Cycle Torch SHARK 300 User manual

1
User Manual EN
SHARK 300

2
Thank you for purchasing one of our products !!!
We are truly honored to be able to serve you and provide you with the best
Experience possible. If you’ve enjoyed our product, we would sincerely appreciate
your honest feedback.
To insure maximum experience and safety, familiarize yourself with ALL
aspects of your new light and battery system:
I. Safety Precaution ..........................................................................................3
II. How to mount SHARK 300 to a Bicycle .........................................................3
III. How to charge SHARK 300.............................................................................4
IV. Switching the lighting modes ........................................................................5
V. Model Specifications......................................................................................6
VI. Non-Rechargeable Tail Light .........................................................................6
VII. Warranty, Support and Customer Service ....................................................7
I.
II.
III.
IV.
V.
VI.
VII.
If for any reason you are not satisfied, please contact us as soon as
possible at: [e-mail] , so that we can work with you to
solve whatever issues!

3
I. Safety Precaution
1. Never look directly into bike light;
2. Avoid directing the light beam into the eyes of another person;
3. Do not place it within children’s reach;
4. Before your trip, please make sure that the light is firmly mounted to the
handlebar, it lights up, and the light is not blocked by baggage;
5. This product is waterproof under normal daily use and can be used in the
rain. However, do not intentionally submerge it in water.
Failure to follow these cations may expose you to risks, can cause
damage to the light system and will void the warranty !
A lighting system can make riding safer and you more visible, but lights are no
substitute for common sense. Ride within your capability with consideration for
the riding environment.
This product contains components that must be recycled per EU Directive
2002/96/EC and may not be disposed as unsorted municipal waste!
ll. How to mount SHARK 300 to a Bicycle:
1. Attach the rubber strip to one end of the light bracket;
2. Hold the light with one hand and with another hand secure it with the rubber
strip across the handlebar;
3. For further details, click the link and watch the VIDEO.
I.
II.
III.
IV.
V.
VI.
VII.

4
III. How to charge SHARK 300
1. Remove the rubber cap at the bottom of light;
2. Connect the light to your PC, or a 5V USB battery charger with the USB cable.
The switch lights up, and charging starts.
3. When the switch turns blue, charging is complete. Remove the USB cable.
Tips and tricks:
1. When your PC is in sleep state, the light cannot be charged;
2. Flashing light of the switch shows that a charging error has occurred. Remove
and reinsert the USB cable, then begin the recharge process again;
3. The battery charges to about 80% after approximately 4 hours;
4. Charging and lighting times are approximate values, and will vary by
environmental and user conditions.
I.
II.
III.
IV.
V.
VI.
VII.
WARNING: The cable (or other accessories) supplied with the Cycle Torch bike
light MUST be used only to charge the Cycle Torch bike light. The Manufacture
or/and the Seller are not responsible for any damage caused by using the supplied
accessories with other devices, other than Cycle Torch bike lights.

5
IV. Switching the lighting modes
Operation Modes: The initial short press of the switch will turn the light on
High mode. Each additional short press of the button switches the light from one
mode to the next in the following order: (1) High; (2) Medium; (3) Low; (4) Flash
Turning off SHARK 300: Press and hold the button for one to three seconds.
Checking Battery Level: When the light is turned off, press the button for 3
seconds and release. The light will flash from 1 to 10 times indicating the remaining
battery level (10 flashes indicate - 100% charge, 9 flashes - 90%, 8 flashes –80% …).
Low Battery Level: The switch light will glow red when the battery level is low
and the light will automatically turn off when the battery level is too low. This
system protects the battery from damage, but since it draws a small amount of
current, and can drain the battery beyond the minimum voltage for the battery.
The light must be turned off when the button glows red or within 5 minutes
of it glowing red. Do not wait until the light goes completely out as this will greatly
reduce the number of charge cycles that the battery can be used and can render
the battery unusable.
Charge your bike light each 2-3 months when stored or not in use to prevent
battery degradation.
V. Model Specifications
Operating modes:
High
Medium
Low
Flash
Run time (in hours)
2,5
5
25
50
Power (in lumens)
300
150
30
300
I.
II.
III.
IV.
V.
VI.
VII.

6
Model range: SHARK 300 USB LIGHT,
Water-resistant headlamp Brightness: 300 LM
Waterproof Grade: IP65
Light Source: CREE XML T6 ultra bright LED
LED lifespan: 50,000 hours
Low power consumption
Battery: 1 x SAMSUNG 18650, 3.7V, 2400 mAh Li-ion
Charge time: 4 ~ 10 hours
Low Power warning: red light warning (blue fluorescent ring changes to red)
Battery discharge time:
-150 minutes in High mode (100 % or 300 lumens)
-300 minutes in Medium mode (50% or 150 lumens)
-1800 minutes in Low mode (10% or 30 lumens)
-3000 minutes in Flash mode (300 Lumens)
Material: high quality nylon plastic (ABS), weighing only 100g
Fluorescent waterproof indicator ring for greater night visibility
Finish: different colors available
VI. Non rechargeable Tail Light
Before turning on:
1. Unscrew the back cap & remove one Battery, remove the paper insert, place
the battery back, and assembly the light back (see the link);
2. Press the lens to turn ON the light;
3. Short Press will switch through cycles & shut down the Light;
4. For further details, click the link and watch the VIDEO.
I.
II.
III.
IV.
V.
VI.
VII.

7
Operation Modes: The initial short press of the switch will turn on the light
High. Each additional short press of the button switches the light from one mode
to the next, in the following order: (1) Steady; (2) Flash; (3) Slow Flash; (4) OFF.
Running time: 50 hours and more
Waterproof Grade: IP65
Included accessories: silicone strap which fits all standard seat posts.
VII. Warranty, Support and Customer Service
To register you product please go to http://cycletorch.com and follow the steps.
Our product quality is controlled strictly in accordance within the standards
of CYCLE TORCH quality certification program.
To ensure that all users enjoy the product, we offer one year warranty
within one year from purchase date, under normal use, the consumer will be
provided free warranty service for any quality related problems!
When requesting warranty service, customer should present Amazon Order
ID or numbers provided by online retailers.
Warranty Service Exclusions:
A) Any damages that are caused by other than normal use, including, but not
limited to physical damages.
B) Any user modification, repairs or disassembly of the product without
factory authorization.
C) Missing warranty Registration.
I.
II.
III.
IV.
V.
VI.
VII.
For further information concerning warranty conditions or for any
additional issues, please e-mail us at: [e-mail]