D-Link DAP-1360U User manual

Quick Installation Guide
DAP-1360U
Wireless N300 Access Point & Router

DAP-1360U Quick Installation Guide
BEFORE YOU BEGI
Delivery Package
•Access point DAP-1360U
•Power adapter DC 12V/0.5A
•Ethernet cab e
•Two detachab e antennas
•“Quick Installation Guide” (brochure).
If any of the items are missing, p ease contact your rese er.
The “User Manual” and “Quick Installation Guide” documents are avai ab e
on D-Link website (see www.d ink.ru).
!Using a power supply with a different voltage rating than the one
included will cause damage and void the warranty for this product.
Default Settings
IP address of access point 192.168.0.50
Username (login) admin
Password admin
ame of wireless network (SSID) DAP-1360
etwork key (PSK)
see WPS PIN on the
barcode abe on the
bottom pane of the
device
2

DAP-1360U Quick Installation Guide
System Requirements and Equipment
•A computer with any operating system that supports a web browser.
•A web browser to access the web-based interface of the access point:
◦App e Safari 8 and ater
◦Goog e Chrome 48 and ater
◦Microsoft Internet Exp orer 10 and ater
◦Microsoft Edge 20.10240 and ater
◦Mozi a Firefox 44 and ater
◦Opera 35 and ater.
•A NIC (Ethernet or Wi-Fi adapter) to connect to the access point.
•An 802.11b, g, or n Wi-Fi adapter to create a wire ess network.
3

DAP-1360U Quick Installation Guide
CO ECTI G TO PC
PC with Ethernet Adapter
1. Connect an Ethernet cab e between any of LAN ports ocated on the back
pane of the access point and the Ethernet port of your PC.
2. Connect the power cord to the power connector port on the back pane of
the access point, then p ug the power adapter into an e ectrica out et or
power strip.
3. Turn on the access point by pressing the ON/OFF button on its back
pane .
Now you need to configure an IP address for the Ethernet adapter of your PC.
4

DAP-1360U Quick Installation Guide
Configuring IP Address in S Windows 7
1. C ick the Start button and proceed to the Control Panel window.
2. Se ect the etwork and Sharing Center section. (If the Contro Pane
has the category view (the Category va ue is se ected from the View by
drop-down ist in the top right corner of the window), choose the View
network status and tasks ine under the etwork and Internet
section.)
3. In the menu ocated on the eft part of the window, se ect the Change
adapter settings ine.
4. In the opened window, right-c ick the re evant Local Area Connection
icon and se ect the Properties ine in the menu disp ayed.
5. In the Local Area Connection Properties window, on the
etworking tab, se ect the Internet Protocol Version 4 (TCP/IPv4)
ine. C ick the Properties button.
5

DAP-1360U Quick Installation Guide
6. Se ect the Use the following IP address radio button and enter the
va ue 192.168.0.51 in the IP address fie d. The Subnet mask
fie d wi be fi ed in automatica y. C ick the OK button.
7. C ick the OK button in the connection properties window.
Now you can connect to the web-based interface of DAP-1360U for
configuring a needed parameters. To gain access to an externa network (to
the Internet), you a so need to specify the defau t gateway and the addresses of
DNS servers.
6

DAP-1360U Quick Installation Guide
PC with Wi-Fi Adapter
1. Attach the antennas from the de ivery package. To do this, remove the
antennas from their wrapper, attach them to the re evant connectors on the
back pane of the access point, and then screw the antennas in a c ockwise
direction to the back pane . Position the antennas upward at their
connecting joints. This wi ensure optima operation of your wire ess
network.
2. Connect the power cord to the power connector port on the back pane of
the access point, then p ug the power adapter into an e ectrica out et or
power strip.
3. Turn on the access point by pressing the ON/OFF button on its back
pane .
4. Make sure that the Wi-Fi adapter of your PC is on. As a ru e, modern
notebooks with bui t-in wire ess NICs are equipped with a button or
switch that turns on/off the wire ess adapter (refer to your PC documents).
If your PC is equipped with a p uggab e wire ess NIC, insta the software
provided with your Wi-Fi adapter.
Now you shou d configure your Wi-Fi adapter.
7

