CTS IPS-3006 Series User manual

IPS-3006 SERIES
Industrial PoE Ethernet Switch
IPS-3006SFP-DR
4 Ports 10/100/1000Base-T plus 2 Ports 100/1000Base-X
Industrial PoE Ethernet Switch
IPS-3006SFP-F1-DR
5 Ports 10/100/1000Base-T plus 1 Port 100/1000Base-X
Industrial PoE Ethernet Switch
IPS-3006TP
6 Ports 10/100/1000Base-T Industrial PoE Ethernet Switch
User’s Guide
Version 0.91

2
Revision History
Version
Date
Description
0.90
20141119
First release
0.91
20151104
Revise series wiring connection
illustration Section 2.5

3
Trademarks
CTS is a registered trademark of Connection Technology Systems Inc.
Contents are subject to revision without prior notice.
All other trademarks remain the property of their respective owners.
Copyright Statement
Copyright 2014 Connection Technology Systems Inc.
This publication may not be reproduced as a whole or in part, in any way whatsoever unless
prior consent has been obtained from Connection Technology Systems Inc.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class-Adigital device,
pursuant to Part 15 of the FCC Rules. These limitations are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if the equipment is not installed and used in
accordance with the instructions, it may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult your local distributors or an experienced radio/TV technician for help.
Shielded interface cables must be used in order to comply with emission limits.
Changes or modifications to the equipment, which are not approved by the party responsible for
compliance, could affect the user’s authority to operate the equipment.
Copyright © 2014 All Rights Reserved.
Company has an on-going policy of upgrading its products and it may be possible that
information in this document is not up-to-date. Please check with your local distributors for the
latest information. No part of this document can be copied or reproduced in any form without
written consent from the company.
Trademarks:
All trade names and trademarks are the properties of their respective companies.

4
Table of Contents
1. OVERVIEW...................................................................................................5
1.1 Specification...............................................................................................5
1.2 Panel Layout...............................................................................................6
2. INSTALLATION ..........................................................................................10
2.1 Installation Requirements...........................................................................10
2.2 Checking the Package Contents...................................................................10
2.3 Installing the Industrial PoE Ethernet Switch................................................ 11
2.4 Wiring the Redundant Power Inputs ............................................................12
2.5 Wiring the Alarm Contact...........................................................................13
2.6 Connecting the switch to Network...............................................................14
3. OPERATION................................................................................................15
3.1 LED Definitions........................................................................................15
3.2 DIP Switch Definitions ..............................................................................15
4. MAINTENANCE..........................................................................................16
4.1 Fault Identification ....................................................................................16
4.2 Hardware Replacement Procedures .............................................................16

5
1. OVERVIEW
Thank you for choosing the IPS-3006 series Industrial PoE Ethernet Switches.
IPS-3006 series Industrial PoE Ethernet Switches are designed to meet the massive
needs for Gigabit and Fast Ethernet network deployments and aim at industrial
applications that demand wide range of operating temperature. They are fully compliant
with IEEE802.3, 802.3u, 802.3x, 802.3ab, 802.3z, 802.3x and 802.3at standards.
Besides, redundant power supplies are both offered on IPS-3006 series Industrial PoE
Ethernet Switches for users to create a reliable and stable network in the event of power
failure. By employing Store-and-Forward switching mechanism, the switch provides
low latency and faster data transmission.
1.1 Specification
Interface
1. IPS-3006SFP-DR
LAN Ports: 10/100/1000BASE-T x 4, PoE/PSE
WAN Ports: 100/1000BASE-X x 2
2. IPS-3006SFP-F1-DR
LAN Ports: 10/100/1000BASE-T x 4, PoE/PSE
WAN Ports: 100/1000BASE-X x 1 + 10/100/1000BASE-T x 1
3. IPS-3006TP
LAN Ports: 10/100/1000BASE-T x 4, PoE/PSE
WAN Ports: 10/100/1000BASE-T x 2
Standards
Comply with IEEE 802.3, 802.3u, 802.3ab, 802.3z, 802.3x and 802.3at
standards
Features
Switching:
Support Auto-Negotiation in TP ports
Support MDI/MDIX Auto-Crossover in TP ports
Full/Half Duplex Mode Operation
MAC Address Table: 2K
Store-and-Forward Switching Mechanism
Cable Specifications
The following table contains various cable specifications for the Industrial PoE
Ethernet Switch. Please make sure that you use the proper cable when connecting the
Industrial PoE Ethernet Switches.

