Cypress CLUX-8M3D User manual

1x8 HDMI v1.3 Splitter
ID#15109
Operation Manual

Introduction
With eight HDMI outputs and capable of distributing 3D content the
HDMI v1.3 1 by 8 splitter is a forward looking device that helps you
handle futuristic technology today. ompatible with HDMI v1.3 which
defines the ability to transfer 3D content, Deep olor (10-bit and 12-bit)
video and new lossless compressed (Dolby TrueHD, Dolby Digital Plus
and DTS-HD Master Audio) digital audio, this device doesn’t merely
handle splitting and distributing, far from it, it also amplifies and equalizes
your signals to provide high performance I/O of audio and video.
Features
●HDMI v 1.3, HD P 1.1 and DVI 1.0 compliant receiver
●Deep color video up to 12bits, 1080p@24/60Hz
●Supports 3D content with an LED indicator to indicate if the video is
in standard definition or 3D.
●Allows one HDMI source to simultaneously connect with up to eight
HDMI displays
●HD P keysets allows each output to work independently when
connected to an HDMI display
●Transmits an HDMI source to eight outputs without any signal loss
●Supports DVI source / display by using an HDMI/DVI adaptor cable
●Supports LP M 7.1 H, Dolby TrueHD, Dolby Digital Plus and DTS-
HD master Audio transmission (32-192kHz sampling rate)
●Supports a wide range of P and HDTV resolutions from VGA to
WUXGA and 480i to 1080p
●HDMI cable distance testing showed that with 1080p/8bits resolution,
the input source can be 15 meters away and with 1080p/12bits it can
be 10 meters away.
●HDMI cable distance testing showed that with 1080p/8bits resolution,
the output source can be 15 meters away, and with 1080p/12bits it can
be 15 meters away.
pplications
●Display HDMI and 3D content
●Simultaneously display content on multiple screens.
●Retail store/ onference/Advertising display

Operation Controls
and Functions
Front Panel
1. HDMI OUT 7/8/1: Using HDMI cables connect these slots to displays
in order to show HDMI/3D content.
Note: When the input signal contains 3D data the display must support 3D
content in order to display an image.
. This system was tested with 24AWG cables if using cables of another
type, the performance of this system may be different.
B. able distance tested with a PS3 & 40” Samsung LED UA40B700 12
bits L D TV.
C. Figures provided in this manual are for reference only, actual figures
may depend on the source and display used along with the cables
specifications.
2. SYNC RED 3D ORG: This LED will turn red when the input signal is
not in 3D. If the input signal is 3D then the LED will change to orange.
3. HDMI IN: This slot connects with source devices such as DVD/Blu-
Ray players in order to receive an HDMI signal.
4. POWER LED & DC 5V: This slot is where you plug the 5V D power
supply into the unit and connect the adaptor to an A outlet. The LED will
switch on when power is ON.
Rear Panel
1. EDID switch STD/TV: This switch allows the user to choose the EDID
settings, the device must be turned on then off in order to make these
changes take effect. By switching to TV the device will read the EDID of
HDMI output 1 and will record it, then it will have the source send the
signal to the other seven HDMI outputs. The default setting is TV which
supports 3D content, leave as is when the display is working properly. By
switching to STD the device will use the built-in EDID, which is set at

1080p@60/12bits for video and LP M 2 h for audio, to allow the source
to send a signal to the connected displays.
2. HDMI OUT 2~6: Using HDMI cables connect these slots to displays in
order to show HDMI/3D content.
Note: When the input signal contains 3D data the display must also have
3D support in order to receive the signal.
3. SYS Reset ON/OFF: This switch allows the user to perform a system
reset. The default setting is OFF, leave as is when in normal use. By
switching ON, the unit will perform a reset every 8~10 minutes, in order to
perform this function the displays must have E support. When
performed successfully, the system will automatically switch the displays
to HDMI 1 input. The system reset will not perform on those displays that
do not have a E function.
Specifications
Video Bandwidth 225MHz/6.75Gbps
Input Port 1 x HDMI
Output Ports 8 x HDMI
ESD Protection Human body model
±8kV (air-gap discharge)
±6kV (contact discharge)
Power Supply 5V / 3A D (US/EU standards,
E/F /UL certified)
Dimensions(mm) 240 (W) x 103 (D) x 25(H)
Weight(g) 665
Chassis Material Metal
Silkscreen Color Black
Operating Temperature 0° ~40° / 32°F~104°F
Storage Temperature -20° ~60° / -4°F~140°F
Power Consumption 10W
Relative Humidity 20 ~ 90% RH (non-condensing)

Connection and
Installation