Curv Smart Alarm System User manual

Curv Smart Alarm System
Instructions

TOP View
Bottom View
1 Box contents
2 Design
-Alarm Control Panel x1
-Pet Sensitive PIR Motion Sensor x4
-Door/Window Contact x2
-Remote Controls x4
-RFID Tags x4
-Internal x1 & External Siren x1
-Documentation
CLEAR SOS DISARMARM
LCD
CALL
RFID READER/WIFI LED
HOME MODE
WIFI CONNECTION
Adapter interface
Power On/O

3 Features
-Works with GSM and Internet Connection (Wi-Fi Connection)
-Supports up to 10 remote controls, 60 wireless accessories and 30 RFID
tags
-Can store up to 5 phone numbers & 5 SMS numbers
-Arm / disarm the system by SMS, phone call, or App (on iOS or Android)
-Notifications sent in case of alert and system status change
-SIM card slot: stay connected even where you don’t have an Internet
connection or when your home Wi-Fi network is down (SIM card not
included)
-Audio surveillance of the site from distance
-Can be disarmed by RFID tag
-Built-in siren (95dB)
-600mAh lithium batteries included for more than 8hours standby
mode.
4 Specifications
Product name
Curv Smart Alarm System
SKU
CURV-ALR01
Power Supply
Input: AC 110-240V / 50-60 Hz
Output: DC 12V / 1A
Wi-Fi
2.4GHz 802.11 b/g/n
GSM- frequency
GSM:850 / 900 / 1800 / 1900 MHz
Radio-frequency
433/868MHz
Transmission distance
< 80M in open space
Backup batteries
Lithium Batteries: 7.4V / 600 mAh
Internal siren
95dB
Housing material
ABS plastic
Operating conditions
Temperature: -10°C~55°C
Humidity: ≤ 80% (non-condensing)
Control panel dimensions (L x W x H)
188 x 125 x 25 mm

Run the APP Register Interface
Create Family Device Interface
5 Get your APP ready
5.1 Download APP “Curv Smart” on your smart phone.
The app is available on the App Store and Google Play.
5.2 Run and install the APP on your smart phone.
5.3 Register by your Mobile number/e-mail address.
5.4 Login and create a family.

Device List Interface Enter Wi-Fi Password
Connect the Alarm to Servers Set Alarm’s Name
6 Connect the Alarm to your APP
6.1 Reset the WiFi: Disarm the system→Type Admin Code:123456 & select
"Enter".Go to the settings menu→choose “WIFI Config”→choose
"Connecting", then press "Enter"button to start the network setting.
The following steps are to be carried out on the app
6.2 Add Device: choose “Add Device”→”Others”→”Wi-Fi Connector”.
6.3 Enter the password of the Wi-Fi network (Your router’s password that
the APP was connected with), wait for about 20 seconds for a response.
6.4 Now you can set the alarm name to complete the connection.

Device List Interface Operation Interface
Settings Interface Accessories Interface
7 APP Operation Interface

Important
-Make sure the SIM card is not protected by a PIN code.
-Insert the SIM card when your Alarm is turned o.
-We advise you to choose a plan with unlimited text and 1 or 2 hours of
call. The SIM card must be compatible with the GSM network. Contact
your carrier for more information.
8 Use Alarm system with SIM card
You will need a SIM card if you wish to use your Alarm system with SMS
and phone calls.
8.1 Insert the SIM card in the control panel.
8.2 Plug the AC adapter to the DC Jack.
8.3 Turn on the Power switch.

When your system is armed, all detectors are active.
By app
Connect to your alarm and click on “Arm”.
By remote control
Press on the “Arm” button of the remote control .
On the control panel
Click Arm button.
By SMS
Send 1 to the phone number of the SIM card in the control panel.
(Only saved SMS numbers can disarm the system by SMS.)
9 Connect wireless accessories
10 Daily use
Arm the system
When your system is armed in Home mode, all detectors are active
except those assigned to the Home zone.
By app
Connect to your alarm and click on “Home mode”.
Arm in Home mode
9.1 By the keypad:
--Enter the settings menu, type Admin code123456+ Enter button;
--Choose “Accessories”→”RFID Tag”/”Remote control”/”Wireless
sensor”→”Add a new”;
9.2 By the APP: Connect to the alarm, choose the wireless accessory→
click “+” ADD.
9.3 Trigger the accessory which will be connected, you will hear one
beep: the accessory is registered. If the control panel beeps twice, the
detector was already connected.
9.4 Repeat step1 or 2, then step3 for next accessory.

