D-Link DIR-825/ACF User manual

Quick Installation Guide
DIR-825/ACF
Wireless AC1200 Dual Band Gigabit Router wit
Fiber WAN Port, 3G/LTE Support and USB Port

DIR-825/ACF Quick Installation Guide
BEFORE YOU BEGI
Delivery Package
•Router DIR-825/ACF
•Power adapter DC 12V/1.5A
•Ethernet cable CAT 5E)
•“Quick Installation Guide” brochure).
If any of the items are missing, please contact your reseller.
The “User Manual” and “Quick Installation Guide” documents are available
on D-Link website see www.dlink.ru).
!Using a power supply with a different voltage rating than the one
included will cause damage and void the warranty for this product.
2

DIR-825/ACF Quick Installation Guide
Default Settings
IP address of wireless router 192.168.0.1
Username (login) admin
Password admin
ame of wireless network (SSID)
2.4GHz DIR-825ACF
5GHz DIR-825ACF-5G
etwork key (PSK)
see WPS PIN on the
barcode label on the
bottom panel of the
device
!
For security reasons, DIR-825/ACF with default settings cannot
connect to the Internet. To get started, please set your own password
used to access the web-based interface and, if needed, configure other
settings recommended by your ISP.
3

DIR-825/ACF Quick Installation Guide
System Requirements and Equipment
•A computer with any operating system that supports a web browser.
•A web browser to access the web-based interface of the router:
◦Apple Safari 5 and later
◦Google Chrome 10 and later
◦Microsoft Internet Explorer 9 and later
◦Microsoft Edge 20.10240 and later
◦Mozilla Firefox 10 and later
◦Opera 10 and later.
•A NIC Ethernet or Wi-Fi adapter) to connect to the router.
•An 802.11a, b, g, n, or ac Wi-Fi adapter to create a wireless network.
•SFP transceiver to connect to a fiber optic line.
•A USB modem when it is necessary to connect to the Internet via mobile
operators' networks)1.
!
Your USB modem should be equipped with an active identification
card SIM or R-UIM) of your operator.
Some operators require subscribers to activate their USB modems prior
to using them. Please, refer to connection guidelines provided by your
operator when concluding the agreement or placed on its website.
For LTE and CDMA USB modems, it is required to disable the PIN
code check on the identification card prior to connecting the USB
modem to the router.
1 Contact your operator to get information on the service coverage and fees.
4

DIR-825/ACF Quick Installation Guide
Supported USB Modems
GSM modems
•Alcatel X500
•D-Link DWM-152C1
•D-Link DWM-156A6
•D-Link DWM-156A7
•D-Link DWM-156C1
•D-Link DWM-157B1
•D-Link DWM-157B1 Velcom)
•D-Link DWM-158D1
•D-Link DWR-710
•Huawei E150
•Huawei E1550
•Huawei E156G
•Huawei E160G
•Huawei E169G
•Huawei E171
•Huawei E173 Megafon)
•Huawei E220
•Huawei E352 Megafon)
•Prolink PHS600
•ZTE MF112
•ZTE MF192
•ZTE MF626
•ZTE MF627
•ZTE MF652
•ZTE MF667
•ZTE MF668
•ZTE MF752
5

DIR-825/ACF Quick Installation Guide
CDMA modems2
•Airplus MCD-650
•Airplus MCD-800
•AnyDATA ADU-300A
•AnyDATA ADU-500A
•AnyDATA ADU-510A
•Huawei EC306
•ZTE AC5710
•ZTE AC5730
L E modems
•Huawei E3131
•Huawei E3272
•Huawei E3351
•Huawei E3372
•Huawei E367
•Huawei E392
•Megafon M100-1
•Megafon M100-2
•Megafon M100-3
•Megafon M100-4
•Megafon M150-1
•Megafon M150-2
•MTS 824F
•MTS 827F
•Quanta 1K6E Beeline 1K6E)
•Yota LU-150
•Yota WLTUBA-107
•ZTE MF823
•ZTE MF827
Smartphones in USB tethering mode
•Some models of Android smartphones
!The manufacturer does not guarantee proper operation of the router
with every modification of the firmware of USB modems.
2 Performance of CDMA USB modems is not tested for the current firmware version.
6

DIR-825/ACF Quick Installation Guide
CO ECTI G TO PC
PC wit Et ernet Adapter
1. Make sure that your PC is powered off.
2. Connect an Ethernet cable between any of LAN ports located on the back
panel of the router and the Ethernet port of your PC.
3. To connect via USB modem: connect your USB modem to the USB port3
located on the back panel of the router.
!If you need to connect or change a USB modem to another one when
the router is powered on, power off the router, connect the modem to
the USB port, and power on the router.
4. To connect the device to a fiber optic line: connect your SFP transceiver
to the SFP port, then connect the fiber optic cable to the SFP transceiver.
5. To connect the device to an Ethernet line: in the web-based interface of
the router, select the router's LAN port that will be used as the WAN port
and create an Ethernet WAN connection. Then connect an Ethernet cable
between an available Ethernet port of the router and the Ethernet line.
!Please connect the router to the ISP's Ethernet line only after setting the
WAN port and creating the Internet connection.
6. Connect the power cord to the power connector port on the back panel of
the router, then plug the power adapter into an electrical outlet or power
strip.
7. Turn on the router by pressing the ON/OFF button on its back panel.
8. Turn on your PC and wait until your operating system is completely
loaded.
Now you should configure your PC to obtain an IP address automatically as
DHCP client).
3 It is recommended to use a USB extension cable to connect a USB modem to the
router.
7

DIR-825/ACF Quick Installation Guide
Obtaining IP Address Automatically
in OS Windows XP
1. Click the Start button and proceed to the Control Panel > etwork
and Internet Connections > etwork Connections window.
2. In the etwork Connections window, right-click the relevant Local
Area Connection icon and select the Properties line in the menu
displayed.
3. In the Local Area Connection Properties window, on the General
tab, select the Internet Protocol (TCP/IP) line. Click the Properties
button.
8

DIR-825/ACF Quick Installation Guide
4. Select the Obtain an IP address automatically and Obtain D S
server address automatically radio buttons. Click the OK button.
5. Click the ОК button in the connection properties window.
Now your computer is configured to obtain an IP address automatically.
9

DIR-825/ACF Quick Installation Guide
Obtaining IP Address Automatically
in OS Windows 7
1. Click the Start button and proceed to the Control Panel window.
2. Select the etwork and Sharing Center section. If the Control Panel
has the category view the Category value is selected from the View by
drop-down list in the top right corner of the window), choose the View
network status and tasks line under the etwork and Internet
section.)
3. In the menu located on the left part of the window, select the Change
adapter settings line.
4. In the opened window, right-click the relevant Local Area Connection
icon and select the Properties line in the menu displayed.
5. In the Local Area Connection Properties window, on the
etworking tab, select the Internet Protocol Version 4 (TCP/IPv4)
line. Click the Properties button.
10