D-Link DI-704GU User manual

Wireless G USB 2.0 Adapter
Wireless Internet Camera
with 3G Mobile Video

2D-Link DI-704GU Quick Install Guide
System Requirements
• Ethernet-based Cable or DSL Modem
• Computers with Windows®, Macintosh®, or Linux-based operating
systems with an installed Ethernet adapter
• Internet Explorer 6.x and above, or Netscape®Navigator 7.0 and
above
Package Contents
D-Link DI-704GU
Gigabit QoS Router
System Requirements
If any of the above items are missing, please contact your reseller.
CAT5 Ethernet Cable Power Adapter
CD-ROM with
Manual

3 D-Link DI-704GU Quick Install Guide
Hardware Overview
Hardware Overview
Power LED
A solid light indicates a
proper connection to the
power supply.
USB LED
A solid light indicates a connection
to the USB port. This LED blinks
during data transmission.
Status LED
A blinking light indicates that
the DI-704GU is functioning
properly.
Local Network LEDs
A solid light on each port
indicates a connection to an
Ethernet enabled device.
These LEDs blink during data
transmission.
WAN LED
A solid light indicates a connection
on the WAN port. This LED blinks
during data transmission.

4D-Link DI-704GU Quick Install Guide
Hardware Overview
USB Port
Connection for a USB printer.
LAN Ports
These are the connections for Ethernet cables to
Ethernet-enabled computers.
Power Receptor
WAN Port
This is for the connection of an Ethernet
cable to your Cable or DSL modem.
Reset Button
Pressing this button restores the Router to
its original factory default settings.

5 D-Link DI-704GU Quick Install Guide
Hardware Installation
Hardware Installation
A. First, connect the power adapter to the receptor at the back panel
of the DI-704GU and then plug the other end of the power adapter
to a wall outlet or power strip. The Power LED will turn ON to
indicate proper operation.
B.1.Power off your Cable or DSL modem; some devices may not have
a on/off switch and will require you to unplug the power adapter.
Now, the DI-704GU should be powered on and the Cable/DSL
modem should be turned off.
2.Cable/DSL modem (Power Off) – DI-704GU (Power On) Connect
an Ethernet cable to the Ethernet jack located on the Cable/DSL
modem. After the Ethernet cable is securely connected, power on
the Cable/DSL modem by turning on the unit or plugging in the
power adapter.
3. Cable/DSL modem (Power On) – DI-704GU (Power On) Insert
the other end of the Ethernet cable to the WAN PORT on the
back panel of the DI-704GU. The WAN LED light will illuminate
to indicate proper connection. If the WAN LED is not illuminated,
please go back to step B1 and repeat the instructions.
C.Insert an Ethernet cable to LAN port 1 on the back panel of the
DI-704GU and an available Ethernet port on the network adapter
in the computer you will use to configure the DI-704GU. The LED
light for LAN Port 1 will illuminate to indicate proper connection.
Note: The LAN Ports on the DI-704GU are Auto-MDI/MDIX.Which
means you can use straight-through or crossover Ethernet cables
to connect to the LAN Ports.
D.Computers equipped with Ethernet or Gigabit Ethernet adapters
will be able to connect to the DI-704GU.The DFE-530TX or DGE-
530T PCI Adapters (as examples) will be able to connect with the
router without any additional configuration required.

6D-Link DI-704GU Quick Install Guide
Getting Started
Getting Started Configuration

7 D-Link DI-704GU Quick Install Guide
Configuration
This section will show you how to configure your new D-Link Gigabit
QoS Router using the D-Link Setup Wizard.
Configuration
Click Log In
Click Run Wizard
Open your Web browser and type
“http://192.168.0.1” into the URL
address box.Then press the Enter
or Return key.
Select “Admin” from the
User Name drop down menu
and leave the password field
blank.

8D-Link DI-704GU Quick Install Guide
Configuration
Click Next
Click Next
Click Next
You have the option to establish
a password for the User Name
“Admin”.
Choose your time zone from the
drop down list.

9 D-Link DI-704GU Quick Install Guide
Configuration
You will be prompted to select the type of Internet connection for your
router. If you are unsure of which setting to select, please contact
your Internet Service Provider.
Static IP Address - page 10
PPPoE - page 11
PPTP - page 12
L2TP - page 13
Big Pond - page 14
If you selected Dynamic IP Address, this screen will appear: (Used
mainly for Cable Internet service).
Click Next
Dynamic IP Address
Click Next
Continue to page 15
Click the “Clone MAC Address”
button to automatically copy the
MAC address of the network
adapter in your computer. You
can also manually type in the
MAC address.

