D-Link DCS-6314 User manual

This document will guide you through the basic
installation process for your new D-Link Network
Camera.
DCS-6314
Version 1.0
April 25, 2013
Quick Install Guide
Full HD Outdoor Fixed Dome Network Camera

DCS-6314 Quick Install Guide
This installation guide provides basic instructions for installing the DCS-6314 Network Camera on
your network. For additional information about how to use the camera, please see the User Manual
which is available on the CD included in this package or from the D-Link support website.
Installation Steps
1. Verify Package Contents
2. Hardware Overview
3. microSD Card Installation
4. Mounting Instructions
5. Setup Wizard
6. Adjusting the Lens 3-axis Gimbal
1. Package Contents
DCS-6314 Network Camera
Manual and Software on CD-ROM
Power Adapter
Security Wrench
CAT5 Ethernet Cable
Screws and wall socket
Weather Shield
4-pin Terminal Block
Quick Install Guide
If any of the above items are missing, please contact your reseller.
Safety Notice:
Installation and servicing should be done by certied technicians so as to conform to all local
codes and prevent voiding your warranty.

D-Link DCS-6314 Quick Install Guide
3
ENGLISH
2. Hardware Overview
Install the microSD Card
Push the microSD card into the camera with the gold contacts
oriented towards the base of the camera. To eject, push the
microSD card into the slot.
3. microSD Card Installation
Disassemble the Camera
Open the camera enclosure by loosening the
three screws. Lift the dome o the base of the
camera.
Power Connector
Connects to 12V DC power
Ethernet Jack
RJ-45 connector for Ethernet
which can also be used to power
the camera using Power over
Ethernet (PoE)
Reset Button
Resets camera to factory
default settings
Audio In
Connects to a microphone
DI/DO Wiring, 12V DC output
I/O connectors for external devices
Audio Out
Connects to speakers

D-Link DCS-6314 Quick Install Guide
4
ENGLISH
4. Standard Mounting Instructions
Mounting Installation
Please refer to the User Manual for detailed instructions regarding installation and mounting of
the camera using a mounting bracket.
Style 1 - Concealed Cable Installation
Height: 25.6mm (1.0 inches)
Diameter: 122mm (4.8 inches)
Weight: 135g (0.3lbs)
Figure 2.2Figure 2.1
Weather Shield
Weather Shield
Screw

D-Link DCS-6314 Quick Install Guide 5
ENGLISH
Style 2 - Exposed Cable Installation
Height: 25.6mm (1.0 inches)
Diameter: 122mm (4.8 inches)
Weight: 135g (0.3lbs)
Figure 2.3 Figure 2.4
Figure 2.5

D-Link DCS-6314 Quick Install Guide
6
ENGLISH
Pendant Mount (DCS-34-2)
Height: 201mm (7.9 inches)
Diameter: 150mm (5.9 inches)
Weight: 665g (1.45lbs)
Figure 3.4
Pendant
Bracket
Bracket Cap
Rubber
Seal
Figure 3.2
Figure 3.3
Figure 3.1
Bracket
Cap
Mounting
Plate

D-Link DCS-6314 Quick Install Guide 7
ENGLISH
Wall Mount (DCS-34-3)
Height: 253mm (9.96 inches)
Diameter: 150mm (5.9 inches)
Weight: 770g (1.7lbs)
Bracket Cap
Wall
Mount
Figure 4.2
Figure 4.4Figure 4.3
Figure 4.1
Bracket
Cap
Mounting
Plate
Dome
Camera
Wall
Mount

D-Link DCS-6314 Quick Install Guide
8
ENGLISH
Connection with a PoE Switch
If you are using a PoE switch, connect the IP camera to the switch via an Ethernet cable, which
will provide transmission of both power and data over a single cable.
General Connection Using 12V DC Power Adapter
1. Connect the network camera to a switch or router via an Ethernet cable.
2. Connect the supplied power cable from the camera to a power outlet.

D-Link DCS-6314 Quick Install Guide 9
ENGLISH
5. Setup Wizard
Click Setup Wizard to begin the installation.
Insert the DCS-6314 CD into your computer's CD-ROM drive to begin the installation. If the Autorun
function on your computer is disabled, or if the D-Link Launcher fails to start automatically, click
Start > Run. Type D:\autorun.exe, where D: represents the drive letter of your CD-ROM drive.
The following window will open. Click Next to continue.
Click Yes to accept the License Agreement.
Click Finish to complete the installation.
Select the location to install. Click Next to start the
installation process.
Note: The installation may take several minutes to nish.

D-Link DCS-6314 Quick Install Guide
10
ENGLISH
Click on the D-Link Setup Wizard SE icon that was created
in your Windows Start menu.
Start > D-Link > Setup Wizard SE
Take a moment to conrm your settings and click Restart.
Select DHCP if your camera obtains an IP address automatically
when it boots up. Select Static IP if you want to manually enter
the camera's network settings.
Click Next to proceed to the next page.
Enter the Admin ID and password. When logging in for the rst
time, the default Admin ID is admin with the password left
blank.
Click Next to proceed to the next page.
The Setup Wizard will appear and display the MAC address and IP address of your camera(s). If
you have a DHCP server on your network, a valid IP Address will be displayed. If your network
does not use a DHCP server, the network camera's default static IP 192.168.0.20 will be
displayed.
Click the Wizard button to continue.