Croydex WC9300 Series User manual

CAB 140 R07
x1
A.
B.
C.
WC9300##
WC9301##
WC9302##
WC9303##
WC4516##
WC4518##
26 3/8” (670mm)
26 3/8” (670mm)
26 3/8” (670mm)
26 3/8” (670mm)
20 31/64” (520mm)
20 31/64” (520mm)
15 3/4” (400mm)
19 11/16” (500mm)
23 5/8” (600mm)
31 1/2” (800mm)
11 13/16” (300mm)
17 23/32” (300mm)
4 3/4” (120mm)
4 3/4” (120mm)
4 3/4” (120mm)
4 3/4” (120mm)
4 47/64” (120mm)
4 47/64” (120mm)
A. B. C.
EN. Please read the information sheet before proceeding.
MAX
22Ib
(10kg)
MAX
11Ib
(5kg)
Dimensions are approximate and shown for reference only.
Page 1
5/16” or 7/16”
(8mm or
11mm)

Painted Steel Cabinet
Icon Library
For reference only Parts may vary.
(Optional)
Warning! Please take
special care.
Safety and Care
Please read all of the information carefully and refer back when you see the numbered icons
throughout instructions.
CAB 140 R07
Wall Plug Mounting Screw Top Hat Bracket & Cap
Toggle Bolt Pin Handle & Screw
O-Ring O-Ring
Bottom Bracket
(Large Diameter)
Top Bracket
(Small Diameter)
Metal Washer
Mounting Screw
Spacer
Locking Cap
Cover
Metal Washer
Mounting Screw
Spacer
Locking Cap
Cover
THIS IMAGE SHOWS THE
TOP BRACKET MOUNTING
COMPONENTS
THIS IMAGE SHOWS THE
BOTTOM BRACKET MOUNTING
COMPONENTS
Page 2
TOGGLE BOLT WALL INSERT
PUSH THE 7/16” (11MM)
DIAMETER WALL INSERT
INTO THE 11MM HOLE IN
THE PLASTER BOARD FOR
MAXIMUM LOAD BEARING
STRENGTH.
1
2
5
6
7
8
3
4
9
Always take care when using power tools, particularly if there is any water in the working area.
Always check for hidden cables and pipework before drilling and take extreme care if there is any water in the
working area.
Always use a residual current circuit breaker (RCCB/GFCI).
Always wear suitable eye protection when drilling.
When drilling into a tiled surface do not use a hammer drill.
Always use a drill bit that is suitable for the surface that is being drilled.
The wall plugs supplied are for use on solid walls only. For cavity walls or plasterboard use specialist fixings
that are suitable for the type of wall construction.
Do not use power tools for assembly.
To retain the best quality finish, clean product regularly with a soft damp cloth.
Do not use abrasive or chemical cleaners, as these may damage the product.
Redecoration may be required on some painted surfaces after removal.
The max load of the cabinet is 22lb (10kg) when fitted to a solid wall and 11lb (5kg) then fitted to a cavity wall.
Do not slam the door open, this may damage the hinge.
10
11
12
13
UK: Croydex, Central Way, Andover,
Hampshire, SP10 5AW, UK
EU: MIL, Unit 8 Purcellsinch Ind Est, Dublin
Road, Kilkenny, R95 HP71, Ireland
[phone]
[phone]
[e-mail]
www.croydex.com

Place the cabinet in the desired position on the
wall and mark the position of the top mounting
hole. Note that single door cabinets can be
positioned with either a left or right opening door.
Simply turn the cabinet upside down to change
the door opening direction.
Fasten the top bracket to the wall ensuring the
O-ring is correctly seated at the back of the
bracket. Do not overtighten!
(This image shows the solid wall installation.)
Hang the cabinet onto the top wall bracket, (see
image 1) and secure in place by screwing the
locking cap and spacer onto the top bracket, (see
image 2).
Place the cover onto the locking cap, (see image 3).
Image 1 Image 2
Image 3
1. 2.
3.
4.
Page 3
IMPORTANT NOTE:THE TOP BRACKET HAS A SMALLER DIAMETER OUTER FLANGE TO THE BOTTOM BRACKET.
For solid walls drill a 5/16” (8mm) diameter hole in the marked
postion and insert a wall plug ush to the surface of the
wall. If tting to a tiled surface, the wall plug should be
inserted below the surface of the wall to avoid cracking the
tiles.
For cavity walls drill an 7/16” (11mm) diameter hole and
assemble the top bracket and metal washer onto the toggle
bolt as shown above. Ensure the 11mm diameter toggle
bolt insert is pushed into the hole in the plaster board wall
for maximum strength.
Metal Washer
7/16” (11mm)
diameter toggle
bolt wall insert
Top Bracket
(Small Diameter)
IMPORTANT!
If the wall plugs are not inserted ush with the wall
surface, the O-ring will not contact the wall correctly.
This will prevent the bracket from functioning properly.
123
CAB 140 R07
UK: Croydex, Central Way, Andover,
Hampshire, SP10 5AW, UK
EU: MIL, Unit 8 Purcellsinch Ind Est, Dublin
Road, Kilkenny, R95 HP71, Ireland
[phone]
[phone]
[e-mail]
www.croydex.com
5/16” or 7/16”
(8mm or 11mm)
drill bit.
5
4
6
7
8

7. 8.
5. 6.
Mark centre of bottom hole.
Using a spirit level adjust the cabinet so it is level. When level accurately mark a hole in the centre of
the bottom xing hole using the bottom bracket as
a guide.
Drill an appropriate hole for the xing
to be used in the centre mark . Then
insert the wall plug or the toggle
bolt assembly. If using the wall plug,
ensure it is inserted ush to the wall
surface. If tting to a tiled surface, the
wall plug should be inserted below the
surface of the tile to avoid cracking the
tiles.
Screw the bottom bracket and spacer in position
as shown, (image 1). Do not overtighten! If the
cabinet is not level, loosen the screw and adjust
until it is level. The slot will allow for adjustment.
Then screw the locking cap to the bottom bracket
and t the cover, (see image 2).
Page 4 CAB 140 R07
Image 1
Image 2
5/16” or 7/16”
(8mm or
11mm)
123
6
4
7
58

9. 10.
12.11.
Additional top xings are supplied if required and
these can be xed with wall plugs or toggle bolts.
See images above for assembly details.
Assemble the shelf by inserting it into the carcass
at an angle, (image 1) then locating the front edge
into the side notches, (image 2). Push the tabs at
the back of the shelf into the indentations on the
back of the cabinet carcass to secure in place.
Attach the pin handle
to the underside of the
door(s) as shown.
Page 5
Image 1
Image 2
CAB 140 R07
UK: Croydex, Central Way, Andover,
Hampshire, SP10 5AW, UK
EU: MIL, Unit 8 Purcellsinch Ind Est, Dublin
Road, Kilkenny, R95 HP71, Ireland
[phone]
[phone]
[e-mail]
www.croydex.com
5/16” or 7/16”
(8mm or
11mm)
123
6
4
7
5
8
8
8 8 NOTE: WC4516## & WC4518## come
supplied with one shelf only.

CAB 140 R07
13.
Croydex, Central Way, Andover,
Hampshire, SP10 5AW, UK
[phone]
[phone]
[e-mail]
www.croydex.com
Page 6