CYmodel Macchi MC-205 veltro User manual

Before commencing assembly,please read these instructions thoroughly.
SAFETY PRECAUTIONS
This radio control model is not a toy!
lFirst-time builders should seek advice from people having building
experience in order to assemble the model correctly and to produce
its performance to full extent.
,
lAssemble this kit only in places out of children s reach!
lTake enough safety precautions prior to operating this model.
,
You are responsible for this models assembly and safe operation!
lAlways keep this instruction manual ready at hand for quick
reference,even after completing the assembly.
lCould cause serious injury or even death
Macchi MC-205 veltro
ALMOST - READY - TO - FLYALMOST - READY - TO - FLY
SPECIFICATION
Wing Span:2485 mm (98 in)
2
Wing Area:79 dm (1225sq.in)
Total Length: 2075 mm (81.5 in)
Engine : 80-100cc gas engine
Radio : 6 channels ,9 servos

REQUIRED FOR OPERATION (Purchase separately)REQUIRED FOR OPERATION (Purchase separately)REQUIRED FOR OPERATION (Purchase separately)REQUIRED FOR OPERATION (Purchase separately)
TOOLS REQUIRED ( Purchase separately)TOOLS REQUIRED ( Purchase separately)TOOLS REQUIRED ( Purchase separately)TOOLS REQUIRED ( Purchase separately)
BEFORE YOU BEGINBEFORE YOU BEGINBEFORE YOU BEGINBEFORE YOU BEGIN
Sharp Hobby Knife Phillips Screw Driver Awl
Needle Nose Pliers Wire Cutters Scissors
Read through the manual before you begin ,so you will have an overall idea of what to do.
Check all parts .if you find any defective or missing parts .contact your local dealer.
Symbols used throughout this instruction manual,comprise.
111
222
333
.
.
Warning!
!
Do not overlook this symbol.
Aminimum 5channel radio for airplanes (with 8/9servos).
And dry batteries.
CAUTION: Only use a minimum 5channel radio for
airplanes! (No other radio may be used!)
!
12 AA-size Batteries
Aminimum 5 channel
transmitter for airplanes.
For handing the radio properly.refer to its instruction manual.
Engine and Muffler
Purchase a propeller that
will match your engine
Silicone Tube Fuel Filter
required for engine starting Glow engine fuel only.
WARNING: Normal gasoline cannot
be used with glow engines.
!
Fuel Pump Plug Wrench
Glue
Instant glue
Epoxy Glue
Other equipment for enhancing
airplane operation & perormance
12VBattery (for starter)
Engine Starter
BBBB
22
Cut off shaded portion.
Ensure smooth non-binding
movement while assembling.
Must be purchased
separately!
Pay close attention
here!
Drill holes with the specified
Diameter(here:2mm)
Assemble left and right
Sides the same way.
Apply instant glue
(CA glue,super glue).
Apply epoxy glue.
Cut off excess.
502
C.AC.A
LL
RR
AB
2mm2mm
99
44
11
77
66
55
88
Model Airplane engine:80-100cc gas engine
receiver
22
Battery (need 2)
33
Servo(need 8/9 servos )
remote control
Switch (need 2)
AA
Muffler

!
3
2
1
5
4
33
Install the aileron and flap
Install the servo of aileron
Install the servo
Aileron
Flap
Hinge
Hinge
Install the aileron and flap
Bottom view
Install the servo of flap
Hinge
Hinge
Accessory list for this page.
LL
RR
LL
RR
Securely glue together. If coming off during flights,you'll
lose control ofyour airplane whichleads to accidents!
Warning!Warning!
Rod adjuster
Connecting rod head
2X10mm screw
- - - - - 4
- - - - - 2
- - - - - 4
2.5X85mm rod
- - - - - 2
HORN
- - - - - 2
4X30 Screw
- - - - - 2
LL
RR
FlapAileron
AB
AB
- - - - - - - - 4
- - - - - - - - 8
A B
Make sure hingesare
mounted in thesame line
3mm3mm
3mm3mm
2.3X10mm Tp screw
- - - - - 8
LL
RR
Rod adjuster
Connecting rod head
3X35mm screw
2X10mm screw
- - - - - 4
- - - - - 2 - - - - - 6
- - - - - 4
2.5X85mm rod
- - - - - 2
HORN
- - - - - 2
- - - - - 2
4X30 Screw
- - - - - 2
2.3X10mm Tp screw
- - - - - 8
Flap Aileron
Tailing edge
Aileron
4mm
Servo line
Servo line
LL
RR
3X20mm screw
- - - - - 8
3X20mm screw
- - - - - 8
Rod adjuster
Connecting rod head
3X35mm screw
2X10mm screw
- - - - - 8
- - - - - 4
- - - - - 6
- - - - - 8
2.5X85mm rod
- - - - - 4
HORN
- - - - -4
- - - - - 2
4X30 Screw
- - - - - 4
2.3X10mm Tp screw
- - - - - 16
- - - - - - - - 4
- - - - - - - - 8

