CYmodel Bucker Bu.133 Jungmeister User manual

SAFETY PRECAUTIONS
This radio control model is not a toy!
First-time builders should seek advice from people having building
experience in order to assemble the model correctly and to produce
its performance to full extent.
,
Assemble this kit only in places out of children s reach!
Take enough safety precautions prior to operating this model.
,
You are responsible for this model s assembly and safe operation!
Always keep this instruction manual ready at hand for quick
reference,even after completing the assembly.
Could cause serious injury or even death
SPECIFICATION
Warning!
！
Bucker Bu.133 Jungmeister
Specification
Wing Span ..... 2540mm ( 100 in )
Wing Area ..... 192 dm2 ( 2976 sq.in)
Total length.... 2353mm ( 92.6in)
Engine.............100-120cc gas engine
take-off weight....17.2 kg
Radio...............9 channels. 8 servos
Before commencing assembly,please read these instructions thoroughly.
Instruction Manual

REQUIRED FOR OPERATION (Purchase separately)
TOOLS REQUIRED ( Purchase separately)
BEFORE YOU BEGIN
Sharp Hobby Knife Phillips Screw Driver Awl
Needle Nose Pliers Wire Cutters Scissors
Read through the manual before you begin ,so you will have an overall idea of what to do.
Check all parts .if you find any defective or missing parts .contact your local dealer.
Symbols used throughout this instruction manual,comprise.
1
2
3
.
.
.
1
A minimum 4channel radio for airplanes (with 9servos).
And dry batteries.
CAUTION:Onlyuseaminimum4channelradiofor
airplanes!(Nootherradiomaybeused!)

!
12 AA-size Batteries
A minimum 4 channel
transmitter for airplanes.
2
For handing the radio properly.refer to its instruction manual.
3
Purchase a propeller that
will match your engine
4
Silicone Tube Fuel Filter
5
Required for engine starting Glow engine fuel only.
WARNING: Normal gasoline cannot
be used with glow engines.
!
Fuel Pump Plug Wrench
3
Glue
6
Instant glue
Epoxy Glue
3
Other equipment for enhancing
airplane operation & perormance
7
12V Battery (for starter)
Engine Starter
Propeller splinner
2
Warning!
!
Cut off shaded portion.
Ensure smooth non-binding
movement while assembling.
Must be purchased
separately!
Pay close attention
here!
Drill holes with the specified
Diameter(here:2mm)
Assemble left and right
Sides the same way.
Apply instant glue
(CA glue,super glue).
Apply epoxy glue.
Cut off excess.
Do not overlook this symbol.
502
C.A
L
R
A B
2mm
Engine and Muffler
Model Airplane engine:100-120 cc gas engine
Muffler

Accessoriespackinglist
3

!
3
2
1
5
4
4
Epoxy the elevator to the stabilizer
Epoxy the horns to the ailerons and flaps, secure the
servos. install the nylon control horn and connect the linkage
Install the wing
Install the wing servo
Accessory list for this page.
L
R
Below wing
L
R
Upper wing
L
R
Hinge
- - - - - - 16
make sure hinges are
mounted in the same line
make sure hinges are
mounted in the same line
Hinge
- - - - - - 10
BA
BA
Cut off
shaded portion.
upper wing
below wing
Cut off
shaded portion.
Drill holes with the specified
Diameter(here:1.5mm)
2mm
1.5mm
Drill holes with the specified
Diameter(here:3mm)
2mm
3mm
Rod adjuster
- - - - 4
- - - - - - 4
Ball bearing
3X16mm Screw
- - - - - 4
3mm Lock nut
- - - - - - 4
Rod adjuster
Connecting rod head
3X30mm Screw
- - - - 4
- - - - 4
Horn
2.5X140mm Rod
- - - - 4
- - - - 4
- - - 4
- - - 8
2X10mm Screw
- - - 4
3X25mm Screw
- - - 4
4X35mm Screw
- - - 4
Apply instand type AB glue to the
holes in the ailerons flaps and hinges
Hinge
Rod adjuster
- - - - 4
- - - - - - 4
Ball bearing
3X16mm Screw
- - - - - 4
3mm Lock nut
- - - - - - 4
Rod adjuster
Connecting rod head
3X30mm Screw
- - - - 4
- - - - 4
Horn
2.5X140mm Rod
- - - - 4
- - - - 4
- - - 4
- - - 8
2X10mm Screw
- - - 4
3X25mm Screw
- - - 4
4X35mm Screw
- - - 4
- - - 26

!
8
710
9
5
6
Accessory list for this page.
Horizontal/Vertical tail
Install the rudder
Install the stabilizer to the fuselage
28mm
Apply epoxy glue.
A B
3mm fiberglass board
- - - - - 4
------”L”frame-------8
--M3x16mmscrew---16
-----------------------------8
M3x16mmscrew
3mm Washer
- - - - - - - - 4
- - - - - - - 4
Apply epoxy glue.
A B
Securely glue together
,if coming off during flights.
You lose control of your airplane
which leads to accidents!
A
B
A
B
BB
AA
3mm fiberglass board
- - - - - - - - - - 4
------”L”frame-------8
--M3x16mmscrew---16
-----------------------------8
Install the wing
Install the wing
make sure hinges are
mounted in the same line
Hinge - - 4
Apply epoxy glue.
A B

!
13
12 15
14
11
6
Accessory list for this page.
Epoxy the rudder to the vertical
Assemble the lower middle wing
to the fuselage
Install the undercarriage
Apply epoxy glue.
A B
make sure hinges are
mounted in the same line
Center line
Marking
Drill holes with the specified
Diameter(here:5.5mm)
2mm
5.5mm
5x60mm screw
- - - - - 2
5x45mm screw
- - - - - 2
5mm Washer
- - - - - 4
Cut off
shaded portion.
screw 5x45mm
screw 5x60mm
Assemble the lower middle wing
to the fuselage
Assemble the lower middle wing
to the fuselage
5.2mm Collar
- - - - - 4
3X3mm screw
- - - - - - 4
5x60mm screw
- - - - - 2
5x45mm screw
- - - - - 2
5mm Washer
------ - - - - 2
5.2mm Collar
- - - - - 4
3X3mm screw
- - - - - - 4

!
18
17 20
19
16
7
Accessory list for this page.
Install the horns to the rudder
Drill holes with the specified
Diameter(here:2mm)
2mm 2mm
3X25mm Tp screw
Pressure plate
- - - - - -12 - - - - - - 6
Drill holes with the specified
Diameter(here:3mm)
2mm 3mm
25mm
3mm Lock nut
- - - - 3
Connecting rod h ead
3X35mm Screw
- - - - 2
- - - - 2
Horn
- - - - 2
- - 3
elevator
servo
second choice
elevator
servo
the first choice
- - - - 1
- - - - 2
3.2mm Collar
3.2mm Nylon Collar
3X3mm Screw
- - - - 4
- - - - 3
M6 Nut
M6X9 screw
- - - - 1
- - - - 1
3.2mm Collar
- - - - 1
M3X20 Tp screw
45mm Wheel
- - - - 1
1.8X140mm rod
Linkage Stopper
- - - - 1
- - - - 1
Drill holes with the specified
Diameter(here:3mm)
2mm 3mm
Connec ting rod head
3X35mm Screw
- - - - 2
- - - - 2
Horn
- - - - 2
- - 6
4X35mm Screw
- - 2
4X35mm Screw
- - 2
3X25mm Tp screw
Pressure plate
- - - - - -12
- - - - - - 6
3mm Lock nut
- - - - 3
Connecting rod head
3X35mm Screw
- - - - 4
- - - - 4
Horn
- - - - 4
- - 9
4X35mm Screw
- - 4
- - - - 1
- - - - 2
3.2mm Collar
3.2mm Nylon Collar
3X3mm Screw
- - - - 4
- - - - 3
M6 Nut
M6X9 screw
- - - - 1
- - - - 1
3.2mm Collar
- - - - 1
M3X20 Tp screw
45mm Wheel
- - - - 1
1.8X140mm rod
Linkage Stopper
- - - - 1
- - - - 1
Install the undercarriage
Install the tail wheel
Install the elevator servo
Two position options
Install the horns to the elevator

!
23
22 25
8
21 21
Accessory list for this page.
Install the lower wing to the fuselage
Install wing bracing and wire drawing
Install the engine
Drill holes with the specified
Diameter(here:3mm)
2mm 3mm
3X35mm Screw
----2
Drill holes with the specified
Diameter(here:3mm)
2mm 3mm
3X35mm Screw
----2
--steelwire8.5m-------1
---Aluminiumtubes--20
-------Copperjoiner------8
-------Retainer(M3)------8
--M3x16mmscrew---14
---------------------------16
long
short
----Locknut-----8
3X16mm Screw
------- 16
3x16mmTpscrew
-----------7
Assemble the upper middle wing
to the fuselage
Install the upper wing to the fuselage
------------Locknut---------8
3X16mm Screw
--------------- 16
3X35mm Screw
--steelwire8.5m-------1
---Aluminiumtubes--20
-------Copperjoiner------8
-------Retainer(M3)------8
--M3x16mmscrew---14
---------------------------16
3x16mmTpscrew
----------- 7
----------- 4

!
28
27 30
29
9
26
Accessory list for this page.
Install the cowling
Install the engine
After confirming the
position(see front of
fuel tank).
Insert and tighten
the screw.
3X20mm Screw
- - - - 1
Assembly of the full tank
Rod adjuster
- - - 2
Rod
- - - - 2
Aluminium tube
- - - - - 2
Rudder
servo
Assembly of the full tank
3X12mm screw
- - - - - 7
3mm Washer
- - - - - 7
Apply epoxy glue.
A B
Install trapdoor
Rod adjuster
- - - 2
Rod
- - - - 2
Aluminium tube
- - - - - 2
3X12mm screw
- - - - - 7
3mm Washer
- - - - - 7

33
32 34
Side view
ELEVATOR
Adjust the travel of each control surface to the
values in the diagrams.
These values fit general flight capabilities.
Readjust according to your needs and flight level.
Top view
31
AILERON
Adjustment.
Top view
Adjust the travel of each control surface to the
values in the diagrams.
These values fit general flight capabilities.
Readjust according to your needs and flight level.
10
Adjustment.
Never fly before checking the Cg’s required position.
In order to obtain the CG specified ,reposition the
receiver and battery.
NEVER fly the model
without well balancing.
Warning!
!
警告
CG
Side view
Rudder
Adjust the travel of each control surface to the
values in the diagrams.
These values fit general flight capabilities.
Readjust according to your needs and flight level.
Top view
Adjustment
Side view
Adjustment.
CG
45
45
45
45
45
45
150-160mm