CTS HES-3106 Series User manual

HES-3106 SERIES
6 PORTS 10/100/1000BASE-T MANAGED ETHERNET SWITCH
5 PORTS 10/100/1000BASE-T AND 1 PORT 1000BASE-X OR
100/1000BASE-X UPLINK MANAGED ETHERNET SWITCH
5 PORTS 10/100/1000BASE-T AND 1 PORT 1000BASE-X OR
100/1000BASE-X UPLINK MANAGEMENT ETHERNET SWITCH
WITH CATV RF MODULE
User’s Guide
Version 1.0

2
Trademarks
CTS is a registered trademark of Connection Technology Systems Inc..
Contents subject to revision without prior notice.
All other trademarks remain the property of their respective owners.
Copyright Statement
Copyright 2012 Connection Technology Systems Inc..
This publication may not be reproduced as a whole or in part, in any way whatsoever
unless prior consent has been obtained from Connection Technology Systems Inc..
FCC Warning
This equipment has been tested and found to comply with the limits for a Class-A digital
device, pursuant to Part 15 of the FCC Rules. These limitations are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if the
equipment is not installed and used in accordance with the instructions, it may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult your local distributors or an experienced radio/TV technician for help.
Shielded interface cables must be used in order to comply with emission limits.
Changes or modifications to the equipment, which are not approved by the party
responsible for compliance, could affect the user’s authority to operate the equipment.
Copyright © 2012 All Rights Reserved.
Company has an on-going policy of upgrading its products and it may be possible that
information in this document is not up-to-date. Please check with your local distributors
for the latest information. No part of this document can be copied or reproduced in any
form without written consent from the company.
Trademarks:
All trade names and trademarks are the properties of their respective companies.

3
Table of Contents
1. INTRODUCTION ...........................................................................................4
1.1 The Managed Ethernet Switch.................................................................4
1.2 Appearance..............................................................................................5
2. INSTALLATION .............................................................................................8
2.1 Installation Requirements.........................................................................8
2.2 Checking the Package Contents..............................................................8
2.3 Installing the Managed Switch..................................................................9
2.4 Powering ON............................................................................................9
2.5 Connecting the Switch to Network..........................................................10
3. OPERATION................................................................................................ 11
3.1 LED Definitions....................................................................................... 11
4. MAINTENANCE ..........................................................................................12
4.1 Fault Identification ..................................................................................12
4.2 Hardware Replacement Procedures ......................................................13
4.3 Firmware Upgrade..................................................................................13

4
1. INTRODUCTION
Thank you for choosing this Managed Ethernet Switch. The Managed Switch
can provide the best performance and price ratio when multiple copper ports
need to be deployed in networking environment.
1.1 The Managed Ethernet Switch
With 5 or 6 10/100/1000Mbps RJ-45 ports on the front panel, this compact
Managed Switch provides high performance store-and-forward switching
capability plus other advanced features such as QoS, VLAN, etc.. Clear,
at-a-glance per-port LED indicators make it easier for users to control and
manage network status. The built-in management module also allows users to
configure, control and monitor the system via SNMP based management
system.
Specification
Interface
LAN Ports: 10/100/1000BASE-T x 5
WAN Port: 1000 or 100/1000BASE-X x 1 or 10/100/1000BASE-T x 1
Standards
Comply with IEEE 802.3, 802.3u, 802.3ab, 802.3z, 802.1q, 802.1p
standards
Features
Switching:
Support Auto-Negotiation in TP ports
Support MDI/MDIX Auto-Crossover in TP ports
Full/Half Duplex Mode Operation
MAC Address Table: 2K
Store-and-Forward Switching Mechanism
VLANs: Support up to 128 VLAN Groups
Support Tag VLAN
Support Q-in-Q VLAN
Support IGMP Snooping V1 and V2
Bandwidth Control
QoS support 802.1p and ToS Classification
Priority Queues: 4 Queues

