Cypress Semiconductor FM4-216-ETHERNET User manual

SHOW TITLE MM/DD/YY 1
FM4-216-ETHERNET
Hardware V1.0 / Documentation V1.3
Document Number: 002-09877 Rev. *A

SHOW TITLE MM/DD/YY 2
Warranty and Disclaimer
© Cypress Semiconductor Corporation, 2014-2017. This document is the property of Cypress Semiconductor Corporation and its subsidiaries, including
Spansion LLC (“Cypress”).This document, including any software or firmware included or referenced in this document (“Software”), is owned by Cypress
under the intellectual property laws and treaties of the United States and other countries worldwide. Cypress reserves all rights under such laws and treaties
and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other intellectual property rights.
If the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with Cypress governing the use of the
Software, then Cypress hereby grants you a personal, non-exclusive, nontransferable license (without the right to sublicense) (1) under its copyright rights in
the Software (a) for Software provided in source code form, to modify and reproduce the Software solely for use with Cypress hardware products, only
internally within your organization, and (b) to distribute the Software in binary code form externally to end users (either directly or indirectly through resellers
and distributors), solely for use on Cypress hardware product units, and (2) under those claims of Cypress’s patents that are infringed by the Software (as
provided by Cypress, unmodified) to make, use, distribute, and import the Software solely for use with Cypress hardware products. Any other use,
reproduction, modification, translation, or compilation of the Software is prohibited.
TO THE EXTENT PERMITTED BY APPLICABLE LAW, CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO
THIS DOCUMENT OR ANY SOFTWARE OR ACCOMPANYING HARDWARE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. To the extent permitted by applicable law, Cypress reserves the right to make
changes to this document without further notice. Cypress does not assume any liability arising out of the application or use of any product or circuit described
in this document. Any information provided in this document, including any sample design information or programming code, is provided only for reference
purposes. It is the responsibility of the user of this document to properly design, program, and test the functionality and safety of any application made of this
information and any resulting product. Cypress products are not designed, intended, or authorized for use as critical components in systems designed or
intended for the operation of weapons, weapons systems, nuclear installations, life-support devices or systems, other medical devices or systems (including
resuscitation equipment and surgical implants), pollution control or hazardous substances management, or other uses where the failure of the device or
system could cause personal injury, death, or property damage (“Unintended Uses”).A critical component is any component of a device or system whose
failure to perform can be reasonably expected to cause the failure of the device or system, or to affect its safety or effectiveness. Cypress is not liable, in
whole or in part, and you shall and hereby do release Cypress from any claim, damage, or other liability arising from or related to all Unintended Uses of
Cypress products. You shall indemnify and hold Cypress harmless from and against all claims, costs, damages, and other liabilities, including claims for
personal injury or death, arising from or related to any Unintended Uses of Cypress products.
Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, WICED, PSoC, CapSense, EZ-USB, F-RAM, and Traveo are
trademarks or registered trademarks of Cypress in the United States and other countries. For a more complete list of Cypress trademarks, visit cypress.com.
Other names and brands may be claimed as property of their respective owners.

SHOW TITLE MM/DD/YY 3
Overview
MCU Features, Board Features & Contents
Test it
The Hardware
The Jumper Table / Jumper Default
Board Power
Software Examples & Tools
Flash Programming
JTAG / CMSIS-DAP
IAR-Embedded Workbench
KEIL µVision
Additional documents
Schematics
Data sheet S6E2CC Series
Peripheral Manual
Timer part
Analog part
Communication part
Ethernet part
Flash programming manual

SHOW TITLE MM/DD/YY 4
Features of the S6E2CC Microcontroller
Package:
LQFP144, LQFP176 , BGA192 , LQFP 216,
ARM Cortex-M4 –CPU
200MHz (max)
2.7-5.5V
MPU, FPU
Ta= -40°C to +105°C
Main CLK: 4MHz
SUB CLK: 32kHz
MAIN RC CLK: 4MHz
SUB RC CLK: 100kHz
Subclock (option)
RC oscillator +/-2%
Clock Supervisor
Watch Counter
Low Voltage Detector 2ch
DMA
8ch
External IRQs
32ch + NMI
RTC
Y:M; h:m:s
S6E2CC9H/J/L
S6E2CC8H/J/L
12-bit ADC
ADT x 3ch FRTim x 3ch
OCU x 6ch ICU x 4ch
Waveform
Generator
Multi Function Timer
3ch
Dual Timer
12-bit ADC
12-bit ADC
QDU 4ch
S6E2CCAH/J/L
USB FS Host+Function 2ch
CAN (32 MSB) 2ch
CRC
Base Timer
16ch
Ethernet MAC 10/100MBit
PPG 9ch
SRAM
128K
FLASH
1MB
SRAM
192K
FLASH
1.5MB
SRAM
256K
FLASH
2MB
SWJ/TPIU/ETM Debug Ports
Resource
Pin Relocation
Quad SPI
CAN-FD 1ch
32ch
12-bit DAC
2ch
MFS(UART/SPI/I2C) 16ch
External Bus Interface
(SRAM, SDRAM, NAND, ..)
DSTC 256ch
Hardware Watchdog
I2S
SD Card I/F

