +.

ATW 1031 Hirose HR10- 1-shield

7P-4S 3-white

4-red. Remove connection,

connect pin 4 to

battery +.

ATW T21 4 pin DIN case-shield

1-white

3-red

Beyerdynamic Lemo FG331 1-shield

2-red

3-white

TS-190, 4-pin binder 2-shield

TS-900 (UHF) conn. #711 3-white

4-red. Remove connection,

connect pin 4 to battery +.

Comtek 750 mono mini, 1-shield

M-72, M72-B 851 micro mini, 2-white

M-182, M-82 Switchcraft TA4F 3-red. Remove connection,

or TA3F, Lemo connect pin 3 to battery +.

4-pin

Electro-Voice TA4F 1-red

MB2000A 3-white

MB2500 4-shield. 470 pF cap. bet.

pins 3 and 4

HME Switchcraft TA4F 1-shield

All models 2-white

3-red

HME note: To increase bass and reduce treble at the expense of output

level, solder a 6.8K resistor between pin 2 and its wire inside the trans-

mitter.

Lectrosonics Switchcraft TA5F 1-shield

M185, M187 2-red. Remove connection,

UM190, UM195 connect pin 2 to battery +.

UM200 3-white

Lightspeed Hirose HR10- 1-shield

Technologies 7P-4S 3-white

BP Series 4-red

The CM-311E works only on 9V.

If your transmitter supplies 9V at its connector, you can connect a CM-311E to your transmitter as described in the chart below.

NOTE:

To convert a CM-311 or CM-311A for wireless use, either cut the cable and add the CM-311AE EQ module or connect the beltpack XLR output to the transmitter input.