Daikin DCS601C51 User manual

Hardware Manual
Use smart and save smart
● Thank you for purchasing intelligent Touch Controller.
● This operation manual contains notes for safe use of the
product.
For correct use, be sure to read this manual
carefully before use.
Store this manual close at hand so that it can be referred
to as required.
Model
DCS601C51
MAC ADDRESS
intelligent Touch Controller
We use recycled paper for making this operation manual.
Maintenance
Precautions 6
Maintenance
LCD Maintenance 7
When Leaving the Product
Turned OFF for a Long Time 7
Troubleshooting 8
Maintenance
For Your Information
Before use
Before use
Safety Instructions
Be sure to follow the instructions below 1
System Overview 3
Part Names and Functions 4
For Your Information
Options 12
Specification 13
After-sales Service 14
3P073677-12P04.11.226:40PMページ1

Instructions given here are classified into the following two categories.
Instructions in both categories are important for safety and must be duly followed.
Caution
Warning
Failure to follow the instruction may lead to serious consequences including death or
serious injury.
Failure to follow the instruction may cause injury or material damage, which, in some
cases, leads to serious consequences.
The symbol given in the manual shows the following:
Do not attempt to do things described in the
instruction.
Be sure to provide grounding as required. Absolutely avoid exposing the unit to water.
Be sure to follow the instruction.
Be sure to follow the instructions below
Safety Instructions
Read the manual carefully in advance for correct use
When any abnormality (such as burnt smell) is
generated, turn the power OFF and contact the
dealer you purchased the product from.
Continuing to operate with
the abnormality left
unattended may cause
failure, electric shock or fire.
For remodelling or repair, contact the dealer
you purchased the product from.
Failure to remodel or repair
properly may cause water leak,
electric shock or fire.
For transferring or reinstallation, contact the
dealer you purchased the product from.
Failure to install properly may
cause water leak, electric shock
or fire.
Warning Notes on use for users
Do not touch the inside of the controller.
Do not remove the front panel.
Touching the inside is dangerous
and may cause failure.
For inspection and
adjustment
of the inside of the controller,
contact the dealer you
purchased the product from.
1
3P073677-12P04.11.226:40PMページ2

Do not install in a place subject to flammable
gas.
Leakage of gas resulting in
accumulation around the unit
may lead to ignition.
Do not install in a place subject
to direct sunlight.
Failure to follow the
instruction may lead to
discoloring of the LCD
that hinders proper
display.
Be sure to provide grounding.
Do not connect the grounding
wire to any gas pipe, water pipe,
lightning rod or telephone
grounding.
Inappropriate grounding may
lead to electric shock.
Do not install the controller in a place subject
to water.
Water in the device may lead
to electrical leak and failure
in the electronic components
inside.
Do not wipe the surface of the controller touch
panel with benzine, thinner or chemically-
treated dust cloth.
Failure to follow the instruction may
lead to discoloring or peeling of the
paint. Any soiling must be wiped off
with a piece of cloth soaked in a
diluted neutral
detergent and
wrung sufficiently.
Wipe again with a
dry piece of cloth.
To clean, be sure to stop operation and turn the
power OFF.
Failure to follow the
instruction may lead to
electric shock or injury.
Washing may lead to
electric shock.
Be sure to operate with the touch pen provided.
Failure to follow the
instruction may lead to
damage or failure.
Do not wash the controller
with water.
No exposure to
water allowed!
No exposure to
water allowed!
Caution Notes on use for users
benzine thinner
2
Before use
3P073677-12P04.11.226:40PMページ3

System Overview
This intelligent Touch Controller is capable of controlling/monitoring up to 64 groups of indoor units (hereafter
“groups”).
The main functions of the intelligent Touch Controller include:
1. Collective starting/stopping