Croydex Norton WS010322 User manual

1
Norton Vanity Unit (80cm)
Thank you for purchasing this Croydex product. Please follow the xing and care instructions to ensure your vanity
unit is tted safely and retains its high quality nish.
Please retain this leaet for future reference.
This installation guide applies to the following vanity unit:
WS010322 - Norton Vanity Unit (80cm)
Tools required - not supplied
Pencil;Tape Measure; Philips Screwdriver; Mallet; Drill; 5mm Drill Bit; 8mm Drill Bit (Ceramic drill bit optional).
KEEP DIY TOOLS OUT OF THE REACH OF CHILDREN
Home Safety Advice
- It is recommended that two people t this product to ensure that it is tted safely.
- Always take care when using power tools, particularly in the bathroom.
- Always check for hidden cables and pipework before drilling and take extreme care if there is any
water in the working area.
- It is advisable to use a residual current circuit breaker (RCCB).
- Always wear suitable eye protection when drilling.
- If the product is to be tted on a ceramic tiled wall, a ceramic drill bit should be used.
- Always ensure that the drill hole passes through the central tiled area rather than through the grouted
area. To prevent damage to the tile, mask the area around the hole with tape before drilling.
- Do not strike the product with hard or sharp objects.
Product Care
To retain the best quality nish, clean product regularly with a soft damp cloth.
Do not use abrasive or chemical cleaners as these will damage the product.
Product Location
Vanity units are only as strong as the wall to which they are xed and the xings that are used.
For different wall types you will need to ensure that you are using the correct type of xing for the material of the wall.
The addition of backboards on the outside of the wall or appropriate strengthening of internal structures may be
required to provide adequate wall strength.
NOTE: If the wall is made of lightweight thermal blocks, aerated hollow brickwork or prefabricated partitions
even the most appropriate xings may not be able to withstand the loads which can be suddenly applied to
the vanity unit.
CAB 093 R01
Vanity Unit Components
B. Side Panel (P002) x 1
C. Front Panel (P003) x 1 F. Partition Panel (P006) x 2
A. Side Panel (P001) x 1
D. Base Panel (P004) x 1 G. Rear Panel (P007) x 3
E. Shelf Panel (P005) x 1 H. Support Panel (P008) x 1

2CAB 093 R01
C. Wall Plugs (H007) x 2 D. Wall Screws (H008) x 2A. Vanity Unit Feet Screws
(H005) x 16
B. Vanity Unit Feet
(H006) x 4
Vanity Unit Fixing Components
Installation
Step 1 A. Side Panel (P001) x 1
D. Base Panel (P004) x 1
E. Shelf Panel (P005) x 1
Click!

CAB 093 R01
3
Installation
Step 2
Click!
B. Side Panel (P002) x 1

CAB 093 R01
4
Installation
Step 3
G. Rear Panel (P007) x 3
Click!

Installation
Step 4
Installation
Step 5
CAB 093 R01
5
Stand Vanity Unit Upright!
H. Support Panel (P008) x 1
Click!

Installation
Step 6
Installation
Step 7
CAB 093 R01
6
C. Front Panel (P003) x 1
Click!
Click!
F. Partition Panel (P006) x 2

CAB 093 R01
7
Installation
Step 8
Installation
Step 9
For details of the other items in the Croydex range please visit our website: www.croydex.com
Croydex Ltd, Central Way, Andover, Hants, SP10 5AW, UK
Tel: [phone]
Fax: [phone]
Email: [email protected]
Lay Vanity Unit Down!
C. Wall Plugs (H007) x 2
D. Wall Screws (H008) x 2
A. Vanity Unit Feet Screws
(H005) x 16
B. Vanity Unit Feet
(H006) x 4
30 mm
8 mm
Ø8
Ø5