Cudy GS1024 User manual

Package Contents CE Mark Warning
EU declaration of conformity
Safety Information
This is a Class A product. In a domestic environment, this product
may cause radio interference, in which case the user may be
required to take adequate measures.
Cudy hereby declares that this device is in compliance with the
essential requirements and other relevant provisions of directives
2014/30/EU, 2014/35/EU, 2009/125/EC and 2011/65/EU.
The original EU declaration of conformity may be found at
http://www.cudytech.com/ce.
1. Keep the device away from water, fire, humidity or hot environ-
ments.
2. Do not attempt to disassemble, repair, or modify the device.
3. Place the device with its bottom surface downward.
Please read and follow the above safety information when
operating the device. We cannot guarantee that no accidents or
damage will occur due to improper use of the device. Please use
this product with care and operate at your own risk.
Safety Precautions
To avoid any device damage and bodily injury caused by improper use,
you should observe the following rules.
Safety Precautions
1. Keep the power off during the installation.
2. Wear an ESD-preventive wrist strap, and make sure that the wrist
strap has a good skin contact and is well grounded.
3. Use only the power cord provided with the switch.
4. Make sure that the supply voltage matches the specifications
indicated on the rear panel of the switch.
5. Ensure that the switch is installed in a well-ventilated environment
and its ventilation hole is not blocked.
6. Do not open or remove the cover of the switch.
7. Before cleaning the device, cut off the power supply. Do not clean it
by the waterish cloth, and never use any other liquid cleaning method.
8. Place the device with its bottom surface downward.
One Switch One Power Cord
This Installation Guide Two mounting brackets, eight
screws and four rubber feet
Quick Installation Guide
Model: GS1016/GS1024
Quick Installation Guide
Model: GS1016/GS1024
www.cudytech.com
[email protected]
Company: Shenzhen Cudy Technology Co., Ltd 810600047

Specification
Figure 3-3 Rack Installation
Rack
Caution:
1. Leave 5 to 10 cm gaps around the devices for air circulation.
2. Avoid placing heavy things on the device.
3. Mount devices in sequence from the bottom to top of the rack and
ensure a certain clearance between devices for the purpose of heat
dissipation.
3. After the brackets are attached to the device, use suitable screws (not
provided) to secure the brackets to the rack, as illustrated in the following
figure.
Model
Standards
Number of Ports
Network Media (Cable)
Transfer Method
Switching Capacity
Packet Forwarding Rate
Packet Buffer
MAC Address Table
Jumbo Frame
LED indicators
Power Supply
Power Consumption
Dimensions ( W x D x H )
Environment
GS1016 / GS1024
IEEE 802.3、IEEE 802.3u、IEEE802.3ab、
IEEE802.3x、IEEE802.3az
16 x 10/100/1000Mbps Auto-Negotiation ports
24 x 10/100/1000Mbps Auto-Negotiation ports
10Base-T: UTP category 3,4,5 cable (maximum 100m)
100Base-Tx: UTP category 5,5e cable (maximum 100m)
1000Base-T:UTP category 5e,6 cable (maximum 100m)
Store-and-Forward
32Gbps / 48Gbps
23.81Mbps / 35.7Mbps
4.1Mbit
8K
9KByte
10M/100M Link/ACT：Orange
1000M Link/ACT：Green
Power ：Green
AC 100-240V/50-60Hz 12V/1.5A internal power
Maximum: 15W(220V/50Hz)
440*140*44mm
Operating Temperature: 0℃~40℃
Storage Temperature: -40℃~70℃
Operating Humidity: 10%~90% RH non-condensing
Storage Humidity: 5%~90% RH non-condensing
Appearance
LED Explanation
Installation
Front Panel
The front panel of GS1016 is shown as the following figure.
Power
10/100M Orange
1000M Green
GreenON
OFF -
Figure 1-1 Front Panel of GS1016
GS1016
16-Port Gigabit Ethernet Switch
10/100/1000Mbps
RJ45 Port
LEDs
The front panel of GS1024 is shown as the following figure.
Figure 1-2 Front Panel of GS1024
10/100/1000Mbps
RJ45 Port
GS1024
24-Port Gigabit Ethernet Switch
LEDs
Figure 3-1 Desktop Installation
Rack-mounting Bracket
Screw
Rack Installation
To install the device in an EIA standard-sized, 19-inch rack, follow the
instructions described below:
1. Check the efficiency of the grounding system and the stability of the rack.
2. Secure the supplied rack-mounting brackets to each side of the device
with supplied screws, as illustrated in the following figure.

 

 

 

 


Feet
Bottom of the Device
Notch
1 3
2
Desktop Installation
LINK/ACT Figure 3-2 Bracket Installation