6
Cable Type
Description
10BASE-T
UTP Category 3, 4, 5 (100 meters max.)
EIA/TIA- 568 150-ohm STP (100 meters max.)
100BASE-TX
UTP Cat. 5 (100 meters max.)
EIA/TIA-568 150-ohm STP (100 meters max.)
1000BASE-T
UTP Cat. 5e (100 meters max.)
UTP Cat. 5 (100 meters max.)
EIA/TIA-568B 150-ohm STP (100 meters max.)
100BASE-FX
Multi-mode fiber module(2km) / Single-mode fiber module
1000BASE-SX
Multi-mode fiber module (550m)
1000BASE-LX
Single-mode fiber module (10km)
1000BASE-LH
Single-mode fiber module (30km/50km)
1000BASE-ZX
Single-mode fiber module (80km)
Mini-GBIC
SFP Transceiver for 1000BASE-SX Multi-mode fiber module
(550m)
SFP Transceiver for 1000BASE-LX Single-mode fiber module
(10km)
SFP Transceiver for 1000BASE-LH Single-mode fiber module
(30km/50km)
SFP Transceiver for 1000BASE-ZX Single-mode fiber module
(80km)
1.2 Panel Layout
Front Panel
Figure 1. Front Panel for 4 Ports 10/100/1000Base-T + 2 ports 100/1000Base-X
➊
➋
➌

7
Figure 2. Front Panel for 5 Ports 10/100/1000Base-T + 1 port 100/1000Base-X
Figure 3. Front Panel for 6 Ports 10/100/1000Base-T
➊10/100/1000Mbps RJ-45 LAN ports, PoE/PSE
➋10/100/1000Mbps RJ-45 port(s) or 100/1000Mbps SFPport(s)
➌LEDs (for more information, please see chapter 3.1)
➊
➊
➋
➋
➌
➌

8
Rear Panel
Figure 4. Rear Panel
DIN-Rail metal spring (for more information, please see chapter 2.3)
Top Panel
Figure 5. Top Panel
➎Reset Button:
Insert a pin or paper clip to press the Reset Button for 5 seconds to
restart the system
Insert a pin or paper clip to press the Reset Button for 10 seconds to
reset the device back to factory defaults.
➏Terminal blocks (for more information, please see chapter 2.4)
➏

➐
➎
➑

9
➐Ground wire screw (for more information, please see chapter 2.3)
➑DIPSwitch (for more information, please see chapter 3.2)

10
2. INSTALLATION
To properly install the Industrial PoE Ethernet Switch, please follow the procedures
listed below. Procedures covered in this chapter are described below in separate
sections.
Installation Requirements
Unpacking the Industrial PoE Ethernet Switch
Installing the Industrial PoE Ethernet Switch
Powering on the Industrial PoE Ethernet Switch
Connecting the Industrial PoE Ethernet Switch to the Network
2.1 Installation Requirements
ATTENTION
Be sure to power off before installing or wiring your Industrial PoE
Ethernet Switch.
Be sure to calculate the maximum possible current in each power
wire and common wire. If the current goes above the maximum
ratings, the wiring could overheat, causing serious damage to your
equipment.
Be sure to read and follow below important guidelines :
Do not run signal or communications wiring and power wiring through the
same wire conduit. Wires with different signal characteristics should be
routed separately to avoid interference.
It is recommended that wiring which shares similar electrical characteristics
can be bundled together.
Keep input wiring and output wiring separate and label the wiring to all
devices in the system if necessary.
2.2 Checking the Package Contents
Unpack the package carefully and check the package contents. The package should
contain the following items:
Items included in standard package:
1 Industrial PoE Ethernet Switch
1 Documentation CD

11
If any of the above items is found missing or damaged, please contact your local sales
representative for support or replacement.
2.3 Installing the Industrial PoE Ethernet Switch
ATTENTION
This product is intended to be mounted to a well-grounded mounting
surface, such as a metal panel.
DIN-Rail Mounting
STEP1 : Insert the top of the DIN-Rail
into the slot just below the metal spring
STEP2 : The DIN-Rail attachment unit
will be snapped into place as shown
Metal
Spring
DIN-Rail
DIN-Rail
Metal
Spring

12
Grounding the Industrial PoE Ethernet Switch
Grounding helps to limit the effects of noise due to electromagnetic interference (EMI).
Be sure to install the ground connection from the ground screw to the grounding
surface before connecting devices.
Figure 6. Grounding wire
2.4 Wiring the Redundant Power Inputs
The Industrial PoE Ethernet Switch can be used with DC power 48-54 VDC with 2
terminal blocks. The terminal blocks are located on the upper panel of the Industrial PoE
Ethernet Switch. Before powering the Industrial PoE Ethernet Switch, please make sure
that network cables and power cables are securely connected.
ATTENTION
Before connecting the Industrial PoE Ethernet Switch to the DC
power inputs, make sure the DC power source voltage is stable.
PWR1 and PWR2 power supply are two pairs of contacts on the terminal block
connectors for power redundancy purpose. The redundant power supply will take over
seamlessly when one power source is down to protect your device or network from the
loss of power. When you use only one power supply (no redundant power is available),
the LED Power/Port Status will flash in orange to alert the user.

