CyberData 011214 Manual

Quick Reference 931560F © 2022, CyberData Corporation, ALL RIGHTS RESERVED© 2022, CyberData Corporation, ALL RIGHTS RESERVED 931560F Quick Reference
Gooseneck Mounting
Contacting CyberData
Ground Wire
Network Cable
(Sold separately)
Weather Shroud
Backbox
Torx security screw
Faceplate mounting
Torx key
SIP Outdoor Intercom with Keypad
(4 sets included)
Carriage Bolt
Gooseneck
Cable & Wire
Create service loop
Apply RTV Silicone Sealant around mounting holes and
backside perimeter of Backbox and Weather Shroud
Carriage Bolt, Washer & Nut
(All Cables, Fasteners, Sealant and Gooseneck are not provided
(Apply Blue Loctite on threads)
unless noted otherwise.)
J1 to J1
GENERAL ALERT
Caution
Equipment Hazard: Do not use an electric
or power screwdriver to fasten the face plate
and PCB assembly to the gang box. To prevent
over-torque damage to the gasket, do not apply
more than 10 inch-pounds force. Over-torquing
will cause the gasket to tear, risk moisture intrusion,
and effectively void the manufacturer's warranty.
Note: To mount the intercom, use methods
compliant with local electrical codes.
Note: More installation and mounting
information is illustrated in the Operations Guide.
011215 Outdoor Shroud, 2X
Sales: 831-373-2601 ext. 334
Support: 831-373-2601 ext. 333
Support Website: https://support.cyberdata.net/
RMA Department Contact and Status: https://support.cyberdata.net/
Warranty Information: https://support.cyberdata.net/
Corporate Headquarters
CyberData Corporation
3 Justin Court
Monterey, CA 93940, USA
Phone: [phone]
Fax: [phone]
https://www.cyberdata.net/
Typical System Installation
Getting Started
• Download the Operations Guide PDF file, from the Downloads tab at the following webpage:
https://www.cyberdata.net/products/011214
• Create a plan for the locations of your devices.
• WARNING: This product should be installed by a licensed electrician according to all local electrical and building codes.
• WARNING: To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation
instructions.
• WARNING: The PoE connector is intended for intra-building connections only and does not route to the outside plant.
• WARNING: This enclosure is not rated for any AC voltages!
Parts
Parameter Factory Default Setting
IP Addressing DHCP
IP AddressaIPv4 Link Local
Web Access Username admin
Web Access Password admin
Subnet MaskaIPv4 Link Local
Default GatewayaIPv4 Link Local
a. Default if there is not a DHCP server present.
802.3af Compliant Ethernet Switch
Intercom IP Phone IP PBX ServerIntercom Intercom
*More installation and mounting
options are available in the
Operations Guide.
Accessory Kit
Mounting Component
(1) 1/2-inch EMT
compression
connector with extra
sealing locknut
(1) 531085* Hole
plug assembly
(4) Carriage bolts
(4) Carriage bolt nuts
(4) Carriage bolt washers
(6) Security Torx Screws
Security Torx Key
(6) Phillips Screws
Optional Accessories
(for gooseneck mounting)
Optional Accessories Sold Separately
Installation Quick Reference
SIP Outdoor Intercom with Keypad
SIP Compliant
011214
The IP Endpoint Company

© 2022, CyberData Corporation, ALL RIGHTS RESERVED 931560F Quick Reference Quick Reference 931560F © 2022, CyberData Corporation, ALL RIGHTS RESERVED
Terminal Block Connections
RTFM Button
Call Button
7.480 [190.00]
Dimensions are in Inches [Millimeters]
2.284 [58.01]
5.118 [130.00]
5.198 [132.03]
Microphone
Hole
Speaker
Drain Hole
Features Dimensions (Front and Side View)
1
8
Wire (IN)
Tin Leads
Approx. 1/4” or
6mm
Terminal Block
can accept 16 AWG wire
Alternate Power Input:
1 = +8 to +12VDC @ 1000mA Regulated Power Supply*
2 = Power Ground*
Relay Contact:
(1 A at 30 VDC for continuous loads)
3 = Relay Common
4 = Relay Normally Open Contact
5 = Sense Input
6 = Sense Ground
7 = Remote Switch "A"
8 = Remote Switch "B"
*Contacts 1 and 2 on the terminal block are only for
powering the device from a non-PoE 12VDC power
source as an alternative to Network PoE power. Use of
these contacts for any other purpose will damage the
device and void the product warranty.
34
Use a 3.17 mm (1/8-inch) flat blade
screwdriver for the terminal block screws
RTFM button (SW1)
When the device is operational and linked to a network, you
can use the Reset Test Function Management (RTFM) but-
ton (SW1 [see picture]) to announce the device’s IP
address or restore the device to the factory
default settings.
To announce the device’s current IP address:
• Press and release the RTFM button within a five
second window.
Note The device will use DHCP to obtain the new IP
address (DHCP-assigned address or default to
IPv4 Link Local if a DHCP server is not present).
To restore the device to factory default settings:
• Press and hold the RTFM button for longer than five
seconds until you hear the device announce that it is
restoring the factory default settings.
Dimensions (Rear View and Mounting Holes)
Wall Mounting
0.000 [0.00]
0.869 [22.07]
2.559 [65.00]
4.249 [107.93]
5.118 [130.00]
0.000 [0.00]
2.050 [52.07] 3.740 [95.00]
5.430 [137.93] 7.480 [190.00]
Ø0.280 [Ø7.11]
(4 Places)
Ø0.876 [Ø22.25]
Dimensions are in inches [millimeters]
Conduit
Ground Wire
Network Cable
1/2" EMT
Compression
connector
1/2" EMT
anchor screw
1/4"
1/4" Concrete
(Sold separately)
Weather Shroud
Wall Anchor
Torx key
SIP Outdoor Intercom with Keypad
through side Conduit Hole
Network and Ground cables
Cables
create service loop
Apply RTV Silicone Sealant Around Mounting Holes and
Backside Perimeter of Backbox and Weather Shroud
with
sealing locknut
(Sold separately)
Torx security screw
Faceplate mounting
(All Cables, Fasteners, Sealant and Gooseneck are not provided
unless noted otherwise.)
with Compression connector
Remove hole plug assembly then
Install it onto the rear conduit hole
*
*
J1 to J1
Note: For flush mount installations, purchase the 011442 Flush
Mount Kit, 2x (sold separately). For more information, go to:
https://www.cyberdata.net/products/011442
Note: To mount the device, use methods
compliant with local electrical codes.
Note: More installation and mounting information
is illustrated in the Operations Guide.
Caution
Equipment Hazard: Do not use an electric or power screwdriver to fasten the face plate and PCB assembly to
the gang box. To prevent over-torque damage to the gasket, do not apply more than 10 inch-pounds force.
Over-torquing will cause the gasket to tear, risk moisture intrusion, and effectively void the manufacturer's
warranty.
GENERAL ALERT
011215 Outdoor Shroud, 2X