D-Link DGS-2208 - Desktop Switch User manual

2D-Link DGS-2208 User Manual
Table of Contents
Safety Instructions ...................................................... 3
Safety Cautions ....................................................... 3
Protecting Against Electrostatic Discharge.............. 6
Product Overview........................................................7
Package Contents ................................................... 7
Setup ....................................................................... 7
Introduction.............................................................. 8
Features ................................................................ 11
Hardware Overview ............................................... 12
Front Panel (LEDs) .......................................... 12
Rear Panel (Connections) ............................... 14
Installation..................................................................15
Before You Connect to the Network ......................15
Mounting the Switch on the Wall ........................... 16
Mounting on a cement wall .............................. 16
Mounting on a wood wall .................................16
Connecting the Switch...........................................17
DGS-2208 to End Node...................................17
Hub/Switch to DGS-2208.................................17
Connecting To Network Backbone or Server .. 17
Troubleshooting ........................................................18
Glossary .....................................................................19
Networking Basics ....................................................24
Check your IP address .......................................... 24
Windows®XP/2000 Users................................ 24
Windows Vista™Users..................................... 24
Statically Assign an IP address ............................. 25
Windows®XP/2000 Users................................ 25
Windows Vista™Users..................................... 26
Technical Specications........................................... 27
DGS-2208 Specications ...................................... 27
Contacting Technical Support ................................. 29
Warranty..................................................................... 30
Registration................................................................35
Table of Contents

3D-Link DGS-2208 User Manual
Section 1 - Safety Instructions
Use the following safety guidelines to ensure your own personal safety and to help protect your system from potential
damage.
Safety Cautions
To reduce the risk of bodily injury, electrical shock, re, and damage to the equipment, observe the following
precautions.
Observe and follow service markings. Do not service any product except as explained in your system documentation.
Opening or removing covers that are marked with the triangular symbol with a lightning bolt may expose you to an
electrical shock. Only a trained service technician should service components inside these compartments.
If any of the following conditions occur, unplug the product from the electrical outlet and replace the part or contact
your trained service provider:
– The power cable, extension cable, or plug is damaged.
– An object has fallen into the product.
– The product has been exposed to water.
– The product has been dropped or damaged.
– The product does not operate correctly when you follow the operating instructions.
• Keep your system away from radiators and heat sources. Also, do not block cooling vents.
• Do not spill food or liquids on your system components, and never operate the product in a wet environment. If
the system gets wet, see the appropriate section in your troubleshooting guide or contact your trained service
provider.
Safety Instructions

4D-Link DGS-2208 User Manual
Section 1 - Safety Instructions
• Do not push any objects into the openings of your system. Doing so can cause a re or an electric shock by
shorting out interior components.
• Use the product only with approved equipment.
• Allow the product to cool before removing covers or touching internal components.
• Operate the product only from the type of external power source indicated on the electrical ratings label. If you
are not sure of the type of power source required, consult your service provider or local power company.
• To help avoid damaging your system, be sure the voltage selection switch (if provided) on the power supply is
set to match the power available at your location:
– 115 volts (V)/60 hertz (Hz) in most of North and South America and some Far Eastern countries such
as South Korea and Taiwan.
– 100 V/50 Hz in eastern Japan and 100 V/60 Hz in western Japan.
– 230 V/50 Hz in most of Europe, the Middle East, and the Far East.
• Also be sure that attached devices are electrically rated to operate with the power available in your location.
• Use only approved power cable(s). If you have not been provided with a power cable for your system or for
any AC-powered option intended for your system, purchase a power cable that is approved for use in your
country. The power cable must be rated for the product and for the voltage and current marked on the product’s
electrical ratings label. The voltage and current rating of the cable should be greater than the ratings marked
on the product.
• To help prevent an electric shock, plug the system and peripheral power cables into properly grounded electrical
outlets. These cables are equipped with three-prong plugs to help ensure proper grounding. Do not use adapter
plugs or remove the grounding prong from a cable. If you must use an extension cable, use a 3-wire cable with
properly grounded plugs.