DAP-1360U Quick Installation Guide
Configuring Wi-Fi Adapter in S Windows 7
1. C ick the Start button and proceed to the Control Panel window.
2. Se ect the etwork and Sharing Center section. (If the Contro Pane
has the category view (the Category va ue is se ected from the View by
drop-down ist in the top right corner of the window), choose the View
network status and tasks ine under the etwork and Internet
section.)
3. In the menu ocated on the eft part of the window, se ect the Change
adapter settings ine.
4. In the opened window, right-c ick the re evant Wireless etwork
Connection icon. Make sure that your Wi-Fi adapter is on, then se ect
the Properties ine in the menu disp ayed.
5. In the Wireless etwork Connection Properties window, on the
etworking tab, se ect the Internet Protocol Version 4 (TCP/IPv4)
ine. C ick the Properties button.
8

DAP-1360U Quick Installation Guide
6. Se ect the Use the following IP address radio button and enter the
va ue 192.168.0.51 in the IP address fie d. The Subnet mask
fie d wi be fi ed in automatica y. C ick the OK button.
7. C ick the OK button in the connection properties window.
8. To open the ist of avai ab e wire ess networks, se ect the icon of the
wire ess network connection and c ick the Connect To button or eft-
c ick the network icon in the notification area ocated on the right side of
the taskbar.
9

DAP-1360U Quick Installation Guide
9. In the opened window, in the ist of avai ab e wire ess networks, se ect the
wire ess network DAP-1360 and c ick the Connect button.
10. In the opened window, enter the network key (see WPS PIN on the
barcode abe on the bottom pane of the device) in the Security key
fie d and c ick the OK button.
11. Wait for about 20-30 seconds. After the connection is estab ished, the
network icon wi be disp ayed as the signa eve sca e.
Now you can connect to the web-based interface of DAP-1360U for configuring
a needed parameters. To gain access to an externa network (to the Internet), you
a so need to specify the defau t gateway and the addresses of DNS servers.
!
If you perform initia configuration of the access point via Wi-Fi
connection, note that immediate y after changing the wire ess defau t
settings of the access point you wi need to reconfigure the wire ess
connection using the new y specified settings.
10

DAP-1360U Quick Installation Guide
CO FIGURI G ACCESS POI T
Connecting to Web-based Interface
Start a web browser. In the address bar of the web browser, enter the domain
name of the access point (by defau t, dlinkap.local) with a dot at the end
and press the Enter key. A so you can enter the IP address of the device (by
defau t, 192.168.0.50).
!
If the error “ The page cannot be displayed ” (or “ Unable to display the
page ”/“ Could not connect to remote server ”) occurs upon connecting to
the web-based interface of the access point, make sure that you have
proper y connected the device to your computer.
If the device has not been configured previous y or the defau t settings have
been restored, after access to the web-based interface the Initia Configuration
Wizard opens (see the Initial Configuration Wizard section, page 14).
11

DAP-1360U Quick Installation Guide
If you configured the device previous y, after access to the web-based interface
the ogin page opens. Enter the username (admin) in the Username fie d
and the password you specified in the Password fie d, then c ick the LOGI
button.
If you enter a wrong password severa times, the web-based interface wi be
b ocked for a whi e. P ease wait for one minute and reenter the password you
specified.
12

DAP-1360U Quick Installation Guide
The Summary page disp ays genera information on the access point and its
software.
The web-based interface of the access point is bi ingua (Eng ish/Russian).
You can se ect the needed anguage upon the initia configuration of the web-
based interface of the access point or in the System / Configuration section
of the menu.
Other settings of the access point are avai ab e in the menu in the eft part of
the page. Go to the re evant section and se ect the needed page or run the
wizard in the Initial Configuration section.
13

DAP-1360U Quick Installation Guide
Initial Configuration Wizard
In order to start the Initia Configuration Wizard manua y, go to the Initial
Configuration section.
C ick the OK button and wait unti the factory defau t settings are restored.
If you perform initia configuration of the access point via Wi-Fi connection,
p ease make sure that you are connected to the wire ess network of DAP-
1360U (see the WLAN name (SSID) in the Default Settings section, page 2)
and c ick the EXT button. Then c ick the START button.
If the device has not been configured previous y or the defau t settings have
been restored, the Initia Configuration Wizard starts automatica y upon
access to the web-based interface or upon opening a web site on the Internet.
14

DAP-1360U Quick Installation Guide
1. C ick YES in order to eave the current anguage of the web-based
interface or c ick O to se ect the other anguage.
2. On the next page, c ick the CO TI UE button.
15

