Dahua VTO12 Series User manual

Unit Door Station User's Manual
----VTO12XX Series
V1.2.0

i
Welcome
Thank you for purchasing our product!
This quick start guide is designed to be a reference tool for your system.
Please keep it well for future reference!

ii
Important Safeguards and Warnings
Please read the following safeguards and warnings carefully before using the product in
order to avoid damages and losses.
Note:
 Do not expose the device to lampblack, steam or dust. Otherwise it may cause
fire or electric shock.
 Do not install the device at position exposed to sunlight or in high temperature.
Temperature rise in device may cause fire.
 Do not expose the device to humid environment. Otherwise it may cause fire.
 The device must be installed on solid and flat surface in order to guarantee
safety under load and earthquake. Otherwise, it may cause device to fall off or
turnover.
 Do not place the device on carpet or quilt.
 Do not block air vent of the device or ventilation around the device. Otherwise,
temperature in device will rise and may cause fire.
 Do not place any object on the device.
 Do not disassemble the device without professional instruction.
Warning:
 Please use battery properly to avoid fire, explosion and other dangers.
 Please replace used battery with battery of the same type.
 Do not use power line other than the one specified. Please use it properly.
Otherwise, it may cause fire or electric shock.
Special Announcement
 This manual is for reference only.
 All the designs and software here are subject to change without prior written
notice.
 All trademarks and registered trademarks are the properties of their respective
owners.
 If there is any uncertainty or controversy, please refer to the final explanation of
us.
 Please visit our website for more information.

iii
Table of Contents
1Product Overview ........................................................................................ 1
1.1 VTO1210A/VTO1210A-X/VTO1220A .............................................................. 1
1.2 VTO1210B(W)-X/VTO1220B(W) ..................................................................... 4
1.3 VTO1210C-X .................................................................................................. 6
2Basic Functions ........................................................................................... 9
2.1 Call.................................................................................................................. 9
2.2 Modify Local Config ......................................................................................... 9
2.2.1 Enter Project Settings Interface ............................................................. 9
2.2.2 Modify IP, Gateway and Subnet Mask................................................... 9
2.2.3 Modify Volume Config ......................................................................... 10
2.3 Issue Card ..................................................................................................... 10
2.4 Password Function ........................................................................................ 10
2.4.1 Unlock from VTH and Center .............................................................. 10
2.4.2 Unlock from Local ............................................................................... 10
2.4.3 Unlock via IC card ............................................................................... 11
2.5 VTO Web Function ........................................................................................ 11
2.5.1 Web Login ........................................................................................... 11
3Web Function ............................................................................................ 12
3.1 Overview ....................................................................................................... 12
3.2 System Config ............................................................................................... 13
3.2.1 Login Config ........................................................................................ 13
3.2.2 Indoor Station(VTH) Manager ............................................................. 15
3.2.3 LAN Setting ......................................................................................... 16
3.2.4 Network Setting ................................................................................... 17
3.2.5 Change Password ............................................................................... 18
3.3 Info Search .................................................................................................... 18
3.4 Status Statistics............................................................................................. 19
3.5 Logout ........................................................................................................... 19
4Debug System ........................................................................................... 21

iv
4.1 Debug Digital System .................................................................................... 21
4.1.1 Configure VTO .................................................................................... 21
4.1.2 Configure Digital VTH ......................................................................... 22
4.1.3 Create Digital System ......................................................................... 22
4.2 Debug Analog System................................................................................... 22
4.2.1 Configure VTO .................................................................................... 23
4.2.2 Create Analog System ........................................................................ 23
4.2.3 Configure Analog VTH ........................................................................ 23
5FAQ ........................................................................................................... 24
Appendix 1 Specifications ....................................................................................... 25
Appendix 2 Device Port ........................................................................................... 27
Appendix 3 Installation ............................................................................................ 31

1
1 Product Overview
Connect the device to the power, the system boots up properly. After about one minute,
the screen turns on and the boot-up completes, system goes to the normal working
interface. The front panel is shown as in Figure 1-1, Figure 1- 2 and Figure 1-3.
1.1 VTO1210A/VTO1210A-X/VTO1220A
Figure 1- 1 VTO1210A/VTO1210A-X/VTO1220A
Please refer to the following sheet for detailed information.
SN
Name
Function
1
Logo
Decoration logo.
2
Photo Sensor
It can detect the environment light. It is a
compensation light option.

