CYmodel CESSNA 310 User manual

SAFETY PRECAUTIONS
This radio control model is not atoy!
lFirst-time buildersshould seekadvice frompeople havingbuilding
experience inorder toassemble themodel correctlyand toproduce
its performanceto fullextent. ,
lAssemble thiskit onlyin placesout ofchildrens reach!
lTakeenough safetyprecautions priorto operatingthis model.
,
You areresponsible forthis modelsassembly andsafe operation!
lAlways keepthis instructionmanual readyat handfor quick
reference,even aftercompleting theassembly
lCould causeserious injuryor evendeath.
SPECIFICATION
Wing Span:3200 mm (126 in)
2
Wing Area:128.4dm(1990sq.in)
Total Length: 2165 mm (85.2 in)
Radio : 5 channels , 8 servos
Engine : 4C , 1.40 cu.in(a pair)
26cc gas(a pair)
CESSNA 310
ALMOST - READY - TO - FLYALMOST - READY - TO - FLY
Before commencing assembly,please read these instructions thoroughly.
Thank you for choosing CYmodel
Global : www.cymodel.com
Australia : www.austars-model.com
Italia : www.biellaexpress.com
Instruction Manual
Item Nr: CY8109
All manuals and user guides at all-guides.com
all-guides.com

REQUIRED FOR OPERATION (Purchase separately)REQUIRED FOR OPERATION (Purchase separately)REQUIRED FOR OPERATION (Purchase separately)REQUIRED FOR OPERATION (Purchase separately)
TOOLS REQUIRED ( Purchase separately)TOOLS REQUIRED ( Purchase separately)TOOLS REQUIRED ( Purchase separately)TOOLS REQUIRED ( Purchase separately)
BEFOREYOUBEGINBEFOREYOUBEGINBEFOREYOUBEGINBEFOREYOUBEGIN
SharpHobbyKnife Phillips Screw Driver Awl
NeedleNosePliers Wire Cutters Scissors
Read through the manual before you begin ,so you will have an overall idea of what to do.
Check all parts .if you find any defective or missing parts .contact your local deater.
Symbols used throughout this instruction manual,comprise.
111
222
333
.
.
Warning!
!
Do not overlook this symbol.
Aminimum 5channel radio for airplanes (with 8servos).
And dry batteries.
CAUTION: Only use a minimum 5channel radio for
airplanes! (No other radio may be used!)
!
12 AA-size Batteries
Aminimum 5 channel
transmitter for airplanes.
For handing the radio properly.refer to its instruction manual.
Engine and Muffler
Purchase a propeller that
will match your engine
Silicone Tube Fuel Filter
required for engine starting Glow engine fuel only.
WARNING: Normal gasoline cannot
be used with glow engines.
!
Fuel Pump Plug Wrench
Glue
Instant glue
Epoxy Glue
Other equipment for enhancing
airplane operation & perormance
12VBattery (for starter)
Engine Starter
BBBB
16X10----18X10
22
Cut off shaded portion.
Ensure smooth non-binding
movement while assembling.
Must be purchased
separately!
Pay close attention
here!
Drill holes with the specified
Diameter(here:2mm)
Assemble left and right
Sides the same way.
Apply instant glue
(CA glue,super glue).
Apply epoxy glue.
Cut off excess.
502
C.AC.A
LL
RR
AB2mm2mm
99
44
11
77
66
55
88
Muffler
Muffler
Ignition
Ignition
Model Airplaneengine:4c1.40-1.60cu.in(apair)
26ccgasengine(apair)
Receiver
22
Battery (need 3)
33
Servo(need 8 servos )
remote control
Switch (need 3)
AA
All manuals and user guides at all-guides.com