!
8
7
6
10
9
44
Accessory list for this page.
Install the elevator
LL
RR
Securely glue together. If coming off during flights,you'll
lose control ofyour airplane whichleads to accidents!
Warning!Warning!
LL
RR
Rod adjuster
Connecting rod head
3X25mm screw
2X8mm screw
- - - - - 4
- - - - - 2
- - - - - 6
- - - - - 4
2.5X85mm rod
- - - - - 2
HORN
- - - - - 2
- - - - - 2
4X30 Screw
- - - - - 2
Bottom view
Install the elevator
make sure hingesare
mounted in thesame line
AB
Hinge
- - - - - - - - 4
Install the elevator servos
Install the elevator servos
LL
RR
LL
RR
2.3X10mm Tp screw
- - - - - 8
3mm3mm
LL
RR
Install the rudder
make sure hingesare
mounted in thesame line
Hinge
- - - - - - - 4
A B
8mm8mm
8X60 tube
- - - - - - - 1
Servo line
Hinge
- - - - - - 8
8X60 tube
- - - - - 1
Rod adjuster
Connecting rod head
3X25mm screw
2X8mm screw
- - - - - 4
- - - - - 2
- - - - - 6
- - - - - 4
2.5X85mm rod
- - - - - 2
HORN
- - - - - 2
- - - - - 2
4X30 Screw
- - - - - 2
2.3X10mm Tp screw
- - - - - 8

!
13
12 15
1414
55
11
Accessory list for this page.
Install the rudder servos
Install the rudder
Install the tail wheel
Aluminium tube
Rod adjuster
2X10mm screw
- - - - - 4
- - - - - 4
Rod
- - - - - 4
- - - - - 4
Install the servos of rudder&tail wheel
Install the tail wheel
Securely glue together. If coming off during flights,you'll
lose control ofyour airplane whichleads to accidents!
Warning!Warning!
Tailing edge
Rudder
4mm
AB
Aluminium tube
Rod adjuster
Connecting rod head
2X10mm screw
- - - - - 2
- - - - - 2
- - - - - 2
Rod - - - - - 2
- - - - - 2
4X35mm screw
- - - - - 1
4mm nut
- - - - - 2
1400mm Steel wire
- - - - - 2
2.3X10Tp screw
- - - - - 4
1400mm Steel wire
- - - - - 2
Aluminium tube
Rod adjuster
2X10mm screw
- - - - - 2
- - - - - 2
Rod - - - - - 2
- - - - - 2
- - - - 1
- - - - 2
3.2mm Collar
3.2mm Nylon Collar
3X3mm Screw
- - - - 3
- - - - 3
6X9 screw
- - - - 1
- - - - 1
M3X20 Tp screw
3.2mm Rocker
- - - - - 1
6mm nut
Aluminium tube
Rod adjuster
Connecting rod head
2X10mm screw
- - - - - 8
- - - - - 2
- - - - - 8
Rod - - - - - 8
- - - - - 8
4X40mm screw
- - - - - 1
4mm nut
- - - - - 2
1400mm Steel wire
- - - - - 4
- - - - 1
- - - - 2
3.2mm Collar
3.2mm Nylon Collar
3X3mm Screw
- - - - 3
- - - - 3
6X9 screw
- - - - 1
- - - - 1
M3X20 Tp screw
3.2mm Rocker
- - - - - 1
6mm nut
2.3X10Tp screw
- - - - - 4