5
Management:
Telnet/SSH/SNMP/Web interface
Storm Control
DHCP Client
DHCP Auto-Provisioning
Text Based Config
SFF-8472 (digital diagnostic management interface for SFP)
Power Down Trap
RMON:
FTP/TFTP upgrade
1.2 Appearance
Front Panel
Figure 1. Front Panel for 6 Ports 10/100/1000Base-T Managed Ethernet Switch
Figure 2. Front Panel for 5 Ports 10/100/1000Base-T and 1 Port 1000Base-X or 100/1000Base-X Uplink
Managed Ethernet Switch with CATV RF Module
➊Smart Lighting Control:
System Status LED and Port Link LEDs will be turned off by
pressing the button. Only Power LED indicator stays on.
➋10/100/1000Mbps RJ-45 ports
➌CATV RF Output (optional)
➊
➋
➌

6
Rear Panel
Figure 3. Rear Panel for 6 Ports 10/100/1000Base-T Management Ethernet Switch
Figure 4. Rear Panel for 5 Ports 10/100/1000Base-T and 1 Port 1000Base-X or 100/1000Base-X Uplink
Management Ethernet Switch with CATV RF Module
100/1000Mbps or 1000Mbps F/O Port
➎CATV Fiber Input (optional)
Left and Right Panel
Figure 5. Left Panel
Figure 6. Right Panel
➏Power Jack Connector
➐Reset Button:
Insert a pin or paper clip to press the Reset Button for 5 seconds
to restart the system
Insert a pin or paper clip to press the Reset Button for 10
seconds to reset the device back to factory defaults.
➎

➏
➐

7
Top Panel
Figure 7. Top Panel
➑LED: For detail definitions, please refer to chapter 3.1 LED Definitions
Cable Specifications
The following table contains various cable specifications for the Managed
Switch. Please make sure that you use the proper cable when connecting the
Managed Switch.
Cable Type
Description
10BASE-T
UTP Category 3, 4, 5 (100 meters max.)
EIA/TIA- 568 150-ohm STP (100 meters max.)
100BASE-TX
UTP Cat. 5 (100 meters max.)
EIA/TIA-568 150-ohm STP (100 meters max.)
1000BASE-T
UTP Cat. 5e (100 meters max.)
UTP Cat. 5 (100 meters max.)
EIA/TIA-568B 150-ohm STP (100 meters max.)
100BASE-FX
Multi-mode fiber module(2km) / Single-mode fiber module
1000BASE-SX
Multi-mode fiber module (550m)
1000BASE-LX
Single-mode fiber module (10km)
1000BASE-LH
Single-mode fiber module (30km/50km)
1000BASE-ZX
Single-mode fiber module (80km)
Mini-GBIC
SFP Transceiver for 1000BASE-SX Multi-mode fiber module (550m)
SFP Transceiver for 1000BASE-LX Single-mode fiber module (10km)
SFP Transceiver for 1000BASE-LH Single-mode fiber module
(30km/50km)
SFP Transceiver for 1000BASE-ZX Single-mode fiber module (80km)
➑

8
2. INSTALLATION
To properly install the Managed Switch, please follow the procedures listed
below. Procedures covered in this chapter are described below in separate
sections.
Installation Requirements
Unpacking the Managed Switch
Installing the Managed Switch
Powering on the Managed Switch
Connecting the Managed Switch to the Network
2.1 Installation Requirements
Basic requirements for installation are as follows:
Environmental conditions
One power outlet
Proper ventilation
Proper isolation to electrical noise, radio, etc..
UTP cables should not run in the same duct with power and
phone line cables
Required SFP Transceivers or UTP cables
2.2 Checking the Package Contents
Unpack the package carefully and check the package contents. The package
should contain the following items:
Items included in standard package:
1 Managed Switch
1 Documentation CD
1 Power Adaptor
If any of the above items is found missing or damaged, please contact your local
sales representative for support or replacement.