5D-Link DGS-2208 User Manual
Section 1 - Safety Instructions
• Observe extension cable and power strip ratings. Make sure that the total ampere rating of all products plugged
into the extension cable or power strip does not exceed 80 percent of the ampere ratings limit for the extension
cable or power strip.
• To help protect your system from sudden, transient increases and decreases in electrical power, use a surge
suppressor, line conditioner, or uninterruptible power supply (UPS).
• Position system cables and power cables carefully; route cables so that they cannot be stepped on or tripped
over. Be sure that nothing rests on any cables.
• Do not modify power cables or plugs. Consult a licensed electrician or your power company for site modications.
Always follow your local/national wiring rules.
• When connecting or disconnecting power to hot-pluggable power supplies, if offered with your system, observe
the following guidelines:
– Install the power supply before connecting the power cable to the power supply.
– Unplug the power cable before removing the power supply.
– If the system has multiple sources of power, disconnect power from the system by unplugging all power
cables from the power supplies.
• Move products with care; ensure that all casters and/or stabilizers are rmly connected to the system. Avoid
sudden stops and uneven surfaces.

6D-Link DGS-2208 User Manual
Section 1 - Safety Instructions
Static electricity can harm delicate components inside your system. To prevent static damage, discharge static electricity
from your body before you touch any of the electronic components, such as the microprocessor. You can do so by
periodically touching an unpainted metal surface on the chassis.
You can also take the following steps to prevent damage from electrostatic discharge (ESD):
1. When unpacking a static-sensitive component from its shipping carton, do not remove the component
from the antistatic packing material until you are ready to install the component in your system. Just
before unwrapping the antistatic packaging, be sure to discharge static electricity from your body.
2. When transporting a sensitive component, rst place it in an antistatic container or packaging.
3. Handle all sensitive components in a static-safe area. If possible, use antistatic oor pads, workbench
pads, and an antistatic grounding strap.
Protecting Against Electrostatic Discharge

7D-Link DGS-2208 User Manual
Section 2 - Product Overview
• D-Link DGS-2208 8-port Switch
• Manual and Warranty on CD
• Four (4) Rubber Feet
• Wall Mount Kit
• Power Adapter
Setup
The setup of the DGS-2208 can be performed using the following steps:
• The power outlet should be within 1.82 meters (6 feet) of the Switch.
• Visually inspect the DC power jack and make sure that it is fully secured to the power adapter.
• Do not cover the ventilation holes on the sides of the Switch, and make sure there is adequate ventilation
around it.
• Do not place heavy objects on the switch.
Product Overview
Package Contents

8D-Link DGS-2208 User Manual
Section 2 - Product Overview
Introduction
D-Link Green Ethernet Technology
D-Link Green Ethernet Technology implements special power-saving features under speed at 1000Mbps that detect
cable length and link status and adjust power usage accordingly.
Green Ethernet Technology saves energy in two specic ways:
1. If there is no link on a port (when there is no connection or the device connected is turned off) the port(s)
will enter a “sleep mode” which will drastically reduce the amount of power used.
2. D-Link Green Ethernet Technology detects the length of connected Ethernet cable and adjusts power
usage accordingly without affecting performance. This way, a port connected to a 10m cable only uses
as much power as it needs, instead of using full power, which is only needed for 100m cables.
Fast Ethernet Technology
The growing importance of LANs and the increasing complexity of desktop computing applications are fueling the need
for high performance networks. 100BASE-TX (Fast Ethernet) provides a cost-effective and high-performance solution for
small workgroups, SMBs (Small to Medium Businesses), and any network supporting bandwidth-intensive applications.
Fast Ethernet technology operates at 10 times the speed of traditional Ethernet, offering maximum performance and
enhanced capability for existing Ethernet-based networks.
100Mbps Fast Ethernet is a standard specied by the IEEE 802.3 LAN committee. It is an extension of the 10Mbps
Ethernet standard with the ability to transmit and receive data at 100Mbps, while maintaining the CSMA/CD Ethernet
protocol. Since the 100Mbps Fast Ethernet is compatible with all other 10Mbps Ethernet environments, it provides
a straightforward upgrade and takes advantage of the existing investment in hardware, software, and personnel
training.

