Croydex WC257022 User manual

Thank you for purchasing this Croydex product. Please follow the fixing and care instructions to ensure
that your bathroom product is fitted safely and that it retains its high quality finish. Please retain this
leaflet for future reference.
This instruction leaflet applies to the following product:
WC257022 (White) Double Door Cabinet
Fixing Pack Contents
(a) 8 x Fixing screws
(b) 1 x Magnetic catch
(c) 4 x Magnetic catch Screws
(d) 4 x Mirrored door pivot pins
(e) 8 x screw caps
(f) 1 x Glue sachet
(g) 7 x Wooden dowels
(h) 4 x Shelf supports
(i) 2 x Wall fixing screws
(j) 2 x Wall plugs
(k) 2 x Washers
(l) 2 x Magnetic door plate
(m) 2 x Magnetic door plate screws
(n) 2 x Pivot pin bush
Tools Required
Drill; 6mm Masonry Drill Bit; 6mm Ceramic Drill Bit (optional); Cross Head Screwdriver; Large Flat Head
Screwdriver; Bradawl; Pencil, Spirit Level.
KEEP DIY TOOLS OUT OF THE REACH OF CHILDREN
Home Safety Advice
•It is recommended that two people fit the cabinet to ensure that it is fitted safely.
•Always take care when using an electric drill, particularly in the bathroom. Always check for
hidden cables and pipe work before drilling and take extreme care if there is any water in the
working area.
•It is advisable to use a residual current circuit breaker (RCCB).
•Always wear suitable eye protection when drilling.
•If the product is to be fitted on a ceramic tiled wall, a ceramic drill bit should be used. Always
ensure that the drill hole passes through the central tiled area rather than through the grouted
area. To prevent unnecessary damage to the tile, mask the area around the hole with tape
before drilling.
•Do not strike the product with hard or sharp objects.
•Do not overload the cabinet. Maximum safe working load is 10kg evenly distributed if mounted
on to a solid wall. If mounted on to a cavity wall reduce the load to 5kg evenly distributed.
Component Key
(a) Mirrored Doors, (b) Strengthening Baton, (c) Backing Board, (d) Side Panel, (e) Side Panel,
(f) Top Panel, (g) Base Panel, (h) Shelf.
(n)

Assembly Instructions
Lay out all components so they are all clearly identifiable prior to assembly.
Remove excess adhesive with a damp cloth before it dries.
Support the doors during assembly and do not allow the doors to fall open, as this will damage the hinge.
Product Care
To retain the best quality finish, clean product regularly with a soft cloth and mild detergents. Do not use
abrasive or chemical cleaners, as these will damage the product.
Do not slam the door open against its mechanical limits, as this will damage the hinge.
For details of other items in the Croydex range please visit our website: www.croydex.com
Croydex, Central Way, Andover, Hants, SP10 5AW, UK CAB 023 R08
2. Secure side panel to base using
two fixing screws. (Screws mounted
from underside of base. To improve
strength place small amount of glue
on underside of side panel before
securing into position.)
3. Place four wooden dowels into the
strengthening baton. Align the
dowels and locate into side panel.
(Wooden dowels must be glued into
position.)
1. Mount the magnetic door catch
onto the top panel. Use all four
magnetic catch screws.
4. Place the second side panel onto
the wooden dowels protruding from the
strengthening baton and secure side
panel to base panel using two fixing
screws. (To improve strength place
small amount of glue on underside of
side panel before securing into
position. Mount screws from underside
of base.) Slide the backing board into
the two recesses evident on the two
sidewalls. Locate into the base panel.
6. Place two of the door pivot pins
into the hole recesses situated on
the base. (The pivot pin bush’s
needs to be located in the recess
before inserting the pivot pins.)
Locate mirrored doors onto pivot
pins and place the remaining pivot
pins into the top of the door before
securing the top panel.
7. Place top panel onto cabinet
carcase ensuring all screw holes,
recesses, pivot pin bush’s and dowels
are accurately aligned with
assembled cabinet. Secure top panel
to both side panels with the four
remaining fixing screws. (To improve
strength place small amount of glue
to top of side panels before securing
the top panel.) Important: Please
allow the glue to dry prior to fitting
the cabinet.
8. Hold the cabinet against the wall in
its desired location and check that it is
straight and level. Open the door(s)
and mark the wall using the holes in
the back of the cabinet as a guide.
Drill 40mm deep holes in marked
positions using a 6mm masonry drill
and insert wall plugs. Align the holes
in the back of the cabinet with the wall
plugs. Insert the screws through the
washers and holes in the back of the
cabinet and screw in position.
9. Insert shelf supports into hole
recesses and ensure all supports
are aligned accurately. Place the
shelf in the cabinet and lower onto
the shelf supports. (Doors not
shown.)
5. Place the three remaining
wooden dowels into the top of the
strengthening baton. (Wooden dowel
must be glued into position.)