9
2.3 Installing the Managed Switch
CAUTION
To prevent any damage or failure of the Managed Switch, please DO NOT
block the ventilation FAN holes.
Use the following guidelines when choosing a place to install the Switch:
Firm and steady flat surface.
The location of power outlet should not be far away from the device.
Make sure that there is proper heat dissipation from and adequate
ventilation around the switch. Do not place heavy objects on the
Managed Switch.
Make sure water and moisture cannot enter the case.
Keep the cabling away from electrical noise.
2.4 Powering ON
The Managed Switch can be used with AC power adapter 100-240 VAC Input
and 12VDC output. The input connector is located on the left panel of the
Managed Switch. Before turning on the Managed Switch, please make sure that
network cables and power cables are securely connected.
Procedures:
1. Plug one end of the power adaptor into the power jack on the left
panel.
2. Plug the other end of the power adaptor into the power outlet. After
the power is on, the Power LED indicator should light in green.
Power Failure
In the event of power failure, unplug the power that is plugged into the switch at
the left of the device. Whenpower is resumed, plug the power back to the switch.
Please note that the Managed Switch has no Power ON/OFF Button. Therefore,
the only way to power on or power off the switch is to connect or disconnect the
power adaptor.

10
2.5 Connecting the Switch to Network
Connect to Network
This Managed Switch has 5 or 6 10/100/1000Mbps RJ-45 ports on the front
panel. These ports can be inserted by 10/100/1000Base-T cables, connecting to
the end devices. The connection of the fiber port on the rear panel must be
matched, i.e. Transmitter to Receiver and vice versa.
Figure 4. Example of segmenting network configuration

11
3. OPERATION
The Managed Switch is Plug & Play compliant. Real-time operational status
can be monitored through a set of LED indicators located on the top panel. A
built-in management module provides users with flexible interfaces to configure,
control and monitor the complete system remotely.
3.1 LED Definitions
LED
Definition
Color
Operation
POWER
Power
Off
Device is powered down.
Green
Device is powered up.
STATUS
System
Status
Orange
System is booting up.
Green
System is working normally.
Orange
Blinking
When the system is set back to default factory
setting, the Status LED indicator will blink 3
times in orange.
When the system is restarted, the Status LED
indicator will blink once in orange.
WAN
WAN Port
Status
Off
Port link is down
Green
Link is up and works at 100Mbps.
Green
Blinking
Receiving and transmitting data.
Orange
Link is up and works at 1000Mbps.
Orange
Blinking
Receiving and transmitting data.
LAN 1~5
LAN Port
Status
Off
Port link is down
Green
Link is up and works at 10 or 100Mbps.
Green
Blinking
Receiving and transmitting data.
Orange
Link is up and works at 1000Mbps.
Orange
Blinking
Receiving and transmitting data.

12
4. MAINTENANCE
It is easy to use and maintain this Managed Switch. The procedures are
suggested when you want to identify faults, perform hardware replacement and
firmware upgrading.
4.1 Fault Identification
Identifying faults can greatly reduce the time required to find the problem and
solution. Users may perform local or remote checks to find the problems.
Local Check
Users can perform local checks by observing LED indicators status.
When the whole system fails to function,
Check Power LED status
Check Power connection
Reset power
When certain network link fails to function,
Locate the port of the switch
Check Port Link Status LED
Check cable connection between the port and the connected device
Reset power
Remote Check
Users may check the Managed Switch through SNMP manager remotely. For
detailed procedures, please refer to the Network Management User’s Manual.

13
4.2 Hardware Replacement Procedures
WARNING!
The Managed Switch contains no user-serviceable parts. DO NOT, UNDER
ANY CIRCUMSTANCES, open and attempt to repair it.
Failure to observe this warning could result in personal injury or death
from electrical shock.
Failure to observe the above warning will immediately void any Warranty.
4.3 Firmware Upgrade
This Managed Switch may perform firmware upgrading when required. New
firmware can be obtained from your sales representative. For detailed upgrading
procedures, please refer to the Network Management User’s Manual.