SHOW TITLE MM/DD/YY 5
Features of the board
Features of the FM4-216-ETHERNET board:
•Microcontroller Cypress FM4 S6E2CCAL0A
•FM connect Ethernet: 1x IEEE802.3 Ethernet
•FM connect CAN: 2x CAN transceiver + 1x CAN-FD transceiver
•FM connect USB: 2x USB-Host (Type-A connector), 1x USB-Device (Type-B connector)
•FM touch: Slider using four ADC channels
•FM inverter: Motor-Control-Interface for e.g. POWER-3P-LV2-MC
•FM color: Cypress S/W TFT interface
•Cypress flash memory S25FL164K, connected via quad SPI interface
•I²S audio interface
•SD Card interface
•1x USB-to-serial converter (Type-B connector) using Cypress FM3 MB9AF312K
UART and on-board JTAG simultaneously (CMSIS DAP)
•Additional JTAG and Trace Interfaces each on a 20 pin-header
•2x Cypress Multicon flexible serial interface supporting I²C, SPI, UART, and LIN
•User interface
Backlit LCD module
5x pushbuttons (User buttons), potentiometer
1x Reset-button, Reset-LED
•All 216 pins routed to pin-header
•On-board 5V and 3V voltage regulators to supply MCU with separate Power-LEDs
•4x Power supply options: USB, USB-Device, JTAG or external 9V to 24V

SHOW TITLE MM/DD/YY 6
Contents FM4-216-ETHERNET
The FM4-216-ETHERNET box contains
•The FM4-216-ETHERNET evaluation board
•USB cable
•Ethernet cable
•CD: Documentation, software examples and development utilities
•1-page flyer
ESD foam ESD box FM4-216-ETHERNET USB, Ethernet cable
CD ROM Additional information
A B
RJ45 RJ45

SHOW TITLE MM/DD/YY 7
Test it
The microcontroller on the FM4-216-ETHERNET
is already preprogrammed with an example application (<drive:>\Examples\fm4-216-ethernet-tp_v12.srec).
Verify that jumpers JP75 and JP77 are set to 1-2 position and jumper JP76 is set to 3-4 position
Connect the FM4-216-ETHERNET via DEBUG USB port (X2) with the PC
Verify that switch S1 is set to RUN
Press the Reset-button
The FM4-216-ETHERNET‘s display will show a greeting message
Using the Up and Down pushbuttons will scroll through a menu on the LCD module
Connect X3 (static IP address 192.168.1.20) to a PC or local area network
Configure your PC to an untaken IP address within the same subnet (such as 192.168.1.42)
Point your webbrowser to board‘s IP address (192.168.1.20)
Install the USB Driver first <drive:>\drivers\driverinstaller.exe
Check the availibility for virtual COM port e.g. with Windows Device Manager
Open a serial terminal tool
e.g. Cypress Serial Port Viewer
<drive:>\tools\serialportviewer\setup.exe
Settings 115200 baud, 8N1
More board tests are available via serial console

SHOW TITLE MM/DD/YY 8
Test it
You finished successfully the first tests
Now you will get more details about the
FM4-216-ETHERNET
You will learn more about
•The on-board features
•How to program the Flash
•How to start with IAR-Embedded-Workbench and KEIL µVision

SHOW TITLE MM/DD/YY 9
Hardware

SHOW TITLE MM/DD/YY 10
The Hardware (Top Side) –Function Overview
Vin: 9..24V
DEBUG
CAN2 (FD) CAN1
USB Host
0/1
USB
Device
Ethernet
S6E2CCAL0A
Flash
Run/Prog
switch S1
Trace
JTAG
Reset
button
MultiCon 0/1
Variable
Resistor
Power
switch S2
CAN0
2x16 LCD Module
Five user buttons
FM touch
Audio Interface
MB9AF312K
Motion Control I/F
SD Card I/F
TFT Interface