CYP CHDBT-1H3CE User manual

DRAFT
CHDBT-1H3CE
1 by 4 HDMI over HDMI & CAT5e/6/7 with PoE
and Ethernet Transmitter
Operation Manual
Operation Manual

DRAFT
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. Cypress Technology assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies
that may be contained in this document. Cypress also makes no
commitment to update or to keep current the information contained
in this document.
Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means—
electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise—without express written permission and consent from
Cypress Technology.
© Copyright 2011 by Cypress Technology.
All Rights Reserved.
Version 1.0 September 2011
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.

DRAFT
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufcient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE
RDV1 27/02/13 Preliminary Release
RDV2 13/06/13 Package Contents
RDV3 17/06/13 Dimension
RDV4 20/06/13 Add IR Cable Pin Dene
RDV5 01/07/13 IR Power

DRAFT
CONTENTS
1. Introduction............................................1
2. Applications...........................................1
3. Package Contents ................................1
4. System Requirements............................1
5. Features..................................................2
6. Operation Controls and Functions.......3
6.1 Front Panel........................................3
6.2 Rear Panel.........................................4
6.3 IR Cable Pin Assignment..................5
7. Connection Diagram ...........................6
8. Specications ........................................7
8.1 CAT5e/6/7 Cable Specication .....8
9. Acronyms...............................................8

DRAFT
1
1. INTRODUCTION
The HDMI over HDMI and CAT5e/6/7 Transmitter can support
resolutions up to 1080p Full HD, 4Kx2K timing, 3D and multi-channel
digital audio formats to one HDTV and three CAT5e/6/7 outputs.
The HDMI can be connected to HDMI display for instant nearby
display and the CAT5e/6/7 can be connected to CAT5e/6/7 to HDMI
Receivers for distance up to 100 meters. Further, a total of 100Mbps
Ethernet transmission rate allows all connected device to share the
Ethernet service and the PoE function free the power shortage issue
from the Receiver end.
2. APPLICATIONS
• Household entertainment sharing and control
• Lecture room display and control
• Showroom display and control
• Meeting room presentation and control
• Classroom display and control
3. PACKAGE CONTENTS
• HDMI over HDMI & CAT5e/6/7 with PoE and Ethernet Transmitter
• IR Receiver x 1
• IR Blaster x 1
• 24V DC Power Adaptor
• Power Cord
• Operation Manual
4. SYSTEM REQUIREMENTS
• Source equipment with HDMI output connector
• Display TV/Monitor with HDMI input connector
• HDMI over CAT5e/6/7 Receivers with industry CAT5e/6/7 cables

DRAFT
2
5. FEATURES
• HDMI with 3D & 4Kx2K supported, HDCP and DVI compliant
• The HDMI and CAT5e/6/7 outputs are playing the same source
simultaneously
• Supports data rate from 250Mbps up to 3Gbps
• Supports wide range of PC resolutions from VGA to WUXGA
and HDTV resolutions up to 4Kx2K (3840x2160@30Hz and
4096x2160@24Hz)
• Supports LPCM 7.1CH, Dolby TrueHD, Dolby Digital Plus and DTS-HD
Master Audio transmission (32-192kHz sample rate)
• Supports distances up to 100 meters through CAT5e/6/7 cables
• Supports Ethernet transmission rate up to 100Mbps
• Can select Standard or TV EDID
• Supports USB service port
• The 3D signal display follow by display TV’s EDID
• Supports PoE with capable Receiver units
• Supports Bi-directional IR control
Note:
1. This system was tested with CAT6/23AWG cables, results may vary
 withcablesofadifferentspecication.
2. The PoE function is designed for powering compatible Receiver
units only non-PoE Receivers will need their own power supply.
Receivers of another brand may not be compatible.
3. Displaying HDMI 4Kx2K resolution require the standard 4Kx2K HDMI
cable and display in order for proper image displaying.

DRAFT
3
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
SYNC LINK EDID SERVICE
HDMI IN POWER
HDMI OUT
DC 24V
STDTV
1 2 3 4 5 6 87
1HDMI IN: Connect with source equipment such as DVD/Blu-ray or
PS3 player.
2SYNC: This LED will illuminate when the HDMI input port connected
to the source.
3HDMI OUT: Connect to HDMI display for instant image display or
cascade with another family type Transmitter.
4HDMI LINK: This LED will illuminate when HDMI output is connected
to TV or display monitor.
5EDID STD/TV: The default factory setting is on TV, leave as it is
when the display is properly. The unit will detect the 1st CAT5e/6/7
output’s EDID when it obtain a 4Kx2K EDID and send out the signal
accordingly to other output ports. If the 1st CAT5e/6/7 output is
without a 4Kx2K's EDID the unit will detect all output's EDID and
send out the signal that all outputs can accept.
This device obtain the last memory function therefore, the device
will use the last output port 1's EDID when output port 1 is not
connected to a display after power cycling or switch in between
the EDID setting.
Switch to STD to use build-in EDID if the display has problem. STD
EDID's video at 1080p@60Hz and audio at LPCM 2CH.
6SERVICE: This slot is reserved for factory service only.
7POWER LED: Once the power supply is connected the LED will
illuminate
8DC 24V: Plug the 24V DC power supply into the unit and connect
the adaptor to an AC outlet.

DRAFT
4
6.2 Rear Panel
MODE LINK MODE LINK MODE LINK
IR IN IR OUT LAN
23
1CAT5e/6/7 OUT
1 2 3 4 5
1IR IN: Connect with IR Extender to receive IR signal from Transmitter
side and blast out at Receiver side. Ensure that remote controller
being used is within he direct line-of-sight of the IR Extender.
2IR OUT: Connect with IR Blaster to blast out the IR signal received
from the Receiver side. Place the IR Baster in direct line-of-sight of
the equipment to be controlled.
3LAN: Connect to intra-net or internet service system for a total
sharing rate of 100Mbps within the link of Transmitter.
Warning: DO NOT connect this slot with any of the CAT5e/6/7 port,
doing so may trigger a power shot down and ruin the device.
4CAT5e/6/7 OUT 1~3: Connect these ports to CAT5e/6/7 to HDMI
Receivers (with or without PoE function) with CAT5e/6/7 cable to
extend the signal up to 100m.
5MODE & LINK 1~3: The Mode LED will illuminate when the device is
connected with power.
The link LED will illuminate when CAT5e/6/7 output(s) has been
connected to the Receiver(s) and the Receiver(s) has connected
with display that shows image on screen.

DRAFT
5
6.3 IR Cable Pin Assignment
3
1
3
1
2
2
Power 3.3V
IR Blaster Signal
NC
IR Signal
Power 3.3V
Grounding
IR Extender
IR Blaster

DRAFT
6
7. CONNECTION DIAGRAM
MODE LINK MODE LINK MODE LINK
IR IN IR OUT LAN 231CAT5e/6/7 OUT
SYNC LINKEDID SERVICE
HDMI IN POWER
HDMI OUT
DC 24V
STD TV
IR BLASTER
1.5m
60°
IR RECEIVER
7m
3m 3m
60°
m
CAT5e/6 In
Link
IR1 Extender
IR2 Blaster
Power
Blu-ray or PS3 Player
3D TV/Display
HDMI
Router (with
Internet
Connection)
HDMI