13
STEP 1 :
Insert the negative/positive DC wires into the V-/V+
terminals.
STEP 2 :
Use a small flat-blade screwdriver to tighten the
wire-clamp screws on the front of the terminal block
connector.
STEP 3 :
Insert the plastic terminal block connector prongs into the
terminal block receptor, which is located on the IPS’s top
panel.
2.5 Wiring the Alarm Contact
The Industrial PoE Ethernet Switch has two sets of Alarm Contacts which are used to
detect both power faults and port faults. We will explain the meaning of the two sets of
contacts used to connect the Alarm Contact below.
If you have two Alarm Systems:
ALM1:
The two wires attached to the Fault contacts form an
open circuit when the IPS has lost power from one of the
DC power inputs.
ALM 2 :
The two wires attached to the Fault contacts form an
open circuit when one of the ports for which the
corresponding Port Alarm DIP Switch is set to ON be
not properly connected.
If you have only one Alarm System:
(series connection)
The two wires attached to the Fault contacts form an
open circuit when :
The IPS has lost power from one of the DC power
inputs.
AND
One of the ports for which the corresponding Port Alarm
DIP Switch is set to ON be not properly connected.

14
(parallel connection)
The two wires attached to the Fault contacts form an
open circuit when :
The IPS has lost power from one of the DC power
inputs.
OR
One of the ports for which the corresponding Port Alarm
DIP Switch is set to ON be not properly connected.
2.6 Connecting the switch to Network
Connect to Network
This Industrial PoE Ethernet Switch has 2 uplink ports (RJ-45 or SFP, please refer to
ordering information) and 4 downlink 10/100/1000Mbps PoE/PSE RJ-45 ports for you
to implement it in your industrial environment. All RJ-45 ports can be inserted by
10/100/1000Base-T cables, connecting to the end devices. The fiber port(s) can accept
any kind of connector with proper SFP transceiver (mini-GBIC).
Figure 7. Industrial PoE Ethernet Switch general application

15
3. OPERATION
The Industrial PoE Ethernet Switch is Plug & Play compliant. Real-time operational
status can be monitored through a set of LED indicators located on the front panel.
3.1 LED Definitions
LED
Definition
Color
Operation
PWR1
Power
Off
Device is powered down.
Green
Device is powered up.
PWR2
Power
Off
Device is powered down.
Green
Device is powered up.
STATUS
Ethernet Port
Link Down
Alarm Status
Orange
Alarm is currently present
Off
No alarm is currently present
LINK/ACT
1~6
Port Status
Off
Port link is down
Green
Link is up and works at 10 or 100Mbps.
Green
Blinking
Receiving and transmitting data.
Orange
Link is up and works at 1000Mbps.
Orange
Blinking
Receiving and transmitting data.
PoE
Port PoE
Status
Green
PoE port connected to PD
Green
Blinking
PoE port link down and no any PD device
connected.
3.2 DIP Switch Definitions
Pin NO.
Function
OFF
ON
1
Port 1 Ethernet Port Link Down Alarm
Disable
Enable
2
Port 2 Ethernet Port Link Down Alarm
Disable
Enable
3
Port 3 Ethernet Port Link Down Alarm
Disable
Enable
4
Port 4 Ethernet Port Link Down Alarm
Disable
Enable
5
Port 5 Ethernet Port Link Down Alarm
Disable
Enable
6
Port 6 Ethernet Port Link Down Alarm
Disable
Enable

16
4. MAINTENANCE
It is easy to use and maintain this Industrial PoE Ethernet Switch. The procedures are
suggested when you want to identify faults or perform hardware replacement.
4.1 Fault Identification
Identifying faults can greatly reduce the time required to find the problem and solution.
Users may perform local or remote checks to find the problems.
Local Check
Users can perform local checks by observing LED indicators status.
When the whole system fails to function,
Check Power LED status
Check Power connection
Reset power
When certain network link fails to function,
Locate the port of the switch
Check Port Link Status LED
Check cable connection between the port and the connected device
Reset power
4.2 Hardware Replacement Procedures
ATTENTION
The Industrial PoE Ethernet Switch contains no user-serviceable
parts. DO NOT, UNDER ANY CIRCUMSTANCES, open and
attempt to repair it.
Failure to observe this warning could result in personal injury or
death from electrical shock.
Failure to observe the above warning will immediately void any
Warranty.