CYP CH-1601TXRX User manual

CH-1601TXRX
HDMI/Audio over CAT5e/6/7 Extender with 48V PoH
Operation Manual
Operation Manual

DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. Cypress Technology assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies
that may be contained in this document. Cypress also makes no
commitment to update or to keep current the information contained
in this document.
Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means
- electronic, mechanical, magnetic, optical, chemical, manual,
or otherwise - without express written permission and consent from
Cypress Technology.
© Copyright 2014 by Cypress Technology.
All Rights Reserved.
Version 1.0 November 2014
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.

SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack or install or
operate this equipment, and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through
module openings or empty slots, as you may damage parts.
• Do not attach the power supply cabling to building surfaces.
• Do not allow anything to rest on the power cabling or allow it to
be abused by persons walking on it.
• To protect the equipment from overheating, do not block the slots
and openings in the module housing that provide ventilation.
REVISION HISTORY
VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE
VR0 20/10/15 Preliminary Release
VR1 01/12/15 Add HDBT Spec. Table

CONTENTS
1. Introduction............................................ 1
2. Applications........................................... 1
3. Package Contents ................................ 1
4. System Requirements............................ 1
5. Features.................................................. 2
6. Operation Controls and Functions....... 3
6.1 Transmitter’s Front Panel..................3
6.3 Receiver’s Front Panel.....................5
6.4 Receiver’s Rear Panel .....................6
6.5 IR Cable Pin Assignment..................8
6.6 D-Sub 9-Pin Assignment...................8
7. Connection Diagram ............................ 9
8. Specications ...................................... 10
8.1 Technical Specication.................10
8.2 CAT5e/6/7 Cable Specication ...11
8.3 HDBT Specication.........................11
8.4 Supported Resolutions...................12
9. Acronyms ............................................. 13

1
1. INTRODUCTION
This HDMI and Audio over Single CAT5e/6/7 Transmitter and Receiver
set can send uncompressed audio/video along with controls, IP and
USB data over a single run of CAT5e/6/7 cable up to 100m. It has the
added benet of control through the built-in RS-232 and IR ports and
a bidirectional LAN serving connection. There is a bidirectional digital
audio capability that gives users the convenience of an additional
audio connection. This system also allows the connection of any
USB host, enabling a USB connection to up to 2 USB ports, giving the
Receiver the ability to act like a USB hub. The 48V PoH design can
power the Receiver (PD) from the Transmitter (PSE), eliminating the
need for a separate power supply for the Receiver.
2. APPLICATIONS
• 48V PoH from Transmitter (PSE) to Receiver (PD)
• Household entertainment extending and control
• Lecture room display and control
• Showroom display and control
• Meeting room presentation and control
• Classroom display and control
3. PACKAGE CONTENTS
• 1 x HDMI/Audio over CAT5e/6/7 Transmitter
• 1 x CAT5e/6/7 to HDMI/Audio Receiver
• 1 x IR Blaster
• 1 x IR Extender
• 1 x 48 DC Power adaptor
• 1 x Power Cord
• 1 x Operational Manual
4. SYSTEM REQUIREMENTS
Input source equipment such as DVD/Blu-ray player, host PC/Laptop
and HDMI equipped output display (TV or monitor) with amplier or
active speakers.

2
5. FEATURES
• Supports HDBaseT 2.0 specication supporting over a single CAT6/7
cable up to 100m/328ft and CAT5e cable up to 90m/295ft
• Fully compliant with HDMI 1.4, and compatible with HDMI 2.0 (4K2K
60Hz with 4:2:0)
• Receiver features 2 USB 2.0 ports
• HDMI (with 3D & 4Kx2K support), HDCP and DVI compliant
• HDBaseT 5Play™ convergence: High-Denition (HD) Video and
Audio, 100BaseT Ethernet, PoH and Control (Bidirectional IR/RS-232
pass-through)
• Supports pass-through of audio formats: LPCM2/5.1/7.1CH, Dolby
Digital 2~5.1Ch, Dolby Digital Plus, Dolby TrueHD, Dolby Atmos and
DTS-HD Master Audio
• Supports coaxial cable up to 2 meter with sampling rate up to 48kHz
• Supports Ethernet network connection
• Bidirectional LAN and external digital audio capability
• Supports RS-232 baud rate from 110~115200bps

