Daewoo DOC-091RH User manual

MODE L #: DOC -091R
DOC -091R H
R OOM AIR C ONDITIONE R
US E & C AR E MANUAL
P OR TAB L E T YP E R OOM AIR C ONDIT IONE R
P lease read carefully and thoroughly this manual before
operating the unit.
If you still have any difficulties or problems, consult your
dealer for help or E LE C TR ONIC S .
P leas e keep this manual well.
W1
R
CUS
LIS TE D
UL and
C UL listed

CONTENTS
1.SAFETY RULES.............................................................................
2.NAMES OF PARTS..........................................................................
3.ACCESSORIES................................................................................
4.OPERATION PANEL OF THE AIR CONDITIONER........................
5.OPERATING INSTRUCTION FOR THE AIR CONDITIONER ........
6.INSTALLATION...............................................................................
7.MAINTENANCE...............................................................................
8.TROUBLE SHOOTING....................................................................
1
2
2
3
4
6
7
8

SAFETY RULES
1. DO NOT CONNECT UNIT TO ANY AC SOCKET IN DISREPAIR OR WITH
CONNECTIONS.
2. DO NOT USE IN THE FOLLOWING LOCATIONS:
- NEXT TO SOURCE OF FIRE.
- AN AREA WHERE OIL IS LIKELY TO SPLASH.
- AN AREA EXPOSED TO DIRECT SUNLIGHT.
- AN AREA WHERE WATER IS LIKELY TO SPLASH.
- NEAR A BATH, A SHOWER OR A SWIMMING POOL
- IN THE GREEN HOUSE
3. NEVER INSERT YOUR FINGERS OR ANY FOREIGN OBJECTS INTO THE AIR
OUTLET. TAKE SPECIAL CARE TO WARNCHILDREN OF THESE DANGERS.
4. ALWAYS STORE THE UNIT UPRIGHT IN ORDER TO MAINTAIN THE COMPRE-
SSOR IN A PROPER CONDITION.
5. BE SURE TO UNPLUG THE UNIT BEFORE CLEANING.
6. THE HEATER MUST NOT BE LOCATED IMMEDIATELY BELOW A SOCKET
OUTLET.
7. IF THE APPLIANCE IS COVERED, THERE IS A RISK OF OVERHEAT.
8. IF THE SUPPLY TOOL OF THIS APPLIANCE IS DAMAGED, IT MUST BE
REPLACED BY A REPAIR SHOP APPOINTED BY THE MANUFACTURER,
BECAUSE SPECIAL PURPOSE TOOLS ARE REQUIRED.
NOTE: The air-conditioner can be connected only to a supply with system
impedance no more than 0.4582 ohm. In case necessary, please consult your
supply authority for system impedance information.
1

ACCESSORIES
PARTS :
PARTS NAME :
DUCT
ADAPTOR A (FOR PERMANENT DUCT
MOUNTING)
ADAPTOR B (FOR TEMPORARY DUCT
MOUNTING)
WALL PLUG
QUANTITY :
1
1
1
4
4
Check all the accessories are included in the package and please refer to the installation instructions
for their usage.
ALKALINE BATTERIES 2
1
1
REMOTE CONTROLLER
WATER PUMP DRAIN HOSE
SCREWS
2
NAMES OF PARTS
OPRATION PANEL
AIR OUTLET
REMOTE CONTROLLER
CASTER
REAR COVER FRONT COVER
AIR INLET
OUTDOOR
WATER PUMP
DRAIN HOSE
POWER CORD
AIR INLET INDOOR
AIR OUTLET
OUTDOOR
AIR INLET
OUTDOOR
CONTINUOUS
DRAIN HOSE
FRONT VIEW SIDE VIEW REAR VIEW
Fig.1
Fig.2

