CYP PU-22HC User manual

OPERATION MANUAL
PU-22HC
v1.3 HDMI/CAT6 to HDMI/
CAT6 Cascader

Table of Contents
1. Introduction 1
2. Features 1
3. Package Contents 2
4. Operation Controls and Functions 2
4.1 Front Panel Diagram 2-4
4.2 Rear Panel Diagram 4
5. Pin Denitions 5
6. Connection Diagram 5
7. Specications 6

Page 1
1. Introduction
All the PUMA, HDMI over CAT5e/6 transmitters and receivers are the perfect
solution to extend HDMI signals via CAT cabling up to 40m. The PU-22HC cascader
with its dual input and outputs allows for great exiblity within any HDMI over CAT6
system.
2. Features
• v1.3 HDMI, HDCP 1.1 and DVI 1.1 compliant.
• HDMI/CAT6 to HDMI/CAT6 Cascader.
• Resolutions supported: PC - VGA to WUXGA; HDTV - 480i to 1080p plus
1080p24fps..
• High Denition Audio supported: Dolby TrueHD, Dolby Digital Plus and DTS-HD
Master Audio plus LPCM.
• Supports CEC functions.
• CAT I/O can run up to 40m @ 1080p8bit video. HDMI Output can run up to
15m.
• CAT I/O can run up to 40m @ 1080p8bit video and can be extended with the
PU-108 CAT repeater.
• Supports ‘Deep Colour’ (10 & 12 bit).
• Equalises and recovers incoming TMDS data before re-transmitting to ensure
optimum signal quality.
• CAT output is ideal for cascading to other HDMI products within the PUMA
range.
• System reset function switch generate a command every 10 minutes to the
connected display which resets them to the correct HDMI input.

Page 2
4. Operation Controls and Functions
4.1 Front Panel
1. HDMI/CAT6 input selection: Switch to select input sources either from HDMI or
CAT6.
2. EDID Control Switcher: Default factory setting is TV, leave as if the display is
properly. Switch to STD to use built-in EDID.
Note:
1. When EDID switch to TV, the unit will detect the  rst HDMI’s output EDID and
record in the unit. If the  rst detected HDMI output is DVI it will pass to next
output until the rst HDMI output detected. The detection priority is HDMI v1.3
> HDMI v1.2 > DVI.
3. Package Contents
• 1 x HDMI/CAT6 to HDMI/CAT6 Splitter Switcher
• 5V DC power supply adaptor
• Operation Manual
EDID
CAT6HDMI
IN
HDMI IN
TVSTD
CEC OUT
HDMI
CAT6
HDMI
ONLY
DDC
CAT6 IN
VIDEO DC 5V
12 3 4 5 6

Page 3
2. When EDID switch to STD the unit will use built-in EDID which supports: Video
1080p 8-bit (max), Audio PCM 2CH
3. When EDID is switch to STD with input selection on HDMI or CAT6 IN the
display TV or monitor will switch to HDMI input 1, automatically. When EDID
is switch to TV regardsless of the input selection the display TV or monitor will
switch to HDMI input 1 mode. Therefore, it is not suggested to switch the EDID
to STD.
4. The EDID selection will only activate when the unit is re-plug and power on.
Power: This slot is where you plug the 5V DC power supply into the unit and
connect the adaptor to an AC wall outlet.
3. CEC output: When switch to HDMI ONLY, the HDMI output port’s CEC will bypass
the CEC commend directly to the HDMI and CAT6 input ports. When switch to
HDMI and CAT6, the HDMI and CAT6 output port’s CEC will bypass the CEC
commend cross to the HDMI .
4. HDMI Input: Connect input port to the HDMI or DVI output port of your source
equipment such as DVD player or set-top-box.
5. CAT6 IN: These slots are for connecting the Video/DDC input to the Video/DDC
output of the transmitter unit with CAT6 cables.
Note:
1. Cable tested with CAT-6E / 23AWG / Solid and therefore, cable with different
speci cation may result in different distance.
2. Cable distance tested with equipment PS3 40G and 37” SamSung 12 bits LCD

Page 4
4.2 Rear
1. CAT6 OUT: Connect the Video/DDC output to the Video/DDC input of the
receiver unit using CAT6 cables.
2. HDMI OUT: Connect HDMI output port to the HDMI display.
3. HDCP indicators: When the input source is with the HDCP protection the HDCP
LED will illuminate.
4. SYNC Indicator: The LED will illuminate when the HDMI or DVI source had been
connected.
5. HDMI/CAT6 input indicator: The LED will illuminate when the HDMI or CAT6
source is selected.
6. Link OUT: The LED will illuminate when the display had been connected.
12 1 6
35
HDCP
CAT6 HDMI
SYNC
VIDEO
CAT6 OUT
DDC
HDMI OUT
LINK OUT
IN
2. Figures provided in this manual are reference  gures only, actual  gures may
depend on source and display use with cable speci cation.
6. DC 5V: This is the slot where you insert the 5V DC power supply for electrical
power before plugging the adaptor to an AC wall outlet.

Page 5
Pin Video DDC
1 TX2+ DDC Bus Clock
2 TX2- NC
3 TX1+ DDC Bus Data
4 TX0+ Power 5V
5 TX0- GND
6 TX1- IR IN
7 TXC+ HPD
8 TXC- CEC
5. Pin
6. Connection Diagram

Page 6
7. Specications
Input Port Transmitter: 1x HDMI female port, 1x IR jack,
Receiver: 2 x CAT5e/6, 1 x IR Jack
Output Port Transmitter: 2 x CAT5e/6, 1 x IR Jack
Receiver: 1x HDMI female port, 1x IR jack
EDID STD / TV
HDMI Audio Output PCM2, 5.1, 7.1, Dolby 5.1, DTS 5.1, DD+,
D-TrueHD, DTS-HD
HDMI Cable In 1080p 8-bit (15M), 12-bit (15M)
HDMI Cable Out 1080p 8-bit (15M), 12-bit (10M)
CAT6 Cable In 1080p 8-bit (45M), 12-bit (20M)
CAT6 Cable Out 1080p 8-bit (45M), 12-bit (20M)
HDMI Resolution 480i, ~ 1080p 50/60, 1080p 24, VGA ~ SXGA
IR Frequency 20 ~ 60KHz
ESD Protection Human body model: ± 8kV (air-gap discharge)
± 4kV (contact discharge)
Analogue Output port 4 x 3.5mm Stereo mini jack
Multi channel output ports 1 x Optical
Multi channel output audio
formats Dolby 5.1/2 and LPCM 2 channels
Power Supply 2 x 5V/2.6A DC (US/EU standards, CE/FCC/UL
certied)
Dimensions (mm) 80(W) x 72(D) x 30(H)
Weight (g) 760
Chassis Material Aluminium
Silk Skin Colour Black
Operating Temperature Operating from 0°C ~ 40°C

Notes:

www.cypeurope.com