3
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Transmitter’s Front Panel
RS 232 IN IR IN 2 IR OUT 1LAN CAT5e/6/7 OUT DC 48V
POWER
UPDATE

7654321
1Update Switch
Switch this deep switch to right for rmware update use, under
normal operation, leave the switch on left.
2RS-232 IN
Connect to a PC or Laptop with D-Sub 9- pin female cable for the
transmission of RS-232 commands.
3IR IN 2
Connect to the supplied IR Extender cable for IR signal reception.
Ensure that remote being used is within the direct line-of-sight of
the IR Extender.
4IR OUT 1
Connect to the supplied IR Blaster Cable for IR signal transmission.
Place the IR Blaster in direct line-of-sight of the equipment to be
controlled.
5LAN
Connect to internet or network service system to this slot or to the
LAN port slot of the equipment device for a total sharing rate of
100Mbps within the link. The yellow LED will illuminate to represent
the link with Receiver is steady, when it blink irregularly it represent
the link error or when not illuminate it means no link with Receiver.
The green LED will illuminate to represent the Ethernet speed is with
100Mbit/s.
6CAT5e/6/7 OUT
Connect to the Receiver unit with CAT5e/6/7 cable for transmission
of all data signals. The yellow LED will illuminate to represent the
link between Transmitter and Receiver is steady, when it blink

4
irregularly it represent the link error or when not illuminate it means
no link with Receiver. The green LED will illuminate to represent the
PoE activation.
7DC 48V & POWER LED
Plug the 48V DC power supply into the unit and connect the
adaptor to an AC outlet and the LED will illuminate.
6.2 Transmitter’s Rear Panel
HDMI IN COAX AUDIO IN
OUT 1IN
2R
L
USB
ARC OUT
OFFON
ARC
5 64321
1HDMI IN
Connect to HDMI source equipment such as a DVD or Blu-ray
player.
2USB
Connect from PC or Laptop for data transmit to or control from the
Receiver’s USB slots.
3COAX OUT 1
Connect to speaker with coaxial input for audio signal output from
Receiver’s COAX IN 1.
4COAX IN 2
Connect to audio source equipment such as DVD or Blu-ray player
for audio signal sending to Receiver’s COAX OUT2.
5AUDIO IN L/R
Connect with audio source equipment such as PC or CD player for
audio signal sending to Receiver’s AUDIO OUT L/R.
6ARC OUT ON/OFF
Switch this dip switch to allows ARC (Audio Return Channel)

5
function to be activate or not. Switch to OFF to disable ARC
function.
Switch to ON allows Receiver's HDMI output/COAX IN audio to be
routed back and output to both HDMI IN and COAX OUT 1 on the
Transmitter side.
Note: When ARC switch to ON, depending on the connected
devices of the HDMI OUT & Coaxial in from Receiver and the
connected device of the HDMI In & Coaxial Out at the Transmitter
the audio format and behavior may be varied. The ARC input/
output transmission distance may be varied too, it is suggested to
use cable within 2 meters long to ensure the best audio quality.
6.3 Receiver’s Front Panel
RS 232 OUT IR IN 1 IR OUT 2LAN CAT5e/6/7 IN
POWER
UPDATE

7654321
1Update Switch
Switch this deep switch to right for rmware update use, under
normal operation, leave the switch on left.
2RS-232 OUT
Connect to the device that is to be controlled (via D-Sub 9-pin
male cable) by RS-232 commands.
3IR IN1
Connect to the supplied IR Extender cable for IR signal reception.
Ensure that remote being used is within the direct line-of-sight of
the IR Extender.
4IR OUT 2
Connect to the supplied IR Blaster cable for IR signal transmission.
Place the IR Blaster in direct line-of-sight of the equipment to be
controlled.
5LAN
Connect to internet or network service system to this slot or to