DAP-1360U Quick Installation Guide
Selecting Connection Method
In order to connect your device to a wired router for adding a wire ess network
to the existing oca network, on the Device mode page, from the
Connection method ist, se ect the Wired connection va ue. Then from
the Work mode ist se ect the Access point va ue. In this mode you can
change the LAN IP address, set your own settings for the wire ess network and
set your own password for access to the web-based interface of the device.
In order to connect your device to a wire ess router for extending the range of
the existing wire ess network, on the Device mode page, from the
Connection method ist, se ect the Wi-Fi va ue. Then from the Work
mode ist se ect the Repeater va ue. In this mode you can change the LAN
IP address, connect your device to another access point, set your own settings
for the wire ess network, and set your own password for access to the web-
based interface of the device.
In order to et wired PCs connected to your device access the network of a
wire ess router, on the Device mode page, from the Connection method
ist, se ect the Wi-Fi va ue. Then from the Work mode ist se ect the Client
va ue. In this mode you can change the LAN IP address, connect your device
to another access point and set your own password for access to the web-based
interface of the device.
16

DAP-1360U Quick Installation Guide
A so you can enab e the WDS function via the Initia Configuration Wizard.
To do this, on the Device mode page, from the Connection method ist,
se ect the Wi-Fi va ue. Then from the Work mode ist se ect the WDS va ue.
In this mode you can specify the WDS function parameters, change the LAN
IP address, set your own settings for the wire ess network, and set your own
password for access to the web-based interface of the device.
In order to connect your device to a wired ISP, on the Device mode page,
from the Connection method ist, se ect the Wired connection va ue.
Then from the Work mode ist se ect the Router va ue. In this mode you can
configure a WAN connection, set your own settings for the wire ess network,
configure LAN ports to connect an STB or VoIP phone, and set your own
password for access to the web-based interface of the device.
In order to connect your device to a wire ess ISP (WISP), on the Device
mode page, from the Connection method ist, se ect the Wi-Fi va ue.
Then from the Work mode ist se ect the WISP Repeater va ue. In this
mode you can connect your device to another access point, configure a WAN
connection, set your own settings for the wire ess network, configure LAN
ports to connect an STB or VoIP phone, and set your own password for access
to the web-based interface of the device.
When the operation mode is se ected, c ick the EXT button.
17

DAP-1360U Quick Installation Guide
Conguring WDS Function
This configuration step is avai ab e for the WDS mode.
1. On the WDS page, in the WDS Mode ist, se ect the WDS function
mode.
2. In the WDS Encrytion ist, se ect a type of encryption for data transfer
between access points interconnected via the WDS function. Then enter a
key for the specified type of encryption in the Encryption Key fie d (a
password that wi be used to access the wire ess network between the
interconnected access points). When the Without encryption va ue is
se ected, traffic between the access points wi not be secured.
3. In the Channel ist, se ect the wire ess channe number. The same
wire ess channe for the interconnected access points shou d be specified.
18

DAP-1360U Quick Installation Guide
4. In the AP MAC fie d, specify the MAC address of a device connected to
the access point via the WDS function. To specify severa MAC
addresses, c ick the ADD button, and in the ine disp ayed, enter a MAC
address.
!The WDS function parameters must be the same for a interconnected
devices.
5. C ick the EXT button.
19

DAP-1360U Quick Installation Guide
Changing LAN IPv4 Address
This configuration step is avai ab e for the Access point, WDS, Repeater,
and Client modes.
1. Se ect the Automatic obtainment of IPv4 address to et DAP-
1360U automatica y obtain the LAN IPv4 address.
2. In the Hostname fie d, you shou d specify a domain name of the access
point using which you can access the web-based interface after finishing
the Wizard. Enter a new domain name of the access point ending with
.local or eave the va ue suggested by the access point.
!In order to access the web-based interface using the domain name, i n the
address bar of the web browser, enter the name of the access point with a
dot at the end.
If you want to manua y assign the LAN IPv4 address for DAP-1360U, do not
se ect the Automatic obtainment of IPv4 address checkbox and fi in
the IP address, etmask, Hostname fie ds and, if needed, the Gateway
IP address fie d. Make sure that the assigned address does not coincide with
the LAN IPv4 address of the router to which your device connects.
3. After changing the LAN IPv4 address of the device, make sure that the
network adapter settings correspond to the new parameters.
4. C ick the EXT button.
20