!
33
22
Assemble the wingtip
11
55
44
3
Install the aileron servo
Assemble the aileron and flap
Install the flap servo
The servo must be purchase separately!
It must be 90 size
Accessory list for this page.
Hinge
-----4
BA
BA
BA
2.5X100 mm Rod
Rod adjuster
Horn
Connecting rod head
- - - - - - 2
- - - - - - 4
- - - - 2
- - - - 2
2X10mm Screw
2.3X10mm Tp Screw
- - - - - - 12
- - - - - - 4
3X40mm Screw
- - - - - - 6
4X40mm Screw
- - - - - - 2
The servo must be purchase separately!
It must be 90 size
BA
2.5X45 mm Rod
Horn
Connecting rod head
3X12mm Tp Screw
2.3X10mm Tp Screw
- - - - - - 6
- - - - - - 12
- - - - 2
- - - - 2
Rod adjuster
- - - - - - 2
- - - - - - 4
4X40mm Screw
- - - - - - 2
2X10mm Screw
- - - - - - 4
Diameter
(here:4.2mm)
4.2mm
According the engine demand,
add high.
Assemble the engine mount
BA
Aileron
1mm trailing edge
Hinge
-----8
Hinge
2.5X100 mm Rod
Rod adjuster
Horn
Connectingrodhead
- - - - - - 4
- - - - - - 8
- - - - 2
- - - - 4
2X10mm Screw
2.3X10mm Tp Screw
- - - - - - 24
- - - - - - 8
3X40mm Screw
- - - - - - 6
4X40mm Screw
- - - - - - 4
2.5X45 mm Rod
- - - - 2
- - - - - - 4
3X12mm Tp Screw
- - - - - - 6
Horn
- - - - 2
- - - -8
Hinge
PVC canopy
here , installthe light
BA
12X65 tube
All manuals and user guides at all-guides.com

!
8
710
999
4
6
Accessory list for this page.
Tube
Main wing
1.8X400mm Rod
- - - - - - 2- - - - - - 2- - - - - - 2
Linkage Stopper
2mm Nut
- - - - 2- - - - 2- - - - 2
- - - - 2- - - - 2- - - - 2
3X3mm Screw
- - - - - - 2- - - - - - 2- - - - - - 2
Main wing
The throttle servos can
be a standard servos.
5X55mm Screw
- - - - 4
5mm Washer
- - - - - 4
Put the line into the wing,
then,into the main fuselage
Assemble the engine
After confirmingthe
position(see frontof
fuel tank).
Insert and tighten
the screw.
Assembly of the fuel tank
180mm
Fuel tank
Engine:
4C,1.40cu.in(a pair)
Assemble the engine
Engine:
26cc gas(a pair)
Down
Top
25X1120mm - - - 1
20X900mm - - - 1
Put the aileron line
and the flap line,
into the fuselage
8mm nylon Nut
- - - - - - 4
5X55mm Screw
- - - - 4
5mm Washer
- - - - - 4
1.8X400mm Rod
- - - - - 2- - - - - 2- - - - - 2
Linkage Stopper
2mm Nut
- - - - 2- - - - 2- - - - 2
- - - - 2- - - - 2- - - - 2
3X3mm Screw
- - - - - - 2- - - - - - 2- - - - - - 2
8mm nylon Nut
- - - - - - 4
All manuals and user guides at all-guides.com

!
13
12 15
14
11
Accessory list for this page.
Install the main landing gear.
AA
AA
=
B
B
B
B
B
B
=
Checking the wing
Securely glue together
,ifcoming off during flights.
You lose control of your airplane
whichleads to accidents!
Install the nose landing gear.
Three wheel retract system
pul out length of6mm
to make gear up
air valve
Make sure toassemble retracts asinstructed below
RetractsRetracts 3-way
pressure inlet
Air tank
Retracts
3-way
pressure inlet
Switch Air inlet
Warning!
Horizontal tail.
Hinge
----8
5X40mm Axletree
3X25mm Tp Screw
- - - - - - 4
5.2mm Collar
3X3mm Screw
- - - - - - 2
- - - - - - 1
4X3mm Screw
8mm tube
750mm steel wire
- - - - - - 2
- - - - - - 4
3X25mm Tp Screw
- - - - - - 8
5.2mm Collar
3X3mm Screw
- - - - - - 4 - - - - - - 2
4X3mm Screw
- - - - - - 2
This door can open
Here, use the nylon belt tie upHere, use the nylon belt tie upHere, use the nylon belt tie up
5X45mm Axletree
3X25mm Tp Screw
- - - - - - 12
- - - 2
5.2mm Collar
3X3mm Screw
- - - - - - 6
- - - - - 3
4X3mm Screw
- - - - - - 3
8mm tube
750mm steel wire
- - - - - - 2
- - - - - - 4
Hinge
-----8
- - - - - 1
- - - - - 1
5X45mm Axletree
- - - - - 2
5X40mm Axletree
- - - 1
BA
All manuals and user guides at all-guides.com