6
the LAN port slot of the equipment device for a total sharing
rate of100Mbps within the link. The yellow LED will illuminate to
represent the link with Transmitter is steady, when it blink irregularly
it represent the link error or when not illuminate it means no link.
The green LED will illuminate to represent the Ethernet speed is with
100Mbit/s.
6CAT5e/6/7 IN
Connect to the Transmitter unit with CAT5e/6/7 cable for
transmission of all data signals. The yellow LED will illuminate to
represent the link between Transmitter and Receiver is steady,
when it blink irregularly it represent the link error or when not
illuminate it means no link with Receiver. The green LED will
illuminate to represent the PoH activation.
7POWER LED
This LED will illuminate when the device is connected with power
supply.
6.4 Receiver’s Rear Panel
HDMI OUT COAX AUDIO OUT
OUT 2IN
1R
L
POWER
LINK 1
LINK 2
USB
COAX
IN
ARC
IN
ARC
876542 3 91
1HDMI OUT
Connect to a HDMI equipped TV/monitor for display of the HDMI
input source signal.
2USB
Connect to USB peripheral devices such as printer, keyboard, ash
driver or …etc. for data receiving or sending back to Transmitter.
3POWER LED
This LED will illuminate when device is connected with USB power
supply.

7
4LINK 2
This LED will illuminated when the lower USB slot is connected with
signal activated.
5LINK 1
This LED will illuminated when the upper USB slot is connected with
signal activated.
6COAX OUT 2
Connect to speaker with coaxial input for audio signal output from
Transmitter’s COAX IN 2.
7COAX IN 1
Connect to audio source equipment such as DVD or Blu-ray player
for audio signal sending to Transmitter’s COAX OUT1
8AUDIO L/R OUT
Connect to speaker with RCA input for audio signal output.
9ARC IN/COAX IN
Switch this switch to select ARC channel. Switch to ARC IN to use
HDMI OUT's audio or switch to COAX IN to use COAX IN 1's audio.
The audio will be routed back and output to both HDMI IN and
Coaxial OUT on the Transmitter side.
Note: When ARC switch to ON, depending on the connected
devices of the HDMI OUT & Coaxial in from Receiver and the
connected device of the HDMI In & Coaxial Out at the Transmitter
the audio format and behavior may be varied. The ARC input/
output transmission distance may be varied too, it is suggested to
use cable within 2 meters long to ensure the best audio quality.

8
6.5 IR Cable Pin Assignment
3
1
3
1
2
2
Power
IR Blaster Signal
NC
IR Signal
Power
Grounding
IR Receiver
IR Blaster
6.6 D-Sub 9-Pin Assignment
pin Dene TX / RX
1 N/C
2 TxD / RxD
3 RxD / TxD
4 N/C
5 GND
6 N/C
7 N/C
8 N/C
9 N/C

9
7. CONNECTION DIAGRAM
HDMI IN COAX AUDIO IN
OUT 1IN 2RL
USB
ARC OUT
OFFON
ARC
HDMI OUT COAX AUDIO OUT
OUT 2IN 1RL
POWER
LINK 1
LINK 2
USB
COAX
IN
ARC
IN
ARC
RS 232 IN IR IN 2IR OUT 1LAN CAT5e/6/7 OUT DC 48V
POWER
UPDATE

RS 232 OUTIR IN 1IR OUT 2LAN CAT5e/6/7 IN
POWER
UPDATE

1.5m
60°
1.5m
60°
7m
3m 3m
60°
m
7m
3m 3m
60°
m
DVD or Blu-ray Player
Active Speakers
HD TV
Active Speakers
DVD or Blu-ray Player
DVD or Blu-ray Player
HDMI
TX
TXRX
RX
Note Book
PC or Note Book
RS-232
RS-232
RS232 Equipped
PC or Note Book
Internet ModemHub
or Router
CAT5e/6/7
IR Blaster
IR Extender
RS232 Equipped
HDMI Switcher
HDMI
USB Keyboard USB Mouse

