Dahua DHI-VTO4202F Series User manual

Intercom Modular Outdoor Station
DHI-VTO4202F Series
User’s Manual
V1.0
.2

I
Foreword
General
This manual offers reference material and general information about the basic operation,
maintenance, and troubleshooting for a Dahua security device. Read, follow, and retain the
following safety instructions. Heed all warnings on the unit and in the operating instructions
before operating the unit. Keep this guide for future reference.
Safety Instructions
The following categorized signal words with defined meaning might appear in the Guide.
Signal Words
Meaning
WARNING
Indicates a medium or low potential hazard that, if not avoided,
could result in slight or moderate injury.
CAUTION
Indicates a potential risk that, if not avoided, could result in
property damage, data loss, lower performance, or unpredictable
results.
NOTE Provides additional information as the emphasis and supplement
to the text.
Revision History
No.
Version
Revision Content
Release Time
1 V1.0.0 First Release. January 2019
2 V1.0.1 Revised for North America July 2019
3 V1.0.3 Minor Formatting and
Typographical Corrections June 2021
Privacy Protection Notice
As the device user or data controller, you may collect personal data such as face images,
fingerprints, license plate number, email address, phone number, GPS location and other
sensitive or private information. Yo u must ensure that your organization complies with local
privacy protection laws and regulations to protect the legitimate rights and interests of other
people by implementing measures including but not limited to providing clear and visible
identification to inform data subjects of the existence of surveillance area and providing related
contact

II
About the Guide
This user guide has been compiled with great care and the information it contains has
been thoroughly reviewed and verified.
The text was complete and correct at the time of printing. This guide may be periodically
updated to reflect changes to the product or to correct previous information and the
content of this guide can change without notice.
If you encounter an error or have, any questions regarding the contents of this guide,
contact customer service for the latest documentation and supplementary information.
Dahua accepts no liability for damage resulting directly or indirectly from faults,
incompleteness, or discrepancies between this guide and the product described. Dahua is
not liable for any loss caused by installation, operation, or maintenance inconsistent with
the information in this guide.
All the designs and software are subject to change without prior written notice. The
product updates may cause some differences between the actual product and the Guide.
Contact the customer service for the latest program and supplementary documentation.
Video loss is inherent to all digital surveillance and recording devices; therefore, Dahua
cannot be held liable for any damage that results from missing video information. To
minimize the occurrence of lost digital information, Dahua recommends multiple,
redundant recording systems, and adoption of backup procedures for all data.
All trademarks, registered trademarks and the company names in the Guide are the
properties of their respective owners.
Please visit our website, contact the supplier, or customer service if a problem occurs
when using the device.
Contact the supplier or customer service if you encounter any issues while using this unit.

III
Important Safeguards and Warnings
This chapter describes the contents covering proper handling of the device, hazard prevention,
and prevention of property damage. Read these contents carefully before using the device,
comply with them when using, and keep it for future reference.
Installation and Maintenance Professionals Requirements
All installation and maintenance professionals must have adequate qualifications or
experiences to install and maintain CCTV systems and electric apparatus. The
professionals must have the following knowledge and operation skills:
Basic knowledge and installation of CCTV systems.
Basic knowledge and operation skills of low voltage wiring and low voltage electronic
circuit wire connection.
Basic knowledge and operation skills of electric apparatus installation and maintenance in
hazardous sites.
Power Requirements
Install the unit in accordance with the manufacturer’s instructions and in accordance with
applicable local codes.
All installation and operation must conform to your local electrical safety codes.
Do not overload outlets and extension cords, which may cause fire or electrical shock.
Do not place the camera near or in a place where the camera may contact overhead
power lines, power circuits, or electrical lights.
Ensure power conforms to SELV (Safety Extra Low Voltage) and that the limited power
source is rated AC 24V as specified in IEC60950-1. (Power supply requirement is subject
to the device label).
All input/output ports are SELV circuits. Ensure that SELV circuits are connected only to
other SELV circuits.
Ground the unit using the ground connection of the power supply to protect the unit from
damage, especially in damp environments.
Please install easy-to-use device for power off before installing wiring, which is for
emergent power off when necessary.
Protect the plug and power cord from foot traffic, being pinched, and its exit from the unit.
Do not attempt to service the unit. Opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to qualified personnel.
If the unit is damaged and requires service, unplug the unit from the main AC power
supply and from the PoE supply and refer to qualified service personnel. Damage may
include, but is not limited to:
The power supply cord or plug is damaged.
Liquid has spilled in or on the unit.
An object has fallen on the unit.
The unit has been dropped and the housing is damaged.
The unit displays a marked change in performance.
The unit does not operate in the expected manner when the user correctly follows the
proper operating procedures.