9D-Link DGS-2208 User Manual
Section 2 - Product Overview
Gigabit Ethernet Technology
Gigabit Ethernet is an extension of IEEE 802.3 Ethernet utilizing the same packet structure, format, and support
for CSMA/CD protocol, full duplex, ow control, and management objects, but with a tenfold increase in theoretical
throughput over 100Mbps Fast Ethernet and a one hundred-fold increase over 10Mbps Ethernet. Since it is compatible
with all 10Mbps and 100Mbps Ethernet environments, Gigabit Ethernet provides a straightforward upgrade without
wasting a company’s existing investment in hardware, software, and trained personnel.
The increased speed and extra bandwidth offered by Gigabit Ethernet are essential to coping with the network bottlenecks
that frequently develop as computers and their busses get faster and more users use applications that generate more
trafc. Upgrading key components, such as your backbone and servers to Gigabit Ethernet can greatly improve network
response times as well as signicantly speed up the trafc between your subnetworks.
Gigabit Ethernet enables fast optical ber connections to support video conferencing, complex imaging, and similar
data-intensive applications. Likewise, since data transfers occur 10 times faster than Fast Ethernet, servers outtted
with Gigabit Ethernet NIC’s are able to perform 10 times the number of operations in the same amount of time.
In addition, the phenomenal bandwidth delivered by Gigabit Ethernet is the most cost-effective method to take advantage
of today and tomorrow’s rapidly improving switching and routing internetworking technologies.
Switching Technology
Switching is a cost-effective way of increasing the total network capacity available to users on a LAN. If an Ethernet
network begins to display symptoms of congestion, low throughput, slow response times, and high rates of collision,
installing a switch to a network can preserve much or all of the existing network’s cabling and workstation interface card
infrastructure, while still greatly enhancing the throughput for users. A switch is a viable solution even if demanding
applications, such as multimedia production and video conferencing, are on the horizon. The most promising techniques,
as well as the best return on investment, could well consist of installing the right mixture of Ethernet switches.
A switch increases capacity and decreases network loading by dividing a local area network into different LAN
segments. Dividing a LAN into multiple segments is one of the most common ways of increasing available bandwidth.
If segmented correctly, most network trafc will remain within a single segment, enjoying the full-line speed bandwidth
of that segment.

10D-Link DGS-2208 User Manual
Section 2 - Product Overview
Switches provide full-line speed and dedicated bandwidth for all connections. This is in contrast to hubs, which use
the traditional shared networking topology, where the connected nodes contend for the same network bandwidth.
When two switching nodes are communicating, they are connected with a dedicated channel between them, so there
is no contention for network bandwidth with other nodes. As a result, the switch reduces considerably, the likelihood
of trafc congestion.
For Ethernet networks, a switch is an effective way of eliminating the problem of chaining hubs beyond the “two-repeater
limit.” A switch can be used to split parts of the network into different collision domains, making it possible to expand
your Ethernet network beyond the 205-meter network diameter limit for 100BASE-TX networks. Switches supporting
both 10Mbps Ethernet and 100Mbps Fast Ethernet are also ideal for bridging between existing 10Mbps networks and
newer 100Mbps networks.
Switching LAN technology is a marked improvement over the previous generation of network hubs and bridges, which
were characterized by higher latencies. Routers have also been used to segment local area networks, but the cost of
a router, the setup and maintenance required, make routers relatively impractical. Today switches are an ideal solution
to most kinds of local area network congestion problems.
802.1p Priority Tagging
802.1p places a tag in a frame to indicate the priority of the frame. A tag will represent a priority of 0-7 and an 802.1p
compliant switch can read this tag and prioritize trafc accordingly. In 802.1p a port can receive frames with varying
priority tags and classify them based on these tags. A VoIP phone that supports 802.1p can assign a priority to its
VoIP trafc and when it enters the switch the switch can give it a higher priority so that voice trafc is always clear and
jitter free. The DGS-2208 supports the 802.1p feature with 4 precongured priority queues. When a frame tagged with
an 802.1p priority bit is received by the switch it places the frame into one of 4 queues prioritized according to its tag
number. For example, trafc tagged with a priority bit of 7 will have a higher priority then trafc tagged with a priority
bit of 6 and so forth.
Jumbo Frame Support
The DGS-2208 switch supports Jumbo Frames up to (9720 Bytes) in size. Jumbo Frame support is designed to improve
network throughput and signicantly reduce the CPU utilization of large le transfers such as multimedia les or large
data les by enabling more efcient larger payloads per packet.