2
3
Compensation Light
It can compensate the camera light in
the low illumination environments.
4
Microphone
Audio input
5
Key Panel
1. Button.
a) Backspace function. It is to delete
the previous symbol.
b) Hang up function. It is to hang up
the call.
2. Number button. Input the number 0 to
9.
3. button. When you are using the
password to open the door. Press this
button once to begin input. After you
input the password, please press it again
to complete the operation.
4. Call button. After you input the
room number, press it to begin a dial up.
5. Call center button. Press it to
call the center directly.
6
Speaker
Output audio
7
Card Induction zone
Use the card to open the door.
8
LCD
Here you can view prompt information,
date, time and etc.
Note:
1. ―Call: Room No. + ↑ ‖. Please input
the room number first and then press the
button to dial；
2.‖Call Center: Press button‖. Please
press the button to call center.
3.―Password： + password + ‖，
If you want to open the door via the
password, please press the button
and then input the room number and

3
password. Please press the button
to confirm.
9
Camera
It is to monitor the video of the door.

4
1.2 VTO1210B(W)-X/VTO1220B(W)
Figure 1- 2 VTO1210B(W)-X/VTO1220B(W)
Please refer to the following sheet for detailed information.
SN
Name
Function
1
Logo
Printed logo.
2
Microphone
Audio input
3
Compensation Light
It can compensate the camera light in
the low illumination environments.
4
Approaching
Induction
It can detect approaching body.

5
5
Speaker
Output audio
6
Key Panel
1. Button.
a) Backspace function. It is to delete
the previous symbol.
b) Hang up function. It is to hang up
the call.
2. Number button. Input the number 0 to
9.
3. button. When you are using the
password to open the door. Press this
button once to begin input. After you
input the password, please press it again
to complete the operation.
4. Call button. After you input the
room number, press it to begin a dial up.
5. Call center button. Press it to call
center directly.
7
Card Induction Zone
Use the card to open the door.
8
LCD
Here you can view prompt information,
date, time and etc.
Note:
1. ―Call: Room No. + ‖. Please input
the room number first and then press the
button to dial；
2.‖Call Center: Press button‖. Please
press the button to call center.
3.―Password： + password + ‖， If
you want to open the door via the
password, please press the button
and then input the room number and
password. Please press the button
to confirm.

6
9
Camera
It is to monitor the video of the door.
1.3 VTO1210C-X
Figure 1- 3 VTO1210C-X
Please refer to the following sheet for detailed information.
SN
Name
Function
1
Logo
Printed logo.
2
Microphone
Audio input
3
Compensation Light
It can compensate the camera light in
the low illumination environments.
4
Speaker
Output audio

7
5
Key Panel
1. Button.
c) Backspace function. It is to delete
the previous symbol.
d) Hang up function. It is to hang up
the call.
2. Number button. Input the number 0 to
9.
3. button. When you are using the
password to open the door. Press this
button once to begin input. After you
input the password, please press it again
to complete the operation.
4. Call button. After you input the
room number, press it to begin a dial up.
5. Call center button. Press it to call
center directly.
6. button: In contacts interface,
press these buttons to page up and
down. They can be customized for
special function.
6
Card Induction Zone
Use the card to open the door.
7
LCD
Here you can view prompt information,
date, time and etc.
Note:
1. ―Call: Room No. + ‖. Please input
the room number first and then press the
button to dial；
2.‖Call Center: Press button‖. Please
press the button to call center.
3.―Password： + password + ‖， If
you want to open the door via the
password, please press the button
and then input the room number and

8
password. Please press the button
to confirm.
8
Camera
It is to monitor the video of the door.

9
2 Basic Functions
2.1 Call
Under standby status (Figure 1-1, Figure 1- 2), press or button, this VTO will call
center. The video door phone begins when the port picks up. During the whole process,
you can press the button or to end current talk and return to the standby
interface.
Under standby status, enter room no. or press or to select room no. in contacts,
and press or to call VTH. The video door phone begins when the VTH picks up.
During the whole process, you can press the button or to end current talk and
return to the standby interface.
2.2 Modify Local Config
2.2.1 Enter Project Settings Interface
In the standby status, press or , input password as 888888 and then press or
to enter installation setup interface. Select up/down via button 2 and 8, press or
to enter sub-interface.
2.2.2 Modify IP, Gateway and Subnet Mask
In project settings --- IP setup interface, select up/down/left/right via button 2,8,4,6, press
or to enter/exit IP modification status. When you finish, press or to exit
modification interface.