IV
Ensure a service technician uses replacement parts specified by the manufacturer, or that
have the same characteristics as the original parts. Unauthorized parts may cause fire,
electrical shock, or other hazards. Dahua is not liable for any damage or harm caused by
unauthorized modifications or repairs.
Perform safety checks after completion of service or repairs to the unit.
Use attachments and accessories only specified by the manufacturer. Any change or
modification of the equipment, not expressly approved by Dahua, could void the warranty.
Incorporate a readily accessible disconnect device in the building installation wiring for
quick power disconnect to the camera.
Dahua assumes no liability or responsibility for any fire or electrical shock caused by
improper handling or installation.
Application Environment Requirements
Please use the device within the allowed humidity (<95%RH) and altitude (<3000m).
Transport, use, and store the unit within the specified temperature and humidity range.
Do not place the unit in a wet, dusty, extremely hot or an extremely cold environment; and
avoid environments with strong electromagnetic radiation or unstable lighting.
Do not use the device in the corrosive environment such as high salt fog area (sea, beach
and coastal area), acid gas environment and chemical plants.
Do not use the device in applications with strong vibrations such as in boats and vehicles.
Never push objects of any kind into this unit through openings as they may touch
dangerous voltage points or cause a short circuit that may result in fire or electrical shock.
Take care to not spill any liquid on the unit.
If your installation environment is subjected to one of the conditions above, contact our
sales staff to purchase cameras intended for the particular environment.
Do not install the device near the place with heat source, such as radiator, heater, stove or
other heating equipment, which is to avoid fire.
Do not aim the lens at an intense radiation source (such as the sun, a laser, and molten
steel for example) to avoid damage to the thermal detector.
Use the factory default package or material with equal quality to pack the device when
transporting.
Operation and Maintenance Requirements
Do not touch the heat dissipation component of the unit. This part of the unit is hot and
may cause a burn.
Do not open or dismantle the device; there are no components that a user can fix or
replace. Opening the unit may cause water leakage or expose components to direct light.
Contact the manufacturer or a qualified service representative to service the camera or to
replace a component, including the desiccant.
Dahua recommends the use of a thunder-proof device in concert with the unit.
Do not touch the CCD or the CMOS optic sensor. Use a blower to clean dust or dirt on the
lens surface. Use a dry cloth dampened with alcohol and gently wipe away any dust on
the lens.

V
Use a dry soft cloth to clean the unit’s housing. If the unit is particularly dusty, use water to
dilute a mild detergent, apply the diluted detergent to a soft cloth, and then gently clean
the device. Finally, use a dry cloth to wipe the unit dry. Do not use a volatile solvent like
alcohol, benzene, or thinner; or use a strong detergent with abrasives, which may damage
the surface coating or reduce the working performance of the unit.
Do not touch or wipe a dome cover during installation; this cover is an optical device.
Refer to the following methods clean the dome cover:
Stained with dirt: Use an oil-free soft brush or blower to gently remove the dirt.
Stained with grease or fingerprints: Use a soft cloth to wipe gently the water droplet or the
oil from the dome cover. Then, use an oil-free cotton cloth or paper soaked with alcohol or
detergent to clean the lens from the center of the dome to the outside edge. Change the
cloth several times to ensure the dome cover is clean.
WARNING
Modify the default password after login.
Use attachments and accessories only specified by the manufacturer. Any change or
modification of the equipment, not expressly approved by Dahua, could void the warranty.
Internal and external ground connection should be stable.
Do not supply power via the Ethernet connection (PoE) when power is already supplied
via the power connector.
Disconnect power before device maintenance and overhaul. It is prohibited to open the
cover with power on in an explosive environment.
Please contact the local dealer or the nearest service center if the device fails to work
normally, please do not dismantle or modify the device.