10
8. SPECIFICATIONS
8.1 Technical Specication
Video Bandwidth 340MHz/10.2Gbps
Transmitter
Input Ports 1 x HDMI
1 x LAN, 1 x RS-232,
1 x IR, 1 x USB,
1 x Coaxial, 1 x L/R
Output ports 1 x CAT5e/6/7, 1 x IR
1 x Coaxial
Receiver
Input Ports 1 x CAT5e/6/7, 1 x IR,
1 x Coaxial
Output Ports 1 x HDMI, 1 x RS-232, 1 x LAN,
1 x Coaxial, 1 x IR, 2 x USB, 1 x L/R
HDMI Cable Length I:10M/1080p@12 bits, 5M/4K2K
O:15M/1080p@12 bits, 5M/4K2K
IR Frequency 30~50kHz
Baud Rate Up to 115200bps
Power Supply 48VDC/0.83A (US/EU standards, CE/FCC/
UL certied)
ESD Protection Human body model:
±8kV (air-gap discharge)
±4kV (contact discharge)
Dimensions 160mm (W) x 130mm (D) x 30mm (H)/
Jacks Excluded
165mm (W) x 141mm (D) x 33mm (H)/
Jacks Included
Weight 624g/Tx, 618g/Rx
Chassis Material Metal
Silkscreen Color Black
Operating Temperature 0˚C~40˚C / 32˚F ~ 104˚F
Storage temperature -20˚C~60˚C / -4˚F ~ 140˚F
Relative Humidity 20~90% RH (no condensation)
Power Consumption 19w

11
8.2 CAT5e/6/7 Cable Specication
Cable
Type Range Pixel clock rate
Video Data
Rate
Supported
Video
CAT5e/6/7 100 m <=225 MHz <=5.3 Gbps
(HD Video)
Up to 1080p,
60 Hz, 36 bits,
3D (data rates
lower than 5.3
Gbps or below
225 MHz TMDS
clock).
90 m/CAT5e
100 m/
CAT6/7
>225 MHz > 5.3 Gbps
(Ultra HD
Video)
4K2K, 30Hz
video formats
8.3 HDBT Specication
HDBT FEATURE SUPPORT
ARC Yes
Video & Audio Yes
LAN Yes
IR Yes
RS-232 Yes
Send Power to TX No
Send Power to RX Yes
USB Yes

12
8.4 Supported Resolutions
Resolution Input Output
640×480@60 √ √
720×480@60 √ √
720×576p@50 √ √
800×600@60 √ √
1024×768@60 √ √
1280×720@50 √ √
1280×720p@50 √ √
1280×720p@60 √ √
1280×1024@60 √ √
1360x 768@60 V V
1600×1200@60 √ √
1920×1080i@50 √ √
1920×1080i@60 √ √
1920×1080p@24 √ √
1920×1080p@25 √ √
1920×1080p@30 √ √
1920×1080p@50 √ √
1920×1080p@60 √ √
1920×1200@60 (RB) √ √
3840×2160@24 √ √
3840×2160@25 √ √
3840×2160@30 √ √
3840×2160@60 √ √
3840×2160@60 (YUV420) √ √
4096×2160@24 √ √

9. ACRONYMS
ACRONYM COMPLETE TERM
DTS Digital Theater System
DVI Digital Visual Interface
EDID Extended Display Identication Data
HDCP High-bandwidth Digital Content Protection
HDMI High-Denition Multimedia Interface
HDTV High-Denition Television
LCM Liquid Crystal Monitor
USB Universal Serial Bus
VGA Video Graphics Array
WUXGA Wide Ultra Extended Graphics Array

Home page: http://www.cypress.com.tw
CYPRESS TECHNOLOGY CO., LTD
MPM-CH1601TXRX