CYmodel Spitfire mk IX CY8144 User manual

Before commencingassembly,please readthese instructionsthoroughly.
SAFETY PRECAUTIONS
This radio control model is not a toy!
lFirst-time buildersshould seekadvice frompeople havingbuilding
experience inorder toassemble themodel correctlyand toproduce
its performanceto fullextent. ,
lAssemble thiskit onlyin placesout ofchildrens reach!
lTakeenough safetyprecautions priorto operatingthis model.
,
You areresponsible forthis models assemblyand safeoperation!
lAlways keepthis instructionmanual readyat handfor quick
reference,even aftercompleting theassembly.
lCould causeserious injuryor evendeath
SPECIFICATION
Wing Span: 2800mm (110 in)
2
Wing Area: 142.5dm (2210sq.in)
Total Length: 2370 mm (93 in)
Engine :85-100cc gas engine
Radio : 6 channels ,9 servos
Spitfire MK IX
ALMOST - READY - TO - FLYALMOST - READY - TO - FLY

REQUIRED FOR OPERATION (Purchase separately)REQUIRED FOR OPERATION (Purchase separately)REQUIRED FOR OPERATION (Purchase separately)REQUIRED FOR OPERATION (Purchase separately)
TOOLS REQUIRED ( Purchase separately)TOOLS REQUIRED ( Purchase separately)TOOLS REQUIRED ( Purchase separately)TOOLS REQUIRED ( Purchase separately)
BEFOREYOUBEGINBEFOREYOUBEGINBEFOREYOUBEGINBEFOREYOUBEGIN
SharpHobbyKnife Phillips Screw Driver Awl
NeedleNosePliers Wire Cutters Scissors
Read through the manual before you begin ,so you will have an overall idea of what to do.
Check all parts .if you find any defective or missing parts .contact your local deater.
Symbols used throughout this instruction manual,comprise.
111
222
333
.
.
Warning!
!
Do not overlook this symbol.
Aminimum 6channel radio for airplanes (with 9servos).
And dry batteries.
CAUTION: Only use a minimum 6channel radio for
airplanes! (No other radio may be used!)
!
12 AA-size Batteries
Aminimum 6 channel
transmitter for airplanes.
For handing the radio properly.refer to its instruction manual.
Engine and Muffler
Purchase a propeller that
will match your engine
Silicone Tube Fuel Filter
required for engine starting Glow engine fuel only.
WARNING: Normal gasoline cannot
be used with glow engines.
!
Fuel Pump Plug Wrench
Glue
Instant glue
Epoxy Glue
Other equipment for enhancing
airplane operation & perormance
12VBattery (for starter)
Engine Starter
BBBB
22
Cut off shaded portion.
Ensure smooth non-binding
movement while assembling.
Must be purchased
separately!
Pay close attention
here!
Drill holes with the specified
Diameter(here:2mm)
Assemble left and right
Sides the same way.
Apply instant glue
(CA glue,super glue).
Apply epoxy glue.
Cut off excess.
502
C.AC.A
LL
RR
AB2mm2mm
99
44
11
77
66
55
88
Model Airplaneengine:85-100ccgasengine
receiver
22
Battery (need 2)
33
Servo(need 9 servos )
remote control
Switch (need 2)
AA
Muffler
Muffler
Muffler
Muffler
Ignition
Ignition

!
3
2
1
5
4
33
Install the aileron and flap
Install the servo of aileron
Install the servo
Aileron
Flap
Hinge
Hinge
Install the aileron and flap
Bottom view
Install the servo of flap
Hinge
Hinge
Accessory list for this page.
LL
RR
LL
RR
Securely glue together. If comingoff duringflights,you'll
lose control ofyour airplane whichleads to accidents!
Warning!Warning!
Rod adjuster
Connecting rod head
3X35mm screw
2X8mm screw - - - - - 4
- - - - - 4
- - - - - 6
- - - - - 4
2.5X85mm rod
- - - - - 2
HORN
- - - - - 2
- - - - - 2
4X30 Screw
- - - - - 2
LL
RR
FlapAileron
AB
AB
- - - - - - - - 8
- - - - - - - - 8
A B
A B
Make sure hingesare
mounted in thesame line
2.3X10mm Tp screw
- - - - - 8
LL
RR
Rod adjuster
Connecting rod head
3X12mm TPscrew
2X8mm screw
- - - - - 4
- - - - - 4
- - - - - 6
- - - - - 4
2.5X85mm rod
- - - - - 2
HORN
- - - - - 2
4X30 Screw
- - - - - 2
2.3X10mm Tp screw
- - - - - 8
Flap Aileron
Tailing edge
Aileron
4mm
Servo line
Rod adjuster
Connecting rod head
3X35mm screw
2X8mm screw
- - - - - 8
- - - - - 8
- - - - - 6
- - - - - 8
2.5X85mm rod
- - - - - 4
HORN
- - - - - 4
- - - - - 2
4X40 Screw
- - - - - 4
2.3X10mm Tp screw
- - - - - 16
- - - - - - - - 8
- - - - - 8
LL
RR
Servo line
3X12mm TPscrew
- - - - - 6
3mm3mm
Flap.
Aileron