VI
Cybersecurity Recommendations
Mandatory actions to be taken towards cybersecurity
Change Passwords and Use Strong Passwords
The number one reason systems are “hacked” is due to having weak or default
passwords. It is recommended to change default passwords immediately and choose
a strong password whenever possible. A strong password should be made up of at
least eight characters and a combination of special characters, numbers, and upper
and lower case letters.
Update Firmware
As is standard procedure in the tech-industry, we recommend keeping NVR, DVR,
and IP camera firmware up-to-date to ensure the system is current with the latest
security patches and fixes.
Recommendations to improve your network security
Change Passwords Regularly
The length should be greater than 8 characters;
Include at least two types of characters; character types include upper and lower case
letters, numbers, and symbols;
Do not use an account name or the account name in reverse order;
Do not use sequential characters, such as 123, abc, etc.;
Do not use repeated characters, such as 111, aaa, etc.;
Change Default HTTP and TCP Ports
Change default HTTP and TCP ports for systems. These are the two ports used to
communicate and to view video feeds remotely.
These ports can be changed to any set of numbers between 1025 and 65535.
Avoiding the default ports reduces the risk of outsiders being able to guess which
ports you are using.
Update Firmware and Client Software
Keep your network-enabled equipment (such as NVRs, DVRs, IP cameras, etc.)
firmware up-to-date to ensure the system is equipped with the latest security patches
and fixes. When the equipment is connected to the public network, it is recommended
to enable the “auto-check for updates” function to obtain timely information of firmware
updates released by the manufacturer.
Download and use the latest version of client software.
Enable HTTPS/SSL
Set up an SSL Certificate and enable HTTPS to encrypt all communication between
your devices and recorder.
Enable IP Filter
Enable the IP filter to prevent unauthorized access to the system.
Change ONVIF Password
Older IP camera firmware does not automatically change the ONVIF password when
the system credentials are changed. Update the camera’s firmware to the latest
revision or manually change the ONVIF password.

VII
Forward Only Ports You Need
Forward only the HTTP and TCP ports that are requited. Do not forward a wide range
of numbers to the device. Do not DMZ the device's IP address.
Do not forward any ports for individual cameras if they are all connected to a recorder
on site. Simply forward the NVR port.
Use a Different Username and Password for DSS
Do not use a username/password combination that you have in use for other
accounts, including social media, bank account, or email in case the account is
compromised. Use a different username and password for your security system to
make it difficult for an unauthorized user to gain access to the IP system.
Limit Features of Guest Accounts
Ensure that each user has rights to features and functions they need to perform their
job.
Disable Unnecessary Services and Choose Secure Modes
Turn off specific services, such as SNMP, SMTP, and UPnP, to reduce network
compromise from unused services.
It is recommended to use safe modes, including but not limited to the following
services:
SNMP: Choose SNMP v3 and set up strong encryption passwords and authentication
passwords.
SMTP: Choose TLS to access a mailbox server.
FTP: Choose SFTP and use strong passwords.
AP hotspot: Choose WPA2-PSK encryption mode and use strong passwords.
Multicast
Multicast is used to share video streams between two recorders. Currently there are
no known issues involving Multicast. Deactivate this feature if not in use to enhance
network security.
Check the Log
The information stored in the network log file is limited due to the equipment’s limited
storage capacity. Enable the network log function to ensure that the critical logs are
synchronized to the network log server if saving log files is required.
Check the system log if you suspect that someone has gained unauthorized access to
the system. The system log shows the IP addresses used to login to the system and
the devices accessed.
Physically Lock Down the Device
Perform physical protection to equipment, especially storage devices. For example,
place the equipment in a special computer room and cabinet, and implement access
control permission and key management to prevent unauthorized personnel from
accessing the equipment.
Connect IP Cameras to the PoE Ports on the Back of an NVR
Cameras connected to the PoE ports on the back of an NVR are isolated from the
outside world and cannot be accessed directly.
Isolate NVR and IP Camera Network
Ensure that the network for the NVR and IP cameras should not be the same network
as a public computer network. Separate networks prevent unauthorized users
accessing the same network the security system.

VIII
Secure Auditing
Check online users regularly to ensure unauthorized accounts are not logged in to a
device.
Check the equipment log to access the IP addresses used to login to devices and
their key operations.

IX
Table of Contents
Foreword ..........................................................................................................................................................I
Important Safeguards and Warnings........................................................................................................... III
Cybersecurity Recommendations............................................................................................................ VI
1 Overview.......................................................................................................................................................1
2 Intercom Modules ........................................................................................................................................2
Camera Module........................................................................................................................................................................2
Status Light Panel....................................................................................................................................................................4
Five-button Call Panel............................................................................................................................................................5
Keypad Module........................................................................................................................................................................6
IC Card Reader ..........................................................................................................................................................................7
Fingerprint Reader ..................................................................................................................................................................8
Information Text Display .......................................................................................................................................................9
Blank Module ............................................................................................................................................................................9
Making Cascade Connections.......................................................................................................................................... 10
3 Initializing the VTO.....................................................................................................................................11
4 Login and Reset the Password...................................................................................................................12
Login ......................................................................................................................................................................................... 12
Resetting the Password...................................................................................................................................................... 13
5 Main Interface ............................................................................................................................................14
6 Local Settings .............................................................................................................................................15
Basic .......................................................................................................................................................................................... 15
Video and Audio.................................................................................................................................................................... 16
Access Control Settings...................................................................................................................................................... 18
6.3.1 Local............................................................................................................................................................................. 18
6.3.2 RS-485.......................................................................................................................................................................... 19
6.3.3 Password Management......................................................................................................................................... 19
System...................................................................................................................................................................................... 20
Security .................................................................................................................................................................................... 21
Wiegand................................................................................................................................................................................... 22
Onvif User................................................................................................................................................................................ 23
Upload File.............................................................................................................................................................................. 23
7 Household Setting .....................................................................................................................................24
VTO No. Management......................................................................................................................................................... 24
VTH Management ................................................................................................................................................................ 25
7.2.1 Adding Room Number .......................................................................................................................................... 25
7.2.2 Issuing an Access Card........................................................................................................................................... 29
7.2.3 Reading Fingerprints for Access ......................................................................................................................... 30
VTS Management ................................................................................................................................................................. 30
IP Camera Setting................................................................................................................................................................. 31
Status........................................................................................................................................................................................ 33
Publish Information............................................................................................................................................................. 33
7.6.1 Send Info .................................................................................................................................................................... 33
7.6.2 History Info ................................................................................................................................................................ 34