10D-Link DI-704GU Quick Install Guide
Configuration
If your ISP requires a Static
IP Address, please select the
corresponding radio button.
Enter the IP address that
was originally provided to you
by your ISP. You will need to
complete all of the required
fields.
Click Next
Static IP Address
Click Next
Continue to page 15

11 D-Link DI-704GU Quick Install Guide
Configuration
If your ISP uses PPPoE
(Point-to-Point Protocol
over Ethernet), select the
corresponding radio button.
If you have a Dynamic IP
connection, enter the User
Name and Password provided
to you by your ISP.
PPPoE
Click Next
Click Next
Continue to page 15
Note: Please be sure to remove any existing PPPoE client software
installed on your computers.

12D-Link DI-704GU Quick Install Guide
Configuration
If your ISP uses PPTP (Point
to Point Tunneling Protocol),
select the corresponding radio
button.
If you have a Dynamic IP
connection, enter the Server IP,
PPTP Account, and Password
provided to you by your ISP.
If yo u have a Static I P
connection, enter the IP
Address, Subnet Mask,
Gateway IP Address, Server IP,
PPTP Account, and Password
provided to you by your ISP.
PPTP
Click Next
Click Next
Click Next
Continue to page 15

13 D-Link DI-704GU Quick Install Guide
Configuration
If your ISP uses L2TP (Layer
Two Tunneling Protocol),
select the corresponding radio
button.
If you have a Dynamic IP
connection, enter the L2TP
Server IP Address, User Name,
and Password provided to you
by your ISP.
If yo u have a Static I P
connection, enter the L2TP
IP Address, Subnet Mask,
Gateway IP Address, L2TP
Server IP, User Name, and
Password provided to you by
your ISP.
L2TP
Click Next
Click Next
Click Next
Continue to page 15

14D-Link DI-704GU Quick Install Guide
Configuration
Select this option if you connect
to the internet through Telstra
BigPond Cable Broadband in
Australia.
Enter the User Name, and
Password provided to you by
your ISP.
Big Pond
Click Next
Click Next
Continue to page 15

15 D-Link DI-704GU Quick Install Guide
Configuration
Click Restart
For additional settings or information, refer to the Advanced, Tools,
or Status tabs on the web-management interface; or to the User’s
Manual located on the CD.
You will be returned to the Home tab. Close this web browser window
and open a new one (i.e., Internet Explorer or Netscape®Navigator).
Link to your favorite Web site to test your Internet connection.
Your Setup is Complete!
Test Internet Connection

16D-Link DI-704GU Quick Install Guide
Printer Wizard
Make sure your printer is connected to the USB port on the router.
Printer Wizard
Click Run Printer Wizard
Click Next
Click Next
The wizard will identify the make
and model of your printer, as
well as its status.

17 D-Link DI-704GU Quick Install Guide
Printer Wizard
Click Next
Click Next to run the Printer
Setup application.
Click Run
This application can only run
when accessed from the router.
Do not click Save.
Click Run

18D-Link DI-704GU Quick Install Guide
Printer Wizard
You may need to supply the
drivers for your printer if they
are not built into Windows®.
Click Browse to locate the
driver and then click OK.
Once the wizard has completed installing your printer, you will be
prompted to print a test page to verify its functionality.
Click Finish
Click OK
Click OK

19 D-Link DI-704GU Quick Install Guide
Appendix
Appendix
To connect to the network, make sure
the network adapter in your computer
is configured properly. Here’s how to
configure the network adapter to obtain
an IP address automatically when using
the DI-704GU Gigabit QoS Router.
For Microsoft Windows®XP:
Right click on My Network Places
and select Properties. Right click
on the Network Connection
associated with the Ethernet adapter
and select Properties (e.g., D-Link
DFE-530TX+).
Click OK
Click OK
Select Obtain an IP Address
automatically.
Click Internet Protocol (TCP/IP)
and then click Properties.

20D-Link DI-704GU Quick Install Guide
Appendix
For Apple Macintosh®OS X:
Go to the Apple Menu and click on
System Preferences, and select
Network.
The IP address information,
the Subnet Mask, the Router’s
IP address, and the Ethernet
adapter address will appear.
Click Network
Select Built-in Ethernet in
the Show pull down menu.
Select Using DHCP in the
Configure pull down menu.
Click Apply Now and restart
your computer (if necessary).