!
8
7
6
10
9
44
Accessory list for this page.
Air tank
Switch
Air inlet
3-way
pressure inlet
3-way
pressure inlet
3-way
pressure inlet
Quick release connector
Quick release connector
Pressure reduction inlet
Strut
Strut
Pleas notice the inner diameter for each
side of the pressure reduction inlet.
Please insure the sealing of the retract
system before flight . Retainer
Rod adjuster
2X8mm screw
- - - - - 1
- - - - - 1
- - - - - 1
Rod (1.8X80mm)
- - - - - 1
900 Air line
- - - - - 2
Install the main landing gear
Install the main landing gear Main wing installing(Bottom)
LL
RR
3X3mm screw
5.2mm Collar
3X20mm Tp screw
- - - - - 8
5X45mm Axletree
- - - - - 2
- - - - - 2
- - - - - 2
4X4mm screw
- - - - - 2
Install the main landing gear
4mm4mm
4X55mm screw 4mm Washer
- - - - - - - - 4
- - - - 4
32X915mm Tube
20X665mm Tube LL
RR
Play wood
Play wood
- - - - - - - - - - - -2
- - - - - - - - - - - -4
A B
Main wing installing(Top)
Servo line
Servo line
Air line
Air line
3X3mm screw
5.2mm Collar
3X20mm Tp screw
- - - - - 8
5X45mm Axletree
- - - - - 2
- - - - - 2
- - - - - 2
4X4mm screw
- - - - - 2
Retainer
Rod adjuster
2X8mm screw
- - - - - 1
- - - - - 1
- - - - - 1
Rod (1.8X80mm)
- - - - - 1
900 Air line
- - - - - 2 Play wood
Play wood
4X55mm screw
4mm Washer
- - - - - - - - 4
- - - - 4 - - - - - 2
- - - - - - - - 4

!
13
12 15
1414
55
11
Accessory list for this page.
Install the elevator
Install the elevator
Install the elevator servos
Install the rudder
Install the elevator servos
LL
RR
Securely glue together. If comingoff duringflights,you'll
lose control ofyour airplane whichleads to accidents!
Warning!Warning!
LL
RR
Bottom view
LL
RR
make sure hingesare
mounted in thesame line
Hinge
- - - - - - - 4
A B
A B
LL
RR
Rod adjuster
Connecting rod head
3X30mm screw
2X8mm screw
- - - - - 4
- - - - - 2
- - - - - 6
- - - - - 4
2.5X85mm rod
- - - - - 2
HORN
- - - - - 2
- - - - - 2
4X40 Screw
- - - - - 2
make sure hingesare
mounted in thesame line
AB
Hinge
- - - - - - - - 6
LL
RR
LL
RR
3mm3mm
3mm3mm
Servo line
Rod adjuster
Connecting rod head
3X30mm screw
2X8mm screw
- - - - - 4
- - - - - 2
- - - - - 6
- - - - - 4
2.5X85mm rod
- - - - - 2
HORN
- - - - - 2
- - - - - 2
4X40 Screw
- - - - - 2
Hinge
- - - - - 10

!
18
17 20
19
16
66
Accessory list for this page.
Install the rudder
Install the servo of rudder&tail wheel
- - - - 2
- - - - 1
3.2mm Collar
3.2mm Nylon Collar
3X3mm Screw
- - - - 2
- - - - 3
6X9 screw - - - - 1
- - - - 1
M3X20 Tp screw
3.2mm Rocker
- - - - - 1
6mm nut
3mm3mm
Aluminium tube
Rod adjuster
2X8mm screw
- - - - - 2
- - - - - 2
Rod - - - - - 2
- - - - - 2
Securely glue together. If comingoff duringflights,you'll
lose control ofyour airplane whichleads to accidents!
Warning!Warning!
Tailing edge
Rudder
4mm
AB80mm spring
- - - - - 2
Install the servo of rudder&tail wheel
Install the servo of rudder&tail wheel
Install the servo of rudder&tail wheel
Aluminium tube
Rod adjuster
Connecting rod head
2X8mm screw
- - - - - 2
- - - - - 2
- - - - - 2
Rod - - - - - 2
- - - - - 2
3mm nut - - - - - 6
800mm Steel wire
- - - - - 2
HORN
- - - - - 2
4X30 Screw
- - - - - 2
3X45mm screw
- - - - - 3
Aluminium tube
Rod adjuster
Connecting rod head
2X8mm screw
- - - - - 4
- - - - - 4
- - - - - 2
Rod - - - - - 4
- - - - - 4
3mm nut - - - - - 6
800mm Steel wire
- - - - - 2
HORN
- - - - - 2
4X30 Screw
- - - - - 2
3X45mm screw
- - - - - 3 3X35mm screw
- - - - - 1
3X30mm screw
- - - - - 1
- - - - 2
- - - - 1
3.2mm Collar
3.2mm Nylon Collar
3X3mm Screw
- - - - 2
- - - - 3
6X9 screw - - - - 1
- - - - 1
M3X20 Tp screw
3.2mm Rocker
- - - - - 1
6mm nut
3X35mm screw
- - - - - 1
3X30mm screw
- - - - - 1
80mm spring
- - - - - 2

