D-Link SECURICAM DCS-910 User manual

2D-Link DCS-910/920 Quick Install Guide
System Requirements
• Computer with Windows®Vista or XP SP2
• PC with 1.3GHz or above; at least 128MB RAM
• Internet Explorer 6.0 or Netscape Navigator™7.0 and above
• Existing 10/100 Ethernet-based network or 802.11b/g wireless
network
CAT5 Ethernet Cable
Package Contents
DCS-910/920
Internet Camera
System Requirements
If any of the above items are missing, please contact your reseller.
Manual and
Software on CD
Camera Stand
5V 2.5A AC Power Adapter
Antenna (DCS-920 only)
Note: Using a power supply with a different voltage will cause damage and
void the warranty for this product.

3 D-Link DCS-910/920 Quick Install Guide
Hardware Overview
Hardware Overview
Front
Wireless Antenna*
Camera Stand
Power and Link LED
Camera Lens
* Antenna available on the DCS-920 only

4D-Link DCS-910/920 Quick Install Guide
Hardware Overview
Rear
Camera Stand
Power Connector
Reset
Ethernet Connector
Wireless Antenna*
* Antenna available on the DCS-920 only

5 D-Link DCS-910/920 Quick Install Guide
Hardware Installation
Hardware Installation
Note: It is required that an Ethernet cable is used during initial
setup. Once your wireless configuration is set, you may disconnect
the Ethernet cable and begin communicating wirelessly with your
DCS-920.
Attach the Swivel Stand
Locate the stand mount on the back
panel of the DCS-910/920 and screw on
the swivel stand to the DCS-910/920.
Attach the Antenna
Locate the antenna included with your
DCS-920 and attach it to the antenna
connector located on the back of the
DCS-920.
Note: Wireless Antenna is provided
with the DCS-920 only.
Connect the Ethernet Cable
Connect the included Ethernet cable to
the network cable connector located on
the bottom panel of the DCS-910/920
and attach it to the network. Network
Connectivity is confirmed when the
green LED Indicator on the camera is
illuminated.

6D-Link DCS-910/920 Quick Install Guide
Hardware Installation
Attach the External Power Supply
Attach the external power supply to the
DC power input connector located on the
bottom panel of the DCS-910/920 and
connect it to your local power supply.
Note: Power source is confirmed
when the red LED Power Indicator
located below the lens on the camera
is illuminated.

7 D-Link DCS-910/920 Quick Install Guide
Software Installation
Click Next
Insert the DCS-910/920 CD into the CD-ROM drive. If the CD Autorun
function does not automatically start on your computer, click Windows®
Start > Run. In the Run command box type “D:\DCS910920.exe”,
where D: represents the drive letter of your CD-ROM. If it does start,
proceed to the next screen.
Software Installation
Click Setup Wizard
Click Next to continue.
Click Yes
Click Yes to accept the License
Agreement.

8D-Link DCS-910/920 Quick Install Guide
Software Installation
Click Next
Click Finish
Click Finish to complete the
installation.
To start the installation click
Next.
Note: The installation may take
several minutes to complete.

9 D-Link DCS-910/920 Quick Install Guide
Configuration
Configuring Your Camera with
the Installation Wizard
Click on the D-Link Setup Wizard SE icon that was created in your
Windows Start menu.
The Setup Wizard will appear and show the MAC address of the
DCS-910/920 and an IP Address (which may or may not be correct
depending on what you have your DCS-910/920 connected to). If
you have a DHCP server on your network, there will be a valid IP
Address displayed here.
Note: A DHCP server is a device that supplies IP addresses to your
network devices automatically.
Click the Wizard button
Your camera’s IP Address will
be displayed here along with its
corresponding MAC Address.

10D-Link DCS-910/920 Quick Install Guide
Configuration
Click Next
Enter the admin ID and password.
Note: The default Admin ID is admin
with the password left blank.
Select DHCP if you want to obtain
a new IP address every time the
camera boots up, or select static IP
to use the same IP address at each
boot up.
Click Next
Click Next
Enable wireless settings and enter
your wireless network information.
Select your wireless security settings,
and click Next.
Note: Wireless is available only for
the DCS-920.