Curt Manufacturing 11065 User manual

PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE ALL FASTENERS ARE TIGHT AND ALL STRUCTURAL COMPONENTS ARE SOUND
CURT Manufacturing Inc. warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective, Curt Manufacturing Inc. may repair or replace
the product at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. Curt Manufacturing Inc.'s liability is limited to repair or replacement
of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.
For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com
MAKE: STYLE:
MIN.
20
WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY
WEIGHT CARRYING:
INSTALLATION TIPS:INSTALLATION TIME:
INSTALLATION REQUIRES:
VEHICLE PHOTO:
HITCH ILLUSTRATION:
REPRESENTATIVE PHOTO
MAKE SURE YOUR HITCH MATCHES
LEVEL OF DIFFICULTY:
EASY
EASY MODERATE HARD
THE INSTALL TIME LISTED IS FOR PROFESSIONAL
INSTALLERS. IF YOU ARE HESITANT TO UNDERTAKE
THIS TASK ON YOUR OWN, CONTACT AN AUTHORIZED
CURT INSTALLER FOR ADDITIONAL ASSISTANCE.
1. BEFORE YOU BEGIN INSTALLATION, READ ALL
INSTRUCTIONS THOROUGHLY.
2. TO EASE INSTALLATION, 2 PEOPLE MAY BE
REQUIRED.
3. USING PROPER TOOLS WILL GREATLY IMPROVE
THE QUALITY OF THE INSTALL AND REDUCE THE
TIME REQUIRED.
4. NEED HELP OR HAVE SOME QUESTIONS?
CALL TECHNICAL SUPPORT AT 800.798.0813
Safety glasses should be
worn at all times while
installing this product
.
YEARS: 2010 VOLVO MODEL: C70 CONVERTIBLE
2,000
200
TRAILER WEIGHT:
TONGUE WEIGHT:
11065 INSTALLATION INSTRUCTIONS
LBS.
LBS.
12/10/2012
WARNING:
WE RECOMMEND THE USE OF 18050 STABILIZING STRAPS FOR ALL NON-TRAILER
(WHEEL-LESS) LOADS. PLEASE SEE THE CURT CATALOG OR VISIT US ONLINE AT
WWW.CURTMFG.COM FOR FURTHER INFORMATION.
RATCHET SOCKET
10mm
3/4"
TORQUE
WRENCH
SAFETY
GLASSES
WIRE PIPE
BRUSH
LOWER EXHAUST
WELDNUT CLEANING
MAY BE REQUIRED
NO DRILLING REQUIRED

INSTALLATION WALKTHROUGH:
For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com
Parts List
DESCRIPTION
PART NUMBER
QTY
ITEM
HEX BOLTM8-1.25 x 3541
CONICAL TOOTHED WASHER3/8"
4
2
CARRIAGE BOLT1/2-13 x 1 1/223
.250 x 1.00 x 2.00" SQUARE HOLE SPACERCM-SP122
4
HEX FLANGE NUT
HFN 121325
EXISTING WELDNUTS (BOTH SIDES)
EXHAUST HANGER BRACKET (BOTH SIDES)
DRIVER SIDE FRAME RAIL
PASSENGER SIDE FRAME RAIL
EURO MOUNT OPTION AVAILABLE
#45591 (1 7/8" BALL) AND #45592 (2" BALL)
DESIGNED FOR
USE WITH
BALLMOUNT #45522
1
2
3
4
5
1. Lower exhaust by removing (2) M8 fasteners from each
exhaust hanger bracket. Return (4) M8 fasteners to vehicle
owner.
2. Raise hitch into position. (NOTE: Hitch will be sandwiched
between frame and exhaust hanger brackets)


INSTALLATION WALKTHROUGH:
For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com
3. Loosely attach hitch to vehicle tie down brackets using the
supplied 1/2" hardware and SP12 spacers, as shown.
4. Secure exhaust hanger brackets and hitch to frame using
the supplied M8 fasteners and 3/8" conical tooth washers.
5. Torque all M8 fasteners to 24 ft-lbs and all 1/2" hardware
to 110 ft-lbs.
6. Install is complete.

GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.
***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.***
WARNING: ALL NON-TRAILER LOADS APPLIED TO THIS PRODUCT MUST BE SUPPORTED BY 18050 STABILIZING STRAPS.
** FAILURE TO PROPERLY SUPPORT NON-TRAILER LOADS WILL VOID PRODUCT WARRANTY**
HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-800-798-0813
HITCH WEIGHT: LBS.
INSTALL TIME
PROFESSIONAL: MINUTES
NOVICE (DIY): MINUTES
INSTALL NOTES:
INSTALLATION STEPS
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS
ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.
Curt Manufacturing Inc., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,
Curt Manufacturing Inc., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of
this product voids the warranty. Curt Manufacturing Inc.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or
consequential loss or damage.
2,000 200
32
20
VOLVO C70
10/19/2012
11065
40
Parts List
DESCRIPTIONPART NUMBERQTYITEM
HEX BOLTM8-1.25 x 3541
CONICAL TOOTHED WASHER3/8"
42
CARRIAGE BOLT1/2-13 x 1 1/2
23
.250 x 1.00 x 2.00" SQUARE HOLE SPACERCM-SP1224
HEX FLANGE NUTHFN 121325
TOOLS REQUIRED
RATCHET
10mm & 3/4" SOCKETS
TORQUE WRENCH
1. Lower exhaust by removing (2) M8 fasteners from each exhaust hanger bracket. Return (4) M8 fasteners to
vehicle owner.
2. Raise hitch into position and loosely attach it to vehicle tie down brackets using the supplied 1/2" hardware
and SP12 spacers, as shown above. (NOTE: Hitch will be sandwiched between frame and exhaust hanger
brackets)
3. Secure exhaust hanger brackets and hitch to frame using the supplied M8 fasteners and 3/8" conical tooth
washers.
4. Torque all M8 fasteners to 24 ft-lbs and all 1/2" hardware to 110 ft-lbs.
EURO MOUNT OPTION AVAILABLE
#45591 (1 7/8" BALL) AND #45592 (2"BALL)
DESIGNED FOR
USE WITH
BALLMOUNT #45522
-NO DRILLING REQUIRED
-LOWER EXHAUST
VEHICLE TIE
DOWN BRACKET
(BOTH SIDES)
EXHAUST HANGER BRACKET (BOTH SIDES)
PASSENGER SIDE FRAME RAIL
DRIVER SIDE FRAME RAIL
EXISTING WELDNUTS (BOTH SIDES)
4
3
5
2
1