CyberData 011309 Manual

Quick Reference 930925D © 2017, CyberData Corporation, ALL RIGHTS RESERVED© 2017, CyberData Corporation, ALL RIGHTS RESERVED 930925D Quick Reference
Typical System Installation
Getting Started
• Download the Operations Guide PDF file, from the Downloads tab at the following webpage:
http://www.cyberdata.net/voip/011309/
• Create a plan for the locations of your Intercoms.
• WARNING: This product should be installed by a licensed electrician according to all local electrical and building codes.
• WARNING: To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation
instructions.
• WARNING: The PoE connector is intended for intra-building connections only and does not route to the outside plant.
• WARNING: This enclosure is not rated for any AC voltages!
Parts
Parameter Factory Default Setting
IP Addressing DHCP
IP Addressa
a. Default if there is not a DHCP server present.
10.10.10.10
Web Access Username admin
Web Access Password admin
Subnet Maska255.0.0.0
Default Gatewaya10.0.0.1
802.3af Compliant Ethernet Switch
IP Phone IP PBX ServerIntercom Intercom
*More installation and mounting
options are available in the
Operations Guide.
InformaCast Server
(1) Intercom
Assembly (1) Spacer for half-inch set conduit connector
(1) 531085B hole plug assembly
Optional Accessories
(for gooseneck mounting)
(1) T-15H Torx Key
(4) Security Torx Screw (4) Carriage bolts
(4) Carriage bolt nuts
(4) Carriage bolt washers
Optional Accessories
Connecting the Intercom (Service Loop Routing)
Securing the Intercom
Contacting CyberData
Creates Service Loop
Route Cable(s) inside Gang Box to
Creates Service Loop
Route Cable(s) inside Gang Box to
(Not Provided)
Ground Wire
Nut
Ground Lug
Ground Cable Installation Network Cable Installation
Ground Wire
(not provided)
Ground Lug
Nut (to Ground Lug
inside of the Gang Box
Route cable(s) inside of the
Gang Box to create the service loop.
Route cable(s) inside of the
Gang Box to create the service loop.
Network Cable
(not provided)
Torx Key
Torx Screws
Faceplate &
PCB Assembly
2 Gang Box
GENERAL ALERT
Note: To mount the intercom, use methods
compliant with local electrical codes.
Caution
Equipment Hazard: Do not use an electric or power
screwdriver to fasten the face plate and PCB assembly to the
gang box. To prevent over-torque damage to the gasket, do
not apply more than 10 inch-pounds force. Over-torquing
will cause the gasket to tear, risk moisture intrusion, and
effectively void the manufacturer's warranty.
Note: More installation and mounting
information is illustrated in the Operations
Guide.
Sales: [phone] ext. 334
Support: 831-373-2601 ext. 333
Support Website: http://support.cyberdata.net/
RMA Department: [phone] ext. 136
RMA Email: [email protected]
RMA Status: http://support.cyberdata.net/
Warranty Information: http://support.cyberdata.net/
Corporate Headquarters
CyberData Corporation
3 Justin Court
Monterey, CA 93940, USA
Phone: [phone]
Fax: [phone]
http://www.cyberdata.net/
The IP Endpoint Company
Installation Quick Reference
Singlewire InformaCast Outdoor Intercom
011309

© 2017, CyberData Corporation, ALL RIGHTS RESERVED 930925D Quick Reference Quick Reference 930925D © 2017, CyberData Corporation, ALL RIGHTS RESERVED
Dimensions (Rear View and Mounting Holes)
Terminal Block Connections
Call Button
Features Dimensions (Front and Side View)
Microphone
Hole
Speaker
Drain Hole
1.690
[85.85]
0.869 [22.07]
0.869 [22.07]
3.380 [85.85]
1.690
[42.93]
[42.93]
3.380
Dimensions are in Inches [Millimeter]
ø0.280 [ø7.11]
ø0.854 [ø21.69]
(4 Places)
0.25"
Terminal Block
Wire (IN)
can accept 16 AWG wire
1
8
Alternate Power Input:
1 = +8 to +12VDC @ 1000mA Regulated Power Supply*
2 = Power Ground*
Relay Contact:
(1 A at 30 VDC for continuous loads)
3 = Relay Common
4 = Relay Normally Open Contact
5 = Sense Input
6 = Sense Ground
7 = Remote Switch "A"
8 = Remote Switch "B"
*Contacts 1 and 2 on the terminal block are only for
powering the device from a non-PoE 12VDC power
source as an alternative to Network PoE power. Use of
these contacts for any other purpose will damage the
device and void the product warranty.
34
Use a 3.17 mm (1/8-inch) flat blade
screwdriver for the terminal block screws
RTFM Button
Conduit Mounting Restrictions (Side Entry)
Conduit Mounting Restrictions (Rear Entry)
When the device is operational and linked to a network,
you can use the Reset Test Function Management
(RTFM) button (SW1 [see picture]) to announce the
device’s IP address or restore the device to the factory
default settings.
To announce the device’s current IP address:
• Press and release the RTFM button within a five
second window.
Note The device will use DHCP to obtain the new IP
address (DHCP-assigned address or default to
10.10.10.10 if a DHCP server is not present).
To restore the device to factory default settings:
• Press and hold the RTFM button for longer than five
seconds until you hear the device announce that it is
restoring the factory default settings.
RTFM button (SW1)
Spacer
5/32"
(Not Provided)
1/2" Conduit
1/2" Set Screw
(Not Provided)
Connector
Assembly
Hole Plug
Network
Cable
(Not Provided)
Gap
*More installation and mounting
information is illustrated in the
Operations Guide.
1/2" Conduit
(Not Provided)
Here Connector
1/2" Conduit
(Not Provided)
Cable
Network
Spacer
Add
(Not Provided)
Cable
Network
(Not Provided)
1/2" Conduit
1/2" Conduit
Spacer Connector
(Not Provided)
(Not Provided)
Here
Add
With Shroud Without Shroud