By remote control
Press on the “Home” button of the remote control .
On the control panel
Click Home mode button.
By SMS
Send 2 to the phone number of the SIM card in the control panel.
(Only saved SMS numbers can disarm the system by SMS.)
Disarm the system
When your system is disarmed, all detectors are inactive except
those assigned to the 24H zone.
By app
Connect to your alarm and click on “Disarm”.
By remote control
Press on the “Disarm” button of the remote control .
On the control panel
User code1234+ Disarm button.
By SMS
Send 0 to the phone number of the SIM card in the control panel.
(Only saved SMS numbers can disarm the system by SMS.)
SOS function
The SOS function enables you to trigger your alarm immediately.
By remote control
Press on the “SOS” button of the remote control.
On the control panel
Press and hold the SOS(#) button on the control panel.

11 Control by phone call
This function enables you to control your alarm system by phone
call. This can especially be helpful if you are located in an area
without Wi-Fi or 3G/4G coverage.
This function applies only if you are using the Alarm system with a
SIM card.
How it works
1. Call the phone number of the SIM card in the control panel.
2. The control panel picks up: type your 4-digit passcode, followed
by “#” (Default passcode: 1234).
3. A voice prompt conrms if your code is correct.
4. On your phone, dial the code corresponding to the command:
Table 1
Dial
1
0
*
3
6
9
#
Command
Arms the system
Audio monitoring
Two-way talk
Turns the siren o
Turns the siren on
Disarms the system, turns the siren o and ends the
phone call
- Disarms the system and turns the siren o
- Stops monitoring without hanging up
If your alarm is triggered
If the alarm is triggered, your control panel will immediately
inform you:

12 Reset Wi-Fi
If you want to connect the alarm to your APP or change the network
of the alarm, you need reset the Wi-Fi to factory settings to enable
the function.
13 Restore Admin Code
Turn the control panel on. Press the tamper switch at the back of
the control panel 5 times within 5 seconds after having turned it on.
The Admin code will be restored to the factory settings:123456.
This operation is only for user forgot his admin code, The stored
phone numbers, system settings and connected accessories will
not be changed.
At home
-The built-in siren starts ringing out.
-If you have connected additional sirens, they start ringing out too.
On your smartphone(if your alarm is connected to your Wi-Fi
network)
- You receive a push notification in the Curv Smart app (you must
have an Internet access on your smartphone).
On your smartphone (with a SIM card in the control panel)
-The control panel sends an SMS notication to every SMS number saved.
-The control panel calls every Phone number saved. If you take that call,
you can decide to stop the siren, disarm the system or other functions
as listed below, by dialing the corresponding code in Table1.
Operation : Type Admin Code:123456+Enter button to the settings
menu→choose “WIFI Cong”→choose “Connecting”, then press
“Enter” button to start the network setting.

To prevent re or shock hazards, do not expose this product to rain or
moisture. Apparatus shall not be exposed to dripping or splashing and
no object lled with liquids, such as vases, shall be placed on the
apparatus.
Warning
ATTENTION
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE,
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert the user to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sucient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
product.

Standards
This product bears the selective sorting symbol for waste electrical
and electronic equipment (WEEE). This means that this product must
be handled pursuant to European Directive 2012/19/EU in order to be
recycled or dismantled to minimize its impact on the environment.
For further information, please contact your local or regional authorities.
Electronic products not included in the selective sorting process are
potentially dangerous for the environment and human health due to the
presence of hazardous substances.
In compliance with European laws. This product is in compliance with
the essential requirements and other relevant provisions of Directive
2014/53/EU.
This product was designed and manufactured in compliance with
Directive 2011/65/EU of the European Parliament and of the Council on
the restriction of use of certain hazardous substances in electrical and
electronic equipment (RoHS Directive - RoHS) and is deemed to comply
with the maximum concentration values set by the European Technical
Adaptation Committee (TAC).
Manufactured in China.