D-Link DCS-5222L User manual

DCS-5222L
Quick Install Guide
HD Pan & Tilt Day/Night Network Camera

If any of the above items are missing, please contact your reseller.
DCS-5222L HD Pan & Tilt Day/Night Network Camera
Power Adapter
Package Contents
Mounting Kit
CAT5 Ethernet Cable
Audio In/Out Cable
Minimum Requirements
Mobile Device (to use mydlink Lite app)
• iPhone, iPad, or Android smartphone or tablet
(Refer to the mobile app’s store page to see if your device is compatible)
Network Device and Service
• A wireless router (802.11ac/n/g) with Internet service
• An e-mail account (required to create a mydlink® account)
* If you use a mobile device with the mydlink Lite app, a PC is not required for
setup. Refer to Setting up Your Camera on page 4.
2
ENGLISH

Product Overview
Camera Lens
Microphone
Light Sensor
Power LED
PIR Sensor
WPS Status LED
Power Connector
Ethernet Port
Reset Button
WPS Button
Front
Back
IR LEDs
Speaker
I/O Connector
Audio In/Out
Antenna
microSD Card
Slot
Focus Ring
3
ENGLISH

Setting Up Your Camera
System Requirements: Refer to the mydlink Lite app page on Apple App Store, Google Play or Windows Phone Store.
Launch the mydlink Lite app, then create a new account or log in to your
existing account.
Download the free mydlink Lite app on your smartphone or tablet by
scanning the QR code below, or by searching for mydlink Lite in the app
store for your device.
1
2
3The app will guide you through the rest of the conguration process.
4
ENGLISH

Mount the Camera
Please refer to the steps below to assist you with mounting the camera.
We suggest that you congure the camera before mounting.
1. Place the arm mount where you want to position
the camera and use a pencil to mark the holes.
Make sure you allow adequate space for the
necessary cables to be routed. The camera can
be mounted to either side of the camera shoe.
2. Depending on the material of the wall or ceiling,
use a 6mm drill bit to drill two holes where you
marked. If the wall is made out of concrete, after
drilling the holes, insert the plastic anchors, and
then insert the screws.
3. The power and Ethernet cables can be concealed
behind the mounting bracket.When you run the
cables through the channel, secure them with
the built-in guides. Leave enough cable length
protruding from the top to connect the cables to
the camera.
4. Fasten the arm mount to the wall using the
screws provided. Lightly pull on the arm mount
to make sure it is fastened securely.
5. Align the camera base mounting guides with
the camera shoe and thumbscrew on the arm
mount. Tighten the thumbscrew to lock the
camera in place.
Do not overtighten the screws as this may crack the bracket.
5
ENGLISH

1. What is a mydlink No.? What is it used for?
Each camera has a unique eight-digit mydlink No. which will be shown on
the label on the back of your camera. This eight-digit number identies
your device, and is required to add your device to your mydlink account.
2. What can I do if my DCS-5222L is not working correctly?
• Reset the camera (see next step) and run the setup steps starting
on page 4 again.
• To make sure your hardware is installed correctly, make sure that:
- the power LED is solid green
- your Internet connection is working
- your router’s LAN & WAN connections are working
- your router supports UPnP®
- your camera is on the same network as your mobile device
- both your mobile device and camera have a working Internet connection
• If your camera is still not working, check your router and make sure it
has the latest rmware.
3. What can I do if I forget my password?
FAQs
If you forget your password, you must reset the
camera. Unfortunately, this process will change
your settings back to factory default. To reset the
camera, locate the reset button on the back of
the camera. With the camera powered on, use an
unfolded paper clip to hold the button down for
10 seconds. Run the setup procedure located on
page 4 once the camera restarts.
4. Why is there a white haze when viewing in night vision mode?
When viewing in night vision mode, the IR lights on the camera may be
reecting o a nearby surface. Try repositioning the camera in order to
avoid glare from IR LEDs.
Reset
Button
6
ENGLISH

Notes
7
ENGLISH

Technical Support
This guide is for initial conguration. Please refer to the user manual
to learn more or visit http://www.mydlink.com for more information.
Also feel free to contact us. U.S. and Canadian customers can contact
D-Link Technical Support through our website.
http://support.dlink.com
USA
http://support.dlink.ca
Canada
Version 2.2
March 24, 2015
Copyright ©2015 All rights reserved. D-Link and the D-Link logo are registered trademarks of D-Link
Corporation or its subsidiaries. Other trademarks are the property of their respective owners. Maximum
wireless signal rate derived from IEEE Standard 802.11g and 802.11n specications. Actual data throughput
will vary. Network conditions and environmental factors, including volume of network trac, building
materials and construction, and network overhead, lower actual data throughput rate. Environmental
factors will adversely aect wireless signal range. Product specications, size and shape are subject to
change without notice, and actual product appearance may dier from that depicted on the packaging.
Visit dlink.com (US) or dlink.ca (Canada) for more details.