!
1818
1717 2020
1919
666
1616
Accessory list for this page.
Hinge
-----4
BA
3X20mm Screw
- - - - 4
- - - - - 4
Horizontal&Vertical tail.
Install the rudder
The servo must be purchase separately!
It must be 90 size
2.5X100 mm Rod
Rod adjuster
Horn
Connecting rod head
- - - - - - 2
- - - - - - 4
- - - - 2
- - - - 2
2X10mm Screw
- - - - - - 4
3X40mm Screw
- - - - - - 6
4X40mm Screw
- - - - - - 2
DD
=
C
C
=
Securely glue together
,if coming off during flights.
You lose control of your airplane
which leads to accidents!
Horizontal&Vertical tail.
EE
=
DD
C
C
EE
Rod 8mm tube
950mm steel wire
Rod adjuster
Horn
Connecting rod head
- - - - - - 2
- - - - - - 4
- - - - 2
2X10mm Screw3
- - - - - - 4
3X40mm Screw
- - - - - - 3
4X40mm Screw
- - - - - - 2
- - - - - - 8
- - - - - 4
- - - - - - 2
Clamp the
8 mm tube
Rod 8mm tube
950mm steel wire
Rod adjuster
Horn
Connecting rod head
- - - - - - 4
-- - - - - 8
- - - - 4
2X10mm Screw
- - - - - - 8
3X40mm Screw
- - - - - - 9
4X40mm Screw
- - - - - - 4
- - - - - - 8
- - - - - 4
- - - - - - 2
2.5X100 mm Rod
Horn
- - - - 2
- - - - 2
3X20mm Screw
- - - - 2
- - - - - 2
Hinge
Tuble:20X430mm -----1
3mm Nut
- - - - - - 3
3mm Nut
- - - - - - 3
8mm nylon Nut
- - - - 2
The servo must be purchase
separately!It must be 90 size
- - - - 4
8mm nylon Nut
- - - - 2
3mm Washer
Tuble:12X150mm -----1
Install the rudder servo
Install the elevator servo
3mm Washer
All manuals and user guides at all-guides.com
all-guides.com

!
2323
2222 2525
2424
2121
Accessory list for this page.
Assemble the canopy
Assemble the cowl
2.3X10 Tp screw
- - - - 4
Radio Equipment
ReceiverReceiverReceiver
BatteryBatteryBattery
Install the cover
Assemble the canopy
2.6X12Tp screw
- - - - - 12
2.3X10Tpscrew
- - - - - 4
2.6X12 Tpscrew
- - - - - 12
77
All manuals and user guides at all-guides.com

28
27 29
Side view
ELEVATOR
Adjust the travel of each control surface to the
values in the diagrams.
These values fit general flight capabilities.
Readjust according to your needs and flight level.
Top view
26
AILERON
Adjustment.
Adjust the travel of each control surface to the
values in the diagrams.
These values fit general flight capabilities.
Readjust according to your needs and flight level.
888
Adjustment.
Never fly before checking the Cg srequired position.
In order to obtain the CG specified ,reposition the
receiver and battery.
NEVER fly the model
without well balancing.
Warning!
!
CG
Side view
Rudder
Adjust the travel of each control surface to the
values in the diagrams.
These values fit general flight capabilities.
Readjust according to your needs and flight level.
Top view
140-145mm140-145mm140-145mm
Adjustment
Adjustment.
Side view
30
Top view
94mm94mm94mm
Falp
Side view
Spread adiagram
97mm
97mm
60mm60mm60mm
63mm63mm63mm
82mm
82mm
All manuals and user guides at all-guides.com