CYP EL-C61C User manual

OPERATION MANUAL
EL-C61C
v1.3 HDMI 6-Way Switcher
with CEC

Table of Contents
1. Introduction 1
2. Features 1
3. Package Contents 2
4. Operation Controls and Functions 2
4.1 Front Panel Diagram 2
4.2 Rear Panel Diagram 3
4.3 Remote Control 4
5. RS232 Pinouts 5
6. Commands Sets 5-6
7. Connection Diagram 7
8. Specications 8

Page 1
1. Introduction
The EL-C61C switcher allows the user to input six HDMI sources and switch
between these sources to provide a single HDMI output to a display. This switcher
can be controlled via the supplied remote control or by using the input switching
button on the front of the device. The EL-C61C also features a CEC command
function allowing the device to Auto-Switch on source power up.
2. Features
• v1.3 HDMI, HDCP 1.1 and DVI 1.0 compliant
• HDMI 6-Way Switcher with Consumer Electronics Control (CEC)
• Resolutions Supported: PC - VGA, SVGA, XGA, SXGA, UXGA. HDTV - 480i, 576i,
480p, 576p, 720p, 1080i, 1080p and 1080p24fps
• High Denition Audio supported - Dolby TrueHD, Dolby Digital Plus and DTS-HD
Master Audio plus LPCM
• Auto signal enhancement feature can improve signal quality after long distance
transmission
• RS-232 & IR Remote Control
• CEC Auto switch control function
• Supports ‘Deep Colour’ (10 & 12 bit)
• Supports xvYCC
• Supports 3D signals

Page 2
4. Operation Controls and Functions
4.1 Front Panel
3. Package Contents
• 6 by 1 HDMI v1.3 Switcher
• Remote Control (CR-63 with battery)
• 5V DC Power Supply Adaptor
• Operation Manual.
1. Remote control sensor.
2. HDMI IN 1~2: These slots connect to the HDMI/DVI output ports of your source
equipments. ie, set- up-box, DVD or Blue Ray.
3. Input select indicators: Press the “INPUT” button repeatedly to switch to your
desired input source. The LED that illuminates indicate the corresponding input
source is selected.
4. CEC button and Indicator. Press button to switch between CEC On and Bypass
mode. When the LED is on, CEC is ON. CEC commands from the source will affect
the unit and the connected display. When this is off, the unit is in Bypass mode.
CEC is passed through the switch to the display, the unit does not respond itself.
Note: Both input source and output display must support CEC for the switcher to
properly perform CEC.
5. POWER indicator: When power is connected to the device, the device
automatically turns on and the power LED will turn red. Note: To turn ON or switch
the device to standby mode, please press the “POWER” button on the remote
control unit.
2 1 3
6
2
5
1 INPUT POWER
4
HDMI IN CEC
ON/Bypass
xvYCC
Deep Color
CEC
HD Audio
Switcherv1.3EL-C61C 6x1 HDMI
2344
1

Page 3
4.2 Rear Panel
1. HDMI OUT: This is the slot where you connect the HDMI output of the switcher to
the HDMI input of your display using a HDMI cable.
2. RS-232 input: When doing rmware upgrade and/or PC remote system control,
connect a D-sub 9 pin cable from this RS232 slot to your computer.
3. HDMI IN 3~6: These slots connect to the HDMI/DVI output ports of your source
equipments. ie, set- up-box, DVD or Blue Ray.
4. DC 5V: Connect the 5V DC power adaptor into this slot and plug the adaptor to an
AC wall outlet.
HDMI OUT 6 5 4 3
DC 5V
RS-232
HDMI IN
2 3 4
1

Page 4
4.3 Remote Control
CR-63
POWERCEC
INPUT
3 4
1 2
5 6
7 8
①
③
②
1. Power: Press the button to turn on the unit-or set the device to standby mode.
2. CEC: Press the button to turn on /Bypass the CEC function. When the LED
illuminate it means CEC is ON and both input source and output display must
support CEC function in order to perform CEC rightly. Press again to switch CEC
to Bypass mode and the LED will not illuminate.
3. Input Selector: Press from 1-6 to select desired input source. No. 7-8 is not
functioning on this model.

Page 5
5. RS232 Pinouts
EL-C61C Remote Control Console
PIN Denition PIN Denition
1 NC 1 NC
2 Tx 2 Rx
3 Rx 3 Tx
4 NC 4 NC
5 GND 5 GND
6 NC 6 NC
7 NC 7 NC
8 NC 8 NC
9 NC 9 NC
RS-232 transmission format:
• Baud Rate: 19200 bps
• Data bit: 8 Bits
• Parity: None
• Stop Bit: 1 bit
• Flow Control: None
COMMAND CODE
Comment
PORT 1 PORT 1 ON
PORT 2 PORT 2 ON
PORT 3 PORT 3 ON
PORT 4 PORT 4 ON
PORT 5 PORT 5 ON
PORT 6 PORT 6 ON
POWER 1 POWER ON
POWER 0 POWER OFF
6. Command Sets

Page 6
Note:
1. The command is a combination of characters and digits.
2. This combination command code has to be separated by ASCII character
SPACE.
3. If the command is legal the unit will reply “OK” message .
4. If the command is illegal, the unit will prompt you with a “NG” message.
5. If you have any problems with the codes, please use the historical codes
below.
COMMAND CODE
Comment
I1 PORT 1 ON
I2 PORT 2 ON
I3 PORT 3 ON
I4 PORT 4 ON
I5 PORT 5 ON
I6 PORT 6 ON
P1 POWER ON
P0 POWER OFF
C1 CEC ON
C0 CEC OFF
SREPORT STATE
Historical Codes
CEC 1 CEC ON
CEC 0 CEC OFF
ST REPORT STATE

Page 7
7. Connection Diagram

Page 8
8. Specications
HDMI Input Port 6 x HDMI female ports + 1 x RS-232
HDCP Version V1.1
HDMI Output Port 1 x HDMI female port
Color Space YCbCr 4:2:2 16/20/24 bits
Deep Colour RGB / YCbCr 4:4:4 24/30/36 bits
ESD Protection Human body model: ± 10kV (air-gap discharge)
± 6kV (contact discharge)
Input TMDS signal 1.2 Volts (peak-to-peak)
Input DDC signal 5 Volts (peak-to-peak, TTL)
Frequency bandwidth 2.25Gbps (single link)
Power Supply 5V/1A DC (US/EU standards, CE/FCC/UL certied)
Dimensions (mm) 240 (W) x 110 (D) x 50 (H)
Weight (g) 540
Chassis Material Aliminium
Chassis Colour Black
Operating Temperature Operating from 0°C ~ 48°C

Notes:

www.cypeurope.com