11D-Link DGS-2208 User Manual
Section 2 - Product Overview
Features
The DGS-2208 8-port 10/100/1000BASE-T Gigabit Ethernet Switch was designed for easy installation and high
performance in an environment where trafc on the network and the number of users increase continuously.
• D-Link’s “Green Ethernet” Technology
• Eight (8) 10/100/1000BASE-T Gigabit Ethernet ports
• Supports Auto-Negotiation for 10/100/1000Mbps and duplex mode
• Supports Auto-MDI/MDIX for each port
• Supports Full/Half duplex transfer mode for 10 and 100Mbps
• Supports Full-duplex transfer mode for 1000Mbps
• Supports IEEE 802.1p Priority Queuing, up to 4 queues
• Full wire speed reception and transmission
• Store-and-Forward switching method
• Supports 4K MAC addresses
• Extensive front-panel diagnostic LEDs
• Jumbo frame support (9720 Bytes in 1000Mbps only)
• IEEE 802.3x ow control for full duplex
• Back pressure ow control for half duplex

12D-Link DGS-2208 User Manual
Section 2 - Product Overview
Hardware Overview
Front Panel (LEDs)
The LED indicators of the Switch include Power, 100/1000Mbps, and Link/Act. The following shows the LED indicators
for the Switch along with an explanation of each indicator.
LED Indicators:
Comprehensive LED indicators display the conditions of the Switch and status of the network. A description of these
LED indicators follows (see LED Indicators). The LED indicators of the Switch include Power, Link/Act, 1000Mbps,
and 100Mbps.

13D-Link DGS-2208 User Manual
Section 2 - Product Overview
Power Indicator
This green indicator illuminates when the Switch is receiving power.
Link/Act
This green indicator illuminates steadily when a port is connected to a station successfully and has a good link. The
indicator will blink to indicate that a port is transmitting or receiving data on the network.
Speed − 1000Mbps/Green; 100Mbps/Amber; 10Mbps/Off
This indicator is amber-colored when the port is connected to a 100Mbps Fast Ethernet station. It is green when the
port is connected to a 1000Mbps Ethernet station. It is not illuminated when the port is connected to a 10Mbps Ethernet
station.

14D-Link DGS-2208 User Manual
Section 2 - Product Overview
Rear Panel (Connections)
Auto MDI/MDI-X Ports:
Eight (8) Gigabit Ethernet, Auto-Negotiating ports (10/100/1000Mbps) Comprehensive LED indicators display the
conditions of the Switch and status of the network.
DC Power Jack:
Power is supplied through an external AC power adapter. Check the technical specication section for information
about the AC power input voltage.
Since the DGS-2208 does not require a power button, plugging its power adapter into a power outlet will immediately
power it on.

15D-Link DGS-2208 User Manual
Section 3 - Installation
Installation
This section will explain how to connect Ethernet devices to your new D-Link switch and how to mount the switch.
Before You Connect to the Network
The site where you install the Switch may greatly affect its performance. Please follow these guidelines for setting up
the Switch.
• Install the Switch on a sturdy, level surface that can support at least 3 kg (6.6 lbs.) of weight. Do not place
heavy objects on the Switch.
• The power outlet should be within 1.82 meters (6 feet) of the Switch.
• Visually inspect the power cord and see that it is fully secured to the AC power port.
• Make sure that there is adequate space for proper heat dissipation from and adequate ventilation around
the Switch. Leave at least 10 cm (4 inches) of space at the front and rear of the Switch for ventilation.
• Install the Switch in a fairly cool and dry place for the acceptable temperature and humidity operating
ranges.
• Install the Switch in a site free from strong electromagnetic eld generators (such as motors), vibration,
dust, and direct exposure to sunlight.
• When installing the Switch on a level surface, attach the rubber feet to the bottom of the device. The
rubber feet cushion the Switch, protect the casing from scratches, and prevent it from scratching other
surfaces.

16D-Link DGS-2208 User Manual
Section 3 - Installation
Mounting the Switch on the Wall
The DGS-2208 can also be mounted on a wall. Two mounting slots are provided on the bottom of the switch for this
purpose. Please make sure that the front panel is exposed in order to view the LEDs. Please refer to the illustration
below:
Mounting on a cement wall
1. Mount the Nylon screw anchors into a cement wall.
2. Drive the T3 x 15L screws into the Nylon screw anchors.
3. Hook the mounting holes of the switch back on the screws.
Mounting on a wood wall
1. Drive the T3 x 15 L screws into the wood wall.
2. Hook the mounting holes of the switch back on the screws.
(1) 3/4 inch minimum for wood wall
(2) 3 inch minimum for cement wall.