10
2.2.3 Modify Volume Config
In volume interface, adjust volume via button 4 and 6. When you finish, press or
to exit modification interface.
2.3 Issue Card
In card issuing interface, select to issue card with parent card or password via button 2
and 8. Press or to enter sub-interface.
Issue with parent card: Under issuing card with parent card interface, fill in room no. of the
card to be authorized, and swipe it. When it says the card has been authorized
successfully, press or to exit.
Issue with password: Under issuing card with password interface, enter issuing password
002236, press or to enter, fill in room no. of the card to be authorized, and swipe
it. When it says the card has been authorized successfully, press or to exit.
2.4 Password Function
2.4.1 Unlock from VTH and Center
During calling, talk and monitoring statuses, the center or the VTH can open the door lock
of the device remotely. System returns to the standby interface after phone hangs up or
the countdown is complete.
2.4.2 Unlock from Local
VTO WEB page – A&C Manager—Password Unlock Type, select either uniform password
or self password.
Uniform password: In standby interface, press or , input default password:
123456, press or to unlock. Defualt password can be changed in A&C Manager
interface.
Self password: n standby interface, press or , input 4-digit room no. + default

11
password: 123456, press or to unlock. For example, to unlock room 101, you
shall input: #0101123456#. Defualt password can be changed in A&C Manager interface.
2.4.3 Unlock via IC card
The door is open after you swipe IC card and the card passed the authentication and
station verification.
2.5 VTO Web Function
2.5.1 Web Login
Access VTO from PC, input the IP address of VDP in your explorer to enter the web login
page. Input username: admin and password: admin, then you can enter its web page
where you can configure the VTO. Please refer to the following chapter for details.

12
3 Web Function
3.1 Overview
The web-based interface is shown in Figure 3- 1.
Web function supports VTO1220A, VTO1220B, VTO1210A-X, VTO1210B(W)-X and
VTO1210C-X. The webpage of each device may be slightly different. Here makes
1210B-X an example:
Figure 3- 1
Please refer to the following sheet for detailed information.
SN
Name
Function
1
System Config
You can set VTO1210B-X device parameter and
network info.
2
Info Search
You can search VTO1210B-X call history.
3
Status Statistics
You can perform statistics of VTH status under
VTO1210B-X.
4
Logout
You can control reboot of VTO1210B-X and
shutdown of WEB server.

13
3.2 System Config
3.2.1 Login Config
Input VTO IP address in address field of IE Explorer as in Figure 3- 2.
Figure 3- 2
You must input username and password in order to login WEB main interface.
Default username: admin
Default password: admin.
After you login, you will see 4 major settings: system, info search, status statistics, and
Logout.
3.2.1.1 Local Setting
The following is the instruction for major settings:
1. Frame: For NTSC standard, please select 30 frame/s. For Pal standard, please select
25 frame/s.
2. One-key clear: You may restore all settings on VTO to default after pressing this
button and confirm. Be careful!
3. Video format has two types of resolution:
 D1: 704x576
 WVGA: 800x480
Please see Figure 3- 3.

14
Figure 3- 3
3.2.1.2 A&C Manager
Click on Local Config and then click on A&C Manager. You may change password here
and please keep in mind that the default password is 123456. To unlock door, please input
#123456#. You also can set unlock responding interval and unlock period.
FTP address: FTP address is used to store snapshot taken at VTO when someone swipes
card. User can login FTP to view those photos.
Figure 3- 4

15
3.2.2.3 System Time
Click on Local Config and then click on System Time. You may set time in the following
interface as in Figure 3- 5. You may also synchronize system time with your local PC.
Figure 3- 5
3.2.2 Indoor Station(VTH) Manager
Indoor Station Manager mainly includes adding digital/analog VTH, deleting VTH and
editing VTH user. VTO1210A-X and VTO1210B-X have digital and analog indoor station
manager. VTO1220A only has digital indoor station manager.
3.2.2.1 Digital Indoor Station Manager
In Digital Indoor Station Manager interface, check box display resident info enable to
display successfully configured VTH info as shown in Figure 3- 6. Click on Add button at
the left lower corner, and input user name and VTH short number. Please be notified that
only VTH number is required for operation as default.