3
OPERATION PANEL OF THE AIR CONDITIONER(COOLING AND HEATING)
OPERATING PANEL
OPERATION PANEL OF THE AIR CONDITIONER(COOLING ONLY TYPE)
TEMP SETTING BUTTON
Select your desired room temperature
setting by pressing the button (up)
or button (down)
DIGITAL DISPLAY
INFRARED
SIGNAL RECEIVER
TIMER ON/OFF INDICATOR
TIMER ON/OFFBUTTON
Program the on/off timer function
COOL/DRY/FAN INDICATOR
Green lamp will light when the mode is selected
FAN SPEED INDICATOR
WATER FULL INDICATOR
Red lamp will blink when the tank is full
POWER INDICATOR
POWER BUTTON
Turn on/off the unit
MODES BUTTON
Select the operation mode
from COOL.DRY.FAN.
FAN SPEED BUTTON
Press the button to select
the fan speed from
HIGH.MED or LOW
OPERATING PANEL
TEMP SETTING BUTTON
Press your desired room temperature
setting by pressing the button (up)
or button (down)
DIGITAL DISPLAY
TIMER ON/OFF INDICATOR
TIMER ON/OFF BUTTON
Program the on/off timer function
COOL/DRY/FAN/HEAT INDICATIOR
Green lamp will light when the mode is selected
FAN SPEED INDICATOR
WATER FULL INDICATOR
Red lamp will blink when the tank is full
POWER INDICATOR
POWER BUTTON
Turn on/off the unit
MODES BUTTON
Select the operation mode
from COOL.DRY.FAN.HEAT
FAN SPEED BUTTON
Select the fan speed from
HIGH.MED or LOW
INFRARED
SIGNAL RECEIVER
Fig.4
Fig.3

Fig.5a
4
OPERATING INSTRUCTING FOR THE AIR CONDITIONER
Before Starting This Unit
1) Select a suitable location, make sure you have easy access to an electrical outlet.
2) Install the Flexible Exhaust Hose and the Adjustable Window Slider Kit as depicted in Fig.5 &
Fig.5a
Fig.5
NOTE: Step 2 is required only while using the cooling mode
3) Plug the unit into a 115V~60Hz grounded electrical outlet.
4) Make sure the water pump drain hose is correctly installed.
¡¡ 5) Press the on / off button to turn on the unit.
1 BEFORE USE
Dehumidifying and Cooling Operations
OOOO
- The operating range for cooling operating is 17 C-30 C/63 F-86 F.
- If the cooling or dehumidifying operations have been switched off and need switching on again
in a short time, allow approximately three minutes for the cooling or dehumidifying operations
to resume.
- Make sure the water pump drain hose is correctly connected to the unit.
Power supply:
- Insert the AC Power Plug to a AC socket.
- Do not connect the air conditioner to a multiple socket outlet which is also being used for other
electrical appliance.
- Be sure the power supply is AC 115V~ 60Hz.
Water pump drain hose
Fig.6

5
OOOO
2 COOLING OPERATION (Operating temperature range: 17 C-32 C/63 F-90 F)
- Press the "MODE"button several times until the "COOL"indicator light comes on.
- Press the "TEMP SETTING"buttons ""or ""to select your desired room temperature.
OOOO
(17 C-30 C/63 F-86 F)
- Press the "FAN SPEED"button to choose the fan speed.
OOOO
3 DEHUMIDIFYING OPERATION (Operating temperature range: 13 C-32 C/55 F-90 F)
- Press the "MODE"button several times until the "DRY"indicator light comes on.
- The fan will run at a fixed speed at this setting.
- Keep windows and doors closed for the best dehumidifying effect.
- Do not put the duct to window.
4 HEATING OPERATION (Cooling only type without heat feature)
OOOO
(Operating temperature range:5 C-30 C/41 F-86 F)
- Press the "MODE"button several times until the "HEAT"indicator light comes on.
- Press the "TEMP SETTING"buttons ""or ""to select your desired room temperature.
OOOO
(17 C-30 C/63 F-86 F)
- Press the "FAN SPEED"button to choose the fan speed.
- Do not put the duct to window.
5 FAN OPERATION
- Press the "MODE"button several times until the "FAN "indicator light comes on.
- Press the "FAN SPEED"button to choose the fan speed.
- Do not put the duct to window.
6 TIMER OPERATION
Setting the on timer:
- Press the "TIMER ON"button when the air conditioner is off. Select the time you need the unit
start to operate.
- The Operation Paned Window will display "ON"
- The starting time is adjustable from 0.00 to 24.
Setting the off timer:
- Press the "TIMER OFF"button when the air conditioner is on. Select the time you need the unit
turn off. The Operation Panel Window will display "OFF".
- The turning off time is adjustable from 0.00 to 24.
7 WATER PUMP DRAINAGE
8 CONTINUOUS DRAINAGE
- Connect the water pump drain hose to the unit before operate. When the water level of the internal
water tank reaches a predetermined level, the water pump will be activated and drain the
condensed water outside through the connected drain hose. The maximum delivery lift is 3.5m.
(Under this condition, attach the rubber blockage to the back hole to prevent continuous drainage.)
- When you plan to leave this unit unused for a long time, remove the rubber blockage form the back
hole and attach a section of the continuous drain hose to drain hose connector. All the water in the
water tank would drain outside through the drain hose. (Under this condition, the water pump is not
activated.)

