D-Link nuclias connect DAP-2662 User manual

This document will guide you through the basic
installation process for your new access point.
Building Networks for People
DAP-2662
Documentation also available
via the D-Link Website
Quick Installation Guide
Wireless AC1200 Wave 2 Dual-Band PoE Access Point

2
Before You Begin
This installation guide provides instructions
for installing the DAP-2662 on your network.
Additional documentation is also available on
the D-Link support website.
• D-Link Nuclias Connect User Manual: For
additional information and instructions
on how to configure the device using
D-Link Nuclias Connect.
• DAP-2662 User Manual: For additional
information and instructions on how to
congure the device using the web user
interface.
Package Contents
This DAP-2662 package should include the
following items:
• 1 x DAP-2662
• 1 x Quick Install Card
• 1 x Mounting bracket
• 2 x Ceiling brackets
• 4 x Rubber stands
• 4 x Screws
• (Optional) 1 x Power supply
If any of the above items are damaged or
missing, please contact your local D-Link reseller.
System Requirements
• A PC or laptop with a working Ethernet
adapter or wireless interface.
• Mozilla Firefox 52.0 or higher, Internet
Explorer 11 or higher, Safari 10.1 or higher,
Google Chrome 59 or higher.
• OS X 10.8.5, Windows 7, Linux (Ubuntu 12)
and higher.
Hardware Overview
LED Indicators
Figure 1: Front Panel LED
# LED Status Description
1
Power/
Status
LED
Solid
green
Indicates that the
access point is
working correctly.
Solid
red
Indicates that the
access point has
malfunctioned.
Table 1: LED Description
Interface Connectors
Figure 2: Bottom Connectors
1
23
1

3
# Connector Description
1 Reset Button
Press and hold for 10
seconds to factory
reset the device.
2 PoE LAN Port Gigabit RJ-45
port for data.
3Power
Receptor
To connect the
supplied power
adaptor.
Table 2: Interface Description
Powering the Access Point
Using Power over Ethernet (PoE)
Use a standard Ethernet cable to connect the
LAN port on the DAP-2662 to a PoE power source
device such as a PoE switch or PoE injector.
(Optional) Using the power adapter
1. Connect the power connector of the
adapter to the power input on the
DAP-2662 and plug the adapter into a
nearby power outlet.
Conguring the Access Point
Note: D-Link recommends conguring the
device before mounting it.
Using D-Link Nuclias Connect
The DAP-2662 is designed to be managed
through D-Link Nuclias Connect. Refer to the
D-Link Nuclias Connect Manual for detailed
conguration instructions.
Figure 4: Connecting through D-Link Nuclias
1. Download the free Nuclias Connect
app from the App Store or Google Play
by searching for Nuclias Connect or by
scanning the QR code below.
2. Open the Nuclias Connect app and follow
the onscreen instructions to discover and
set up your device.
Manual Conguration
If you are not using Nuclias Connect, you may
manually congure the DAP-2662 using its web
user interface (UI). Refer to the DAP-2662 User
Manual for detailed conguration instructions.
Use the following methods to access the web
user interface:
Note: The management computer must be in
the same subnet as the DAP-2662.
1. Use an Ethernet cable to connect the
management computer to the PoE switch
or to the PoE Injector the DAP-2662 is
connected to.
2. Open a web browser on the management
computer and type in dap.2662.local in
the address eld and press Enter.
3. When prompted, enter the default login
credentials:
User name: admin
Password: admin
PoE Switch or Router
Nuclias Connect
Software
DAP-2662

4
Mounting the Access Point
The DAP-2662 can be mounted on a wall or
ceiling for optimal coverage.
Mounting on a Solid Wall or Ceiling
1. Use the mounting plate to mark the
location where to drill the holes in the
wall or ceiling.
Figure 5: Mark Location
2. Drill holes on the markings and place the
included anchors into the drilled holes.
Figure 6: Drill Holes
3. Align and place the mounting plate on
top of the anchors and use the included
screws to secure the mounting plate to
the surface.
Figure 7: Attaching the Mounting Plate
4. Connect the Ethernet cable and power
adapter (optional) to the device.
5. Attach the DAP-2662 to the mounting
plate by snapping the device into place
onto the plate and rotating clockwise until
the device locks into place.
6. Use the Allen key and screw to lock it in
at the top.
Mounting on a Ceiling Crossbar
1. Clip the two included ceiling brackets onto
a ceiling crossbar. Make sure both brackets
are positioned in line with each other.
Figure 8: Attaching the Ceiling Brackets

