SUGGESTED SPECIFICATIONS: projection screen(s),
(H) x (W). Tensioned Conference Electrol® screen shall
have three motors, one to operate door, one to operate screen and one to
operate document camera arm. Door motor electrically operated 120 volt (60
Hz) not more than 1.2 amp. Shall have motor mounted inside the roller, to be
three wire with ground, quick reversal type, oiled for life, with automatic ther-
mal overload cutout, integral gears, capacitor and an electric brake to prevent
coasting. To have pre-set but adjustable limit switches to automatically stop
fabric door in the “ down“ position. The door will lift to the closed position
where an internal micro-switch will cut of the electrical current to the door
motor. The roller to be of rigid aluminum. Screen motor is electrically operated
120 volt (60 Hz) not more than 2.4 amp. Shall have motor mounted inside the
roller, to be three wire with ground quick reversal type, oiled for life, with auto-
matic thermal overload cutout, integral gears, capacitor and an electric brake
to prevent coasting. To have pre-set but adjustable limit switches to automati-
cally stop picture surface in the ”up“ and ”down“ positions. The roller to be of
rigid metal. Camera arm motor is electrically operated 120 volt (60 Hz) not
more than 2.4 amp. Shall have motor mounted inside the roller, to be two wire
with ground quick reversal type, oiled for life, with automatic thermal overload
cutout, integral gears, capacitor and an electric brake to prevent coasting. To
have pre-set but adjustable limit switches to automatically stop the camera
arm in the ”up“ and ”down“ positions. Screen fabric to be seamless, lame retar-
dant and mildew resistant vinyl, with black masking borders standard. Each
side of the fabric to have tab guide cable system to maintain even lateral ten-
sion and hold surface lat. Custom slat bar with added weight maintains
vertical tension on the screen surface. The ends of the slat to be protected by
heavy duty plastic caps enclosing a preset adjustable mechanism for screen
tensioning. Case shall be constructed of ¾” medium density iberboard.
Bottom of case to be self-trimming with a built-in lange around the bottom of
the case. A section of the bottom of the case shall be an aluminum door
equipped with hinges so that it opens and closes automatically with the lower-
ing and raising of the picture surface. The balance of the bottom of the case
shall be a second hinged aluminum door with manual opening to provide
access. Hinges shall be mounted in a concealed way. Junction box shall be
internally integrated into the housing making it possible to install the housing
and wire to the building’s electrical system during construction. The junction
box shall contain a quick connect connector that is mounted in the housing
for easy plug-in connection to the motorized fabric and roller assembly. The
motorized fabric and roller assembly to be installed in the case at the factory
or at a later time at the job site. To be complete with integrated low voltage
control unit and three position control switch and cover plate.
SPECIFICATION DATA
HDTV (16:9) Format Dimensions
Viewing Area (H x W) Nominal Diagonal Maximum Drop* Overall Length of Case Weight. Approx. Ship. Wt.
In. Cm In. Cm In. Cm In. Cm Lbs. Kg Lbs. Kg
45" x 80" 114 x 203 92" 234 19" 48 120" 305 ]325 147.4 569 258.1
52" x 92" 132 x 234 106" 269 12" 30 120" 305 340 154.2 584 264.9
54" x 96" 137 x 244 110" 279 25½" 65 143⅛" 364 378 171.5 662 300.3
58" x 104" 147 x 264 119" 302 21½" 55 143⅛" 364 383 173.7 667 302.5
65" x 116" 165 x 295 133" 338 14½" 37 143⅛" 364 396 179.6 680 308.4
Wide (16:10) Format Dimensions
Viewing Area (H x W) Nominal Diagonal Maximum Drop* Overall Length of Case Weight. Approx. Ship. Wt.
In. Cm In. Cm In. Cm In. Cm Lbs. Kg Lbs. Kg
50" x 80" 127 x 203 94" 239 14" 36 120" 305 326 147.9 570 258.5
57½" x 92" 146 x 234 109" 277 22½" 57 143⅛" 364 378 171.5 662 300.3
60" x 96" 152 x 244 113" 287 19½" 50 143⅛" 364 381 172.8 665 301.6
65" x 104" 165 x 264 123" 312 14½" 37 143⅛" 364 384 174. 2 668 303.0
69" x 110" 175 x 279 130" 330 10½" 27 143⅛" 364 390 176.9 674 305.7
72½" x 116" 184 x 295 137" 348 7" 18 143⅛" 364 403 182.8 687 311.6
Tensioned Conference Electrol
®
Automatic Electric Projection Screen Model
PRODUCT NOTES
• All viewing surfaces will be seamless.
• All viewing surfaces are standard with black
backing.
• *All screens standard with 12" (30 cm) black drop at
top except the 69" x 110", which has 10½" (27 cm),
and the 72½" x 116", which has 7" (18 cm).
• Custom formats and sizes available upon request.
Contact Da-Lite for feasibility.
• Overall case length dimensions +/- ¼" (6 mm).
• Detail dimensional drawings, wiring diagrams and
installation instructions available upon request.
• Speciications subject to change without notice.
WHEN ORDERING, MARK APPROPRIATE SELECTIONS
1. Select size from charts below.
2. Select viewing surface (All Da-Lite surfaces are GREENGUARD GOLD Certiied.):
HD Progressive 0.6 High Contrast Da-Mat®
HD Progressive 0.9 Pearlescent
HD Progressive 1.1 Cinema Vision
Da-Mat® High Contrast Cinema Vision
3. Optional accessories:
Wireless Remote Control for LVC.
Radio Frequency Remote
Radio Frequency Range
Extender available
Infrared Remote
Key Locking Cover Plate for LVC Switch.
220/240 Volt (50 Hz) motor.
Video Projector Interface Control
– built-in
Plenum Enclosure – For use in
environmental air space.