6
INSTALLATION
Install the mobile ir conditioner in a flat and spacious location
where the air outlets will not be covered up. A minimum
clearance of 30cm from a wall or other obstacles should
be kept. The appliance shall not be used in the laundry.
The plug shall accessible after appliance is positioned.
Wiring shall be done according to National rules.
1 IMPORTANT:
2 DUCT MOUNT INSTRUCTIONS:
Exhaust Air Oulet
Duck
A) TEMPORARY-
1. Attach one end of the duct to the exhaust air outlet of the
mobile air condition, first fit the left side of the duct on the
exhaust air panel, then the right side duct. Push it
downwards, be sure to fix thoroughly. (See the figures)
2. Attach the other end of the duct to adaptor B.
3. Put the end of duct to a nearby window.
B) PERMANENT-
1. Attach one end of the duct to the exhaust air outlet of the
mobile air conditioner. According to the arrow direction,
first fit the left side of the duct on the exhaust air panel,
then the right side duct. Push it downwards, be sure to fix
thoroughly. (See the figures)
2. Install the adaptor A onto the wall by using 4 wall plug and
screws, be sure to fix thoroughly. (See the figures)
3. Attach the other end of the duct to adaptor A.
4. Cover the hole using the adaptor cap when not in use.
The duct can be compressed or extended between 500mm
and 2000mm, but it is desirable to keep the duct length to a
minimum.
IMPORTANT:
DO NOT OVER BEND THE DUCT (SEE FIGURE)
Adapter A
Rawlplugs
Skruer
max 120CM
min 30CM
Fig.8
Fig.9
Fig.10
30cm
30cm
Fig.7

7
Your window kit has been designed to fit most standard
Vertical and horizontal window applications, However, it
may be necessary for you to improvise/modify some aspects
of the installation procedures for certain types of window.
Please refer to Fig. 11 & Fig. 11a for minimum and maximum
window openings.
Window Kit Installation
Horizontal
window
Window Slider Kit
Minimum:67.5cm(2.22ft).
Maxmum:123cm(4.04ft).
Window Slider Kit
Minimum:67.5cm(2.22ft).
Maxmum:123cm(4.04ft).
Horizontal
window
This unit is equipped with a internal water tank, two full-safe
switch mechanisms, one is used to control the water pump
drainage, the other is used to monitor the water level inside
the internal water tank. When the water level reaches a
predetermined level, the full-safe switch mechanism is
activated. The digital display shows P1 and the water full
indicator light illuminates. Carefully move the unit outside,
remove the rubber blockage from the back drainage hole
and drain the water off. The unit will continue operating
properly.
Drain Tank Safety Feature
MAINTENANCE
1) BE SURE TO UNPLUG THE UNIT BEFORE CLEANING.
2) DO NOT USE GASOLING, THINNER OR OTHER CHEMICALS TO CLEAN THE UNIT.
3) DO NOT WASH THE UNIT DIRECTLY UNDER A TAP OR USING A HOSE. THE ELECTRICAL
CAUE DANGER.
4) IF THE POWER CORD IS DAMAGED, IT SHOULD BE REPAIRED BY MANUFACTURE OR ITS
AGENCY.
IMPORTANT:
1 AIR FILTER
- Clean the air filter at least once every two weeks to
prevent inferior fan operation because of dust.
- Removal
Pull out the filter cover and remove the air filter from the
filter cover.
- Cleaning
Wash the air filter by immersing it gently in warm water
OO
(about 40 C/104 F) with a neutral detergent. Rinse the
filter and dry it in a shady place.
- Mounting
Attach the air filter to the filter cover using the attachment
hooks on the inner surface of the cover. Put the filter cover
back to the unit.
2 UNIT ENCLOSURE
- Use a lint-free cloth soaked with neutral detergent to clean
the unit enclosure. Finished by a dry clean cloth.
Fig.11
Fig.11a
Fig.12