5
2. Use the included screws to secure the
mounting plate to the ceiling brackets.
Figure 9: Attaching the Mounting Plate
3. Connect the Ethernet cable and power
adapter (optional) to the device.
4. Attach the DAP-2662 to the mounting plate
by placing it onto the plate and rotating
clockwise until the device locks into place.
Reboot/Reset the Access
Point
If necessary, the DAP-2662 can be manually
rebooted or reset to factory default settings.
Rebooting the device
Unplug the Ethernet cable (if connected to PoE
power source device) or the power adaptor to
power o the device and replug it to power it
on again.
Resetting the device
Press and hold down the recessed reset
button at the bottom of the device for
6 to 15 seconds then release to reset the device
to its factory default settings.
Additional Information
For additional support, please refer to the
user manual, or visit your local D-Link support
website.

6
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
o and on, the user is encouraged to try to correct the interference by one of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Non-modications Statement:
Any changes or modications not expressly approved by the party responsible for compliance
could void the user’s authority to operate this equipment.
Caution:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This device and its antenna(s) must not be co-located or operating in conjunction with any other
antenna or transmitter except in accordance with FCC multi-transmitter product procedures. For
product available in the USA/Canada market, only channel 1~11 can be operated. Selection of
other channels is not possible.
Note
The country code selection is for non-USA models only and is not available to all USA models. Per
FCC regulations, all WiFi product marketed in the USA must be xed to USA operational channels
only.
RF Frequency Requirements
This device is for indoor use only when using all channels in the 5.15 to 5.25 GHz frequency range.
High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz
bands. These radar stations can cause interference with and/or damage this device. This device
will not operate on channels which overlap the 5600-5650 MHz band.
It is restricted to indoor environments only.
IMPORTANT NOTICE:
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20 cm
between the radiator and your body.

7
Innovation, Science and Economic Development Canada (ISED)
Statement:
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Innovation, Science and Economic Development Canada (ISED)
Statement:
This device complies with ISED licence-exempt RSS standard(s). Operation is subject to the
following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d’ISED applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the
potential for harmful interference to co-channel mobile satellite systems;
(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour
une utilisation à l’intérieur an de réduire les risques de brouillage préjudiciable aux systèmes de
satellites mobiles utilisant les mêmes canaux;
Operations in the 5.25-5.35 GHz band are restricted to indoor usage only.
Les opérations dans la bande de 5.25-5.35 GHz sont limités à un usage intérieur seulement.
Radiation Exposure Statement
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20 cm
between the radiator and your body.
Déclaration d’exposition aux radiations
Cet équipement est conforme aux limites d’exposition aux rayonnements ISED établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de
20 cm de distance entre la source de rayonnement et votre corps.
Japan Voluntary Control Council for Interference Statement
この装置は、クラス B情報技術装置です。この装置は、家庭環境で使用することを目的と
していますが、この装置がラジオやテレビジョン受信機に近接して使用されると、受信障
害を引き起こすことがあります。
取扱説明書に従って正しい取り扱いをして下さい。 VCCI-B
Japan Voluntary Control Council for Interference Statement
This is a Class B product based on the standard of the VCCI Council. If this is used near a radio or
television receiver in a domestic environment, it may cause radio interference. Install and use the
equipment according to the instruction manual.
電波法により5GHz帯は屋内使用に限ります。

Ver. 1.01(WW)_130x183
2019/10/04
5300-7597-01W
Product and Warranty Information
To nd out more about D-Link products or marketing information, please visit the website http://
www.dlink.com.
The D-Link Limited Lifetime Warranty information is available at
http://warranty.dlink.com/
位置: 中文使用說明書
電池使用安全說明
低功率警語 :
• 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自
變更頻率、加大功率或變更原設計之特性及功能。
• 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象
時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法
規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用
電波輻射性電機設備之干擾。
• 使用此產品時應避免影響附近雷達系統之操作