!
18
17 20
19
16
66
Accessory list for this page.
LL
RR
3X3mm screw
5.2mm Collar
3X20mm Tp screw
- - - - - 8
5X45mm Axletree
- - - - - 2
- - - - - 2
- - - - - 2
4X4mm screw
- - - - - 2
Air tank
Switch
Air inlet
3-way
pressure inlet
3-way
pressure inlet
3-way
pressure inlet
Quick release connector
Quick release connector
Pressure reduction inlet
Strut
Strut
Pleas notice the inner diameter for each
side of the pressure reduction inlet.
Please insure the sealing of the retract
system before flight . Retainer
Rod adjuster
2X8mm screw
- - - - - 1
- - - - - 1
- - - - - 1
Rod (1.8X80mm)
- - - - - 1
900 Air line
- - - - - 2
502502
C.AC.A
After glue the PVC cover,
cut off its excess part.
Plywood
- - - - - - - - - - - -4
Plywood
- - - - - - - - - - - -2
A B
Install the main landing gear
Install the main landing gear Main wing
(Put the servo into the fuselage)
Install the main landing gear
Install the main landing gear
8mm nylon Nut
- - - - - 2
5X30mm screw
- - - - 2
3X3mm screw
5.2mm Collar
3X20mm Tp screw
- - - - - 8
5X45mm Axletree
- - - - - 2
- - - - - 2
- - - - - 2
4X4mm screw
- - - - - 2
Plywood
- - - - - - -4
Plywood
- - - - - - - -2
8mm nylon Nut
- - - - - 2
5X30mm screw
- - - - 2
Retainer
Rod adjuster
2X8mm screw
- - - - - 1
- - - - - 1
- - - - - 1
Rod (1.8X80mm)
- - - - - 1
900 Air line
- - - - - 2

!
23
25
77
21 24
22
Accessory list for this page.
Horizontal
(Put the servo into the fuselage)
Main wing&Horizontal/Vertical tail
Securely glue together
,if coming off during flights.
You lose control of your airplane
which leads to accidents!
AA
B B
C C
4mm4mm
4X25mm screw
4mm Washer
- - - - - - - - 2
- - - - 2
A
A
B
B
C
C
Installing the engine (50-80cc)
After confirming the
position(see front of
fuel tank).
Insert and tighten
the screw.
Fuel supply line
Fuel pipe
Air pressure line
1.8X400mm Rod
- - - - - - 1
Linkage Stopper
2mm Nut
- - - - 1
- - - - 1
3X3mm Screw
- - - - - - 1
Install the throttle servo
Assembly of the full tank
175mm
ThrottleThrottle
1.8X400mm Rod
- - - - - - 1
Linkage Stopper
2mm Nut
- - - - 1
- - - - 1
3X3mm Screw
- - - - - - 1
4X25mm screw 4mm Washer
- - - - - - - - 2
- - - - 2
Fuel tankFuel tank

!
28
27 30
29
88
26
Accessory list for this page.
Radio Equipment
Install the thr cowling
ReceiverReceiver
Battery/IgnitionBattery/Ignition
Install the canopy
Install the canopy
3mm Washer
- - - - - 2
3X30mm screw
- - - - - 2
3mm rubber band
- - - - 2
2.3X10mm Tp screw
- - - - - 8
3mm Bind nut3mm Bind nut
3mm Washer
- - - - - 6- - - - - 6
- - - - - 6
3X16mm screw3X16mm screw
- - - - - 6- - - - - 6
3mm rubber band
- - - - 6
6mm Playwood
- - - - 6
3mm3mm
Playwood
Cowling
AB
PropellerPropeller
AB
SpinnerSpinner
AB
Install the thr ornamental
3mm Bind nut3mm Bind nut
- - - - - 6- - - - - 6
3X16mm screw3X16mm screw
- - - - - 6- - - - - 6
6mm Playwood
- - - - 6
3mm Washer
- - - - - 8
3X30mm screw
- - - - - 2
3mm rubber band
- - - - 8
2.3X10mm Tp screw
- - - - - 8

33
32 34
Side view
ELEVATOR
Adjust the travel of each control surface to the
values in the diagrams.
These values fit general flight capabilities.
Readjust according to your needs and flight level.
Top view
31
AILERON
Adjustment.
Top view
Adjust the travel of each control surface to the
values in the diagrams.
These values fit general flight capabilities.
Readjust according to your needs and flight level.
1010
Adjustment.
Never fly before checking the Cg s required position.
In order to obtain the CG specified ,reposition the
receiver and battery.
NEVER fly the model
without well balancing.
Warning!
!
CG
Side view
Rudder
Adjust the travel of each control surface to the
values in the diagrams.
These values fit general flight capabilities.
Readjust according to your needs and flight level.
Top view
115-125mm115-125mm
Adjustment
Side view
Adjustment.
45
45
45
45
45
Flap
45
45