D-Link VoIP Wireless Router DVG-G5402SP User manual

Quick Installation Guide
DVG-G5402SP
VoIP Router
Check Your Package Contents
DVG-G5402SP
VoIP Router
CD-ROM
which
includes
the User
Manual
Phone Cord
X 2
Ether (CAT5
UTP) Cable
12VDC, 1A
Power Adapter
Using a
power
adapter with
a different
voltage rating
will damage
this product
and void the
warranty.

2
Front Panel
Power：Solid indicates a connection to a
good power source.
Prov./Alm：A blinking light indicates the
DVG-G5402SP can not register with SIP
Server or can not get the IP address. A
blinking light also indicates the DVG-
G5402SP is attempting to connect with the
Provisioning server. Once the service
connects, the LED will turn off. The LED will
light solid red if the self-test or boot-up fails.
Register：The Register LED will turn on and
continously working when DVG-G5402SP is
connected to a VoIP service provider. The
LED will flash if not connected to a service
provider.
WAN：When a connection is established the
LED will light up solid. The LED will blink to
indicate activity. If the LED does not light up
when a cable is connected, verify the cable
connections and make sure your devices are
powered on.
WLAN：A steady light indicates a wireless connection. A blinking light
indicates that DVG-G5402SP is receiving / transmitting from/to the
wireless network
LAN：When a connection is established the LED will light up solid on the
appropriate port. The LEDs will blink to indicate activity. If the LED does
not light up when a cable is connected, verify the cable connections and
make sure your devices are powered on.
Phone：This LED displays the VoIP status and Hook activity on the
phone port that is used to connect your normal telephone(s). If a phone
connected to a phone port is off hook or in use, this LED will light solid.
When a phone is ringing, the indicator will blink.
Line：Light on means the line is in use (off-hook).
Hardware Overview

3
Rear Panel
1. Antenna: Connect to a
wireless network.
2. Line: Connect to your original
telephone line on the wall jack
with RJ-11 cable.
3. Phone Port (1-2): Connect to
your phones using standard
phone cabling (RJ-11).
4. LAN: Connect to your
Ethernet enabled computers
using Ethernet cabling.
5. WAN: Connect to your
broadband modem using an
Ethernet cable.
6. Power Receptor: Receptor for
the provided power adapter.
7. Ground: A conducting
connection with the earth.
Connect with the ground so as
to make the earth a part of an
electrical circuit using metal
wire.
Hardware Overview
()

4
A. Insert one end of the Ethernet cable into the Ethernet (LAN) port on
the back panel of the DVG-G5402SP and the other end of the cable
to an Ethernet Adapter or available Ethernet port on your computer.
B. Insert one end of the Ethernet cable into the WAN port on the back of
the DVG-G5402SP and the other into your cable/DSL modem or the
LAN port of your router.
C. Insert a telephone cable into the Phone port, and then connect the
cable to your telephone.
Installing the Hardware

5
D. Insert your original telephone line on the wall jack (PSTN) into the
Line port.
E. Connect the power adapter to the power input at the back panel of
the DVG-G5402SP and then plug the other end of the power adapter
to a wall outlet or power strip. On the front of the device, the Power
LED will turn On to indicate proper operation.
F. Check the LED display on the front of the VoIP Wireless Router to
confirm that the connections have been made.
Installing the Hardware (continued)

6
After the installations are completed, your network should look similar to
the diagram below.
Hardware configuration is complete! If your VoIP service is already activated, you
can make phone calls now.
Installing the Hardware (continued)

7
Configuration
To access the web-based configuration utility, open a web browser such
as Internet Explorer and enter the IP address of the DVG-G5402SP.
Open your Web browser and
type http://192.168.8.254 into
the URL address box. Press
the Enter or Return Key.
Click Login to enter Web Site.
Click Setup Wizard.

8
Configuration (continued)
The username of ADMIN and USER
have been defined and locked by
default. It is highly recommended to
create a login password to keep
your router secure.
Enter a NTP server or use the
default server.
Click Next.
Click Next.
Click Next.

9
Configuration (continued)
Select your Internet connection type:
DHCP – Most Cable ISPs or if you
are connecting the DVG-G5402SP
behind a router.
Static IP – Select if your ISP
supplied you with your IP settings.
PPPoE – Most DSL ISPs.
PPTP – Select if required by you
r
ISP.
Select Manual to manually enter IP
address of DNS or select Auto i
f
DNS is assigned by ISP.
Register to the SIP Proxy Serve
r
by clicking Enable support of SIP
Proxy Server. Enter Proxy
Server IP/Domain and Port.
The Outbound Proxy Support is
optional. To register, please clic
k
on the Outbound Proxy Support
check box and enter Outbound
Proxy IP/Domain and Port in it.
Registration by phone line: enter
Number, User ID/Account and
Password supplied by your ITSP.
Click on the Register check box to
register to Proxy Server.
Click Next.
Click Next.

10
Configuration (continued)
Setup is finished. Check the
summary of your settings. To
make new settings effective, you
must click on the Restart button
to reboot the DVG-G5402SP.
Click Restart.
Click on the Enable wi
r
eless LAN
interface check box to build a
wireless network. Enter the SSID to
name your wireless network. All
devices must have the same SSID
to communicate on the wireless
network. Select a wireless channel.
Select the 802.11 Mode of your
network which can work in different
speed of wireless connection.
Click Next.
Select your wireless security modes:
None, WEP, WPA-PSK, or WPA for
your wireless network.
Click Next