Croydex WS040478 User manual

Bowmont Light Wood
Vanity Unit
This installation guide applies to the following product:
WS040478 - Bowmont Light Wood Vanity Unit
Tools Required
Cross head screwdriver, Tape Measure, Drill, 6mm Drill Bit, 6mm Ceramic Drill Bit (Optional),
Spirit Level, Silicon sealant (Not Supplied)
KEEP DIY TOOLS OUT OF THE REACH OF CHILDREN
Home Safety Advice
Do not use power screwdrivers to assemble this product.
Do not overload the vanity unit.
Maximum safe working load for the shelf is 10kg evenly distributed.
Do not strike the product with hard or sharp objects.
Product Care
Do not use abrasive or chemical cleaners as these will damage the product.
1 WSH 015 R02
It is recommended that two people fit this product to ensure that it is fitted safely.
Always take care when using power tools, particularly in the bathroom.
Always check for hidden cables and pipework before drilling and take extreme care if there is
any water in the working area.
Always wear suitable eye protection when drilling.
If the product is to be fitted on a ceramic tiled wall, a ceramic drill bit should be used.
Always ensure that the drill hole passes through the central tiled area rather than through the
grouted area. To prevent damage to the tile, mask the area around the hole with tape before
drilling.
Double check the drill bit size matches the wall plug diameter before drilling the wall.
Thank you for purchasing this Croydex product. Please follow the fixing and care instructions to
ensure that your Vanity Unit is fitted safely and that it retains its high quality finish.
Please retain this leaflet for future reference.

A x 12 B x 14 C x 16 D x 16 E x 1
F x 1 G x 4 H x 2 I x 4 J x 4
K x 1 L x 2 M x 2 N x 6
2 WSH 015 R02

Two Door White Vanity Unit
Assembly Instructions
Step 1
Part 1, Part 2, Part 3
A x 6
Insert components A into the holes
shown on parts 1, 2, 3.
Step 2
Part 4
C x 8, E x 1, N x 3
Place the relevant components
into the location shown in the
illustration.
The rails will only locate into the
3 screwholes when mounting to
the correct side panel
Step 3
Part 5, Part 6
A x 6
Insert components A into the holes
shown on parts 5, 6
3 WSH 015 R02

Step 4
Part 5, Part 6
G x 2
Secure the relevant components into
the location shown in the illustration.
Step 5
Part 1, Part 2, Part 3, Part 4
D x 4
Locate parts 1, 2, 3 as shown. To
secure Component D rotate the
screw clockwise until it locks onto
Component C. This action is
illustrated.
Step 6
Step 5 Assembly, Part 5
D x 4
Locate part 5 as shown. To
secure Component D rotate
the screw clockwise until it
locks onto Component C. This
action is illustrated.
4 WSH 015 R02
*Click
*Click

Step 7
Part 7
C x 8, F x 1, N x 3
Place the relevant components into
the location shown in the illustration.
The rails will only locate into the 3
screwholes when mounting to the
correct side panel
Step 8
Main Assembly, Part 7
D x 8
Place part 7 onto the main
assembly as illustrated and lock
into place.
To secure Component D rotate the
screw clockwise until it locks onto
Component C. This action is
illustrated.
Step 9 - Assembling the Drawer
Part 8, Part 9, Part 10, Part 11
B x 8
Secure the relevant components
into the location shown in the
illustration.
5 WSH 015 R02
160˚~185˚

6 WSH 015 R02
Step 10
Part 12, Part 13
H x 2
Secure the relevant components
into the location shown in the
illustration.
Step 11
Step 9 Assembly, Part 12, Part 13
B x 4
Secure the relevant components
into the location shown in the
illustration.
Step 12
Step 11 Assembly, Part 14
B x 2
Slide part 14 along the groove line
and secure into location.

7 WSH 015 R02
*Click
Step 13
Part 15
I x 4, K x 1, L x 2
Secure the relevant components
into the location shown in the
illustration.
Step 14
Step 12 Assembly, Step 13 Assembly
J x 4
Locate the assemblies of Step 12
and Step 13 as shown.
To secure Component J rotate the
screw clockwise until it locks onto
Component C. This action is
illustrated.
Step 15 - Mounting to wall
Main Assembly,
G x 2, M x 2
Place the unit against the wall to
mark the holes for you to drill using
an 6mm drill bit. Insert the wall
plugs into the holes and secure the
unit using component G.

For details of the other items in the Croydex range please visit our website: www.croydex.com
Croydex, Central Way, Andover, Hampshire, SP10 5AW, UK
Tel: [phone] Fax: [phone]
E-mail: [email protected]
8 WSH 015 R02
1
2
3
4
5
Step 16
Main Assembly, Drawer
Locate the drawer into the main
assembly along the slider rails.
Step 17
Main Assembly - Basin
Once your unit is fully assembled,
lower your basin on top and
secure using silicon sealant.