8
TROUBLE SHOOTING
1. UNIT DOES NOT
START WHEN
PRESSING 1/0 BUTTON
- Water full indicator blinks, water tank
is full.
Dump the water in the water tank.
TROUBLES
POSSIBLE CAUSES
SUGGEST REMEDIES
Reset the temperature.
Reset the temperature.
Make sure all the windows and
doors are closed.
Remove the heat sources if possible.
Connect the duct and make
sure it can function properly.
Decrease the set temperature.
Clean the air filter.
- Room temperature is higher than
the set temperature.(Heating mode)
- Room temperature is lower than
the set temperature.(Cooling mode)
- The windows or doors in the room
are not closed.
- There are heat sources inside the
room.
- Exhaust air duct is not connected or
blocked.
- Temperature setting is too high.
- Air filter is blocked by dust.
2. NOT COOL ENOUGH
Place the unit on a flat, level
ground if possible.
It is normal.
- The ground is not level or not flat
enough.
- The sound comes from the flowing
of the refrigerant inside the
air-conditioner.
4. NOISY OR VIBRATION
5. GURGLING SOUND
Switch on again after the unit has cool down.
- The automatic over heat protection
function. When the temperature at
OO
the air outlet exceed 70 C/158 F,the
device will stop.
3. POWER SHUT OFF AT
HEATING MODE

L imited Warranty
DAE W OO E LE C T R ONIC S AME R IC A, INC . warrants the following P ortable room air-
conditioner to be free from defective material and workmanship and agrees to remedy
any such defect or to furnish a new part (at the C ompanyÕs option) in exchange for any
part of any unit of its manufacture which under normal installation, use and service
disclosed such defect, provided the unit is delivered by the owner to store or dealer
where purchased or Daewoo authorized service center. To establish and receive
warranty service at our store, dealer or our authorized service center, a sales receipt
or bill of sales is required for proof of purchase.
This warranty does not extend to any of our electronic products which have been
subjected to misuse, neglect, accident, incorrect wiring not our own, improper
installation, unauthorized modification, or to use in violation of instructions furnished by
us, nor units which have been repaired or altered outside of our factory, nor to cases
where the serial number thereof has been removed, defaced, or changed.
This warranty is in lieu of all warranties expressed or implied and no representative or
person is authorized to assume for us any other liability in connection with the sales of
our electronic products.
Over the counter exchange for units that are initially defective. Initial defective is
described as when the dealer opens the unit and finds that it is inoperative or an
individual customer opening a new unit and finding that it is initially defective. T his unit
may be returned to the factory by the dealer for exchange. Under no circumstances
will an individual customer be permitted to return defective unit directly to factory.
E xchange must be directly with the dealer. When this unit is returned to dealer, a copy
of the purchase evidence stating the date of purchase is to be put in the individual box
for dealerÕs further control with the factory.
MODE L P AR TS LAB OR C OMP R E S S OR
DOC -091R 1 year 1 year 5 years
DOC -091R H
Note: T he warranty service center list is constantly changing with the addition of our
current qualified service centers. If there is inadequate or no local service facility,
subject individual customer will call DAE WOO on the toll free number
1-800-DAE WOO8(1-800-323-9668) to be provided with further informations.