17D-Link DGS-2208 User Manual
Section 3 - Installation
Connecting the Switch
DGS-2208 to End Node
End nodes include PCs outtted with a 10, 100, or 1000 Mbps RJ-45 Ethernet Network Interface Card (NIC)
and most routers. An end node can be connected to the Switch via a twisted-pair Category 3, 4, 5, or 5e
UTP/STP cable. The end node can be connected to any of the ports of the Switch.
The Link/Act LEDs for each UTP port light green when the link is valid. The LED over the port label indicates a port
speed of either 10/100 Mbps or 1000Mbps. A blinking LED on the bottom indicates packet activity on that port.
Hub/Switch to DGS-2208
These connections can be accomplished in a number of ways using a standard Ethernet cable.
• A 10BASE-T hub or switch can be connected to the Switch via a twisted-pair Category 3, 4, 5, or 5e
UTP/STP cable.
• A 100BASE-TX hub or switch can be connected to the Switch via a twisted -pair Category 5 UTP/STP
cable.
• A 1000BASE-T switch can be connected to the Switch via a twisted -pair Category 5e or better UTP/
STP cable.
Connecting To Network Backbone or Server
Any of the eight Gigabit Ethernet ports are ideal for uplinking to a network backbone or network server.

18D-Link DGS-2208 User Manual
Section 4 - Troubleshooting
Troubleshooting
1. Why can´t I share my Internet connection to multiple computers when using my D-Link DGS-2208 switch?
If you are connecting directly to a Cable or DSL modem, you will need a router to “share” your Internet connection or
a computer using ICS (Internet Connection Sharing) or Proxy. Switches and hubs do not allow you to share a single
IP address to multiple computers.
Another alternative is to contact your ISP and purchase extra IP addresses for each additional computer.
2. Does the DGS-2208 switch have an uplink port?
The DGS-2208 has Auto-MDI ports which automatically sense the type of cable being used (e.g. Straight-through or
Crossover) and adjust themselves accordingly to pass data over the network.
3. What is the maximum length of Category 3, 4 or 5 twisted pair cable that can be used between the DGS-2208
and other devices such as routers, switches, computers, etc.?
The maximum length of Category 3, 4 or 5 twisted pair cable that can be used between computers and other devices
on a network is 100 meters or about 328 feet. Keep in mind that this is a theoretical limit. Usually, you will want to keep
the distance between devices well below the limit.

19D-Link DGS-2208 User Manual
Section 5 - Glossary
Glossary
1000BASE-T
A specication for Gigabit Ethernet over copper (IEEE 802.3ab). The standard denes 1 Gbps data transfer over
distances of up to 100 meters using 4 pairs of CAT-5 balanced copper cabling and a 5-level coding scheme. Its benets
include compatibility with existing network protocols (i.e. IP, IPX, AppleTalk), existing applications, Network Operating
Systems, network management platforms and applications.
100BASE-TX
100Mbps Ethernet implementation over Category 5 and Type 1 Twisted Pair cabling.
10BASE-T
The IEEE 802.3 specication for Ethernet over Unshielded Twisted Pair (UTP) cabling.
aging
The automatic removal of dynamic entries from the Switch Database which have timed-out and are no longer valid.
auto-negotiation
A feature on a port, which allows it to advertise its capabilities for speed, duplex, and ow control. When connected to
an end station that also supports auto-negotiation, the link can self-detect its optimum operating setup.
backbone port
A port that does not learn device addresses, and that receives all frames with an unknown address. Backbone ports
are normally used to connect the Switch to the backbone of your network. Note that backbone ports were formerly
known as designated downlink ports.
backbone
The part of a network used as the primary path for transporting trafc between network segments.

20D-Link DGS-2208 User Manual
Section 5 - Glossary
Bandwidth
Information capacity, measured in bits per second, that a channel can transmit. The bandwidth of Ethernet is 10Mbps,
the bandwidth of Fast Ethernet is 100Mbps.
BOOTP
The BOOTP protocol allows you to automatically map an IP address to a given MAC address each time a device is
started. In addition, the protocol can assign the subnet mask and default gateway to a device.
bridge
A device that interconnects local or remote networks no matter what higher level protocols are involved. Bridges form
a single logical network, centralizing network administration.
broadcast
A message sent to all destination devices on the network.
broadcast storm
Multiple simultaneous broadcasts that typically absorb available network bandwidth and can cause network failure.
console port
The port on the Switch accepting a terminal or modem connector. It changes the parallel arrangement of data
within computers to the serial form used on data transmission links. This port is most often used for dedicated local
management.
data center switching
The point of aggregation within a corporate network where a switch provides high performance access to server farms,
a high-speed backbone connection, and a control point for network management and security.
Ethernet
A LAN specication developed jointly by Xerox, Intel, and Digital Equipment Corporation. Ethernet networks operate
at 10Mbps using CSMA/CD to run over cabling.