X
8 Network ......................................................................................................................................................35
Basic .......................................................................................................................................................................................... 35
8.1.1 TCP/IP........................................................................................................................................................................... 35
8.1.2 Port............................................................................................................................................................................... 36
8.1.3 P2P................................................................................................................................................................................ 36
UPnP.......................................................................................................................................................................................... 36
8.2.1 Enabling UPnP Services......................................................................................................................................... 37
8.2.2 Adding UPnP Services............................................................................................................................................ 37
SIP Server................................................................................................................................................................................. 38
Firewall ..................................................................................................................................................................................... 39
9 Log Management .......................................................................................................................................40

1
1Overview
The Dahua Intercom Modular System is a complete intercom solution that offers full customization of
the entire system. This intercom system starts with a 2 MP outdoor video intercom module that offers
a wide-angle view lens, high-resolution images even in dark environments, and two-way talk. Then,
add optional modules that offer door access capability (card reader, fingerprint reader, and keypad),
call buttons, information text display, and status light indicators. The system also offers optional
accessories to flush-or surface-mount a two-or three-module intercom system.
1.1 Modular Intercom Components
•DHI-VTO4202F-P-S2: 2 MP Outdoor Video Intercom (Required)
•DHI-VTO4202F-MB5: Five-button Call Panel
•DHI-VTO4202F-MF: Fingerprint Reader
•DHI-VTO4202F-MK: Keypad
•DHI-VTO4202F-ML: Status Light Panel
•DHI-VTO4202F-MN: Blank Panel
•DHI-VTO4202F-MR: IC Card Reader
•DHI-VTO4202F-MS: Information Text Display

2
2Intercom Modules
Camera Module
Front Panel
Ref
Name
Description
1 MIC Inputs audio.
2 Camera Monitors door area.
3 Speaker Outputs audio.
Rear Panel

3
Ref
Name
Description
1 Tamper Switch
The VTO issues an alarm sound if it is removed from the
wall by force, and sends the alarm to the management
center.
2 Ports Connect to power supply, electric control lock, solenoid
lock, and exit button.
3 Ethernet Port Connects unit to Ethernet network.
4 Cascade Connection Connection to another Intercom module.
Ports
Ref
Name
Ref
Name
1 GND 8 EOC1 (2wires –(GND)
for a 2-wire camera module)
2 +12V_OUT 9 DOOR_BUTTON
3 RS-485_B 10 DOOR_FEEDBACK
4 RS-485_A 11 GND
5 ALARM_NO 12 DOOR_NC
6 ALARM_COM 13 DOOR_COM
7 EOC2 (2wires +(48V)
for a 2-wire camera module)
14 DOOR_NO

4
Status Light Panel
Front Panel
Ref
Description
1 Call indicator
2 Talk indicator
3 Unlock indicator
Rear Panel
Ref
Description
1 Cascade input
2 Cascade output

5
Five-button Call Panel
Ref
Name
Description
1 User directory Add a physical name cards to the slots.
2 Call buttons Call a VTH Monitor or the management center.
Requires programming in the VTO interface.
Rear Panel
Ref
Description
1 Cascade input
2 Cascade output

6
Keypad Module
Ref
Description
1 Selection
2 Numbers
3 Place call
4 Call management center
Rear Panel
Ref
Description
1 Cascade input
2 Cascade output

7
IC Card Reader
Rear Panel
Ref
Description
1 Cascade input
2 Cascade output

8
Fingerprint Reader
Rear Panel
Ref
Description
1 Cascade input
2 Cascade output

9
Information Text Display
Rear Panel
Ref
Description
1 Cascade input
2 Cascade output
Blank Module
This module is used to cover extra space if no other functional modules are needed.