Curv360 MS-06B User manual

MS-06B

1. General information
2. Design
The signal of the MS-06B is transmitted by radiofreq-
uency, which makes its installation easier.Several
MS-06B can be installed in indoor locations to deter
illegal intrusions. Several MS-06B canbe registered in
the control panel of your alarm system. When your
alarm system detects an intrusion, the MS-06B rings
out and its strobe lights turn on.
The MS-06B can also be used as a standalone alarm
system by registering wireless accessories in the siren.

3. Power ON/OFF the Siren
4. Enter/exit connection mode
Note: the connection mode enables connect with the
control panel and wireless accessories.
Power ON: press and hold the power switch until lights
on, the siren is on.
Power OFF: press and hold the power switch until lights
off, the siren is off.
Enter connection mode: short press the connection
button, the Blue LED will be light on.
Exit connection mode: re-press the connection button
to exit.
Power Switch
Setting
Connection

Note: Do not trigger any sensor when registering the
siren in the control panel.
Test
Press the “Arm” button on the control panel. The built-
in speaker of the control panel beeps and the Red LED
of the MS-06B blinks every 5 seconds: the connection is
successful. If not, the connection has failed, try
registering the siren again.
5. Use as an additional siren
How to connect the siren with the control panel
1. Enter connection mode: short press the connection
button on the side of the siren, the Red LED will be
light on: you are now in connection mode for 20
seconds.
2. Trigger the control panel: press any of the “Arm” or
“Home mode” buttons on the control panel of your
alarm system.
3. Connection successfully: you hear short beeps, the
siren has been registered in the control panel
successfully.
If the siren is used as an additional siren, it must be
registered to your alarm control panel. If the alarm is
triggered, the MS-06B will ring out and its LED lights
will turn on.

Test
Press the “Arm” button of the remote control. The Red
LED of the MS-06B blinks every 5seconds: the connection
is successful. Trigger a sensor that is already connected
to the siren, the siren will ring out. If not, the connection
has failed, try registering the siren again.
6. Use as a standalone alarm system
How to connect the siren with a wireless sensor
1. Enter connection mode: short press the connection
button on the side of the siren, the Red LED will be
light on: you are now in connection mode for 20
seconds.
2. Trigger the control panel: Trigger the accessory (e.
g. press any button on the remote if you want to
connect a remote control).
3. Connection successfully: you hear short beeps, the
accessory has been connected to the siren
successfully. The siren supports up to 20 wireless
accessories.
The MS-06B can be connected to wireless accessories
to be used as an independent alarm system. When the
system is armed, if a sensor is triggered, the siren will
ring out and the strobe lights will turn on.

7. Set Siren alert time
Short press the Setting button to set siren duration
time to 1/2/3 minutes.
8. Reset
It is recommended to reset the siren if you were lose
one of the accessory, especially if you have lost your
remote control.
Regardless the system is armed or disarmed, press and
hold the connection button until you hear 5 beeps (5
seconds): all accessories or control panels connected
have been cleared from the siren.
9. Specifications
Power supply :AC 90V~ 240V/50-60Hz
Backup battery: 3.7V, 300mAh Li-polymer
Static current:< 15mA
Alarm current:< 260mA
Volume: 90 dB
Radio frequency: 433MHz
Working distance: upto 80m in open space
Housing material: ABS plastic
Operating conditions
Temperature: 0°C ~ +50°C
Relative Humidity: ≤80%(non-condensing)
Dimensions: 70 x 70 x 70 mm