!
23
25
77
21 24
22
Accessory list for this page.
4X20mm screw
4mm Washer
- - - - - - - - 2
- - - - 2
4mm4mm
Fuselage installing
Horizontal
(Put the servo into the fuselage)
5X30mm screw
5mm Washer
- - - - - - - - 4
- - - - 4
502
C.AC.A
5mm Bind nut
5X45mm screw
- - - - - 2
5mm Washer
- - - - - 2 - - - - - 2
8X50mm Carbon tube
- - - - - 2
5mm5mm
Securely glue together
,if coming off during flights.
You lose control of your airplane
which leads to accidents!
AA
B B
C C
AA
B
B
C
C
Main wing&Horizontal/Vertical tail
Warning!
!
8mm8mm
Main wing installing
Installing the engine (85-100cc)
AB
200mm
ThrottleThrottleFuel tankFuel tank
4X20mm screw 4mm Washer
- - - - - - - - 2
- - - - 2
5X30mm screw
- - - - 4
5mm Bindnut
5X45mm screw
- - - - - 2
5mm Washer
- - - - - 2 - - - - - 6
8X50mm Carbon tube
- - - - - 2

3mm3mm
Playwood
Cowling
!
28
27 30
29
88
26
Accessory list for this page.
After confirmingthe
position(see frontof
fuel tank).
Insert and tighten
the screw.
Fuel supply line
Fuel pipe Air pressure line
1.8X450mm Rod
- - - - - - 1
Linkage Stopper
2mm Nut
- - - - 1
- - - - 1
3X3mm Screw
- - - - - - 1
Install the throttle servo
Assembly of the full tank
Radio Equipment
Install the thr cowling
ReceiverReceiver
BatteryBattery
Battery/IgnitionBattery/Ignition
3mm Bind nut
3mm Washer
- - - - - 6
- - - - - 6
3X16mm screw
- - - - - 6
3mm rubber band
- - - - 6
6mm Playwood
- - - - 6
Install the thr cowling
AB
SpinnerSpinner
PropellerPropeller
3mm Bind nut
3mm Washer
- - - - - 6
- - - - - 6
3X16mm screw
- - - - - 6
3mm rubber band
- - - - 6
6mm Playwood
- - - - 6
1.8X450mm Rod
- - - - - - 1
Linkage Stopper
2mm Nut
- - - - 1
- - - - 1
3X3mm Screw
- - - - - - 1

!
33
35
99
31 34
32
Accessory list for this page.
Install the canopy
Install the canopy
Install the canopy
Install the canopy
2.3X10Tp screw
- - - - - 6
A B
Cut away the surplus pats
of canopy,care fully along
the shaded line.
502
C.AC.A AB
LL
RR
502
C.AC.A
502
C.AC.A
LL
RR
AB
502
C.AC.A
Install the canopy
Blcak lineBlcak line
Red lineRed line
1.5V1.5V 1.5V1.5V
BatteryBattery
2.3X10Tp screw
- - - - - 6

38
37 39
Side view
ELEVATOR
Adjust the travel of each control surface to the
values in the diagrams.
These values fit general flight capabilities.
Readjust according to your needs and flight level.
Top view
36
AILERON
Adjustment.
Top view
Adjust the travel of each control surface to the
values in the diagrams.
These values fit general flight capabilities.
Readjust according to your needs and flight level.
1010
Adjustment.
Never fly before checking the Cg s required position.
In order to obtain the CG specified ,reposition the
receiver and battery.
NEVER fly the model
without well balancing.
Warning!
!
CG
Side view
Rudder
Adjust the travel of each control surface to the
values in the diagrams.
These values fit general flight capabilities.
Readjust according to your needs and flight level.
Top view
185-195mm185-195mm
Adjustment
Side view
Adjustment.
45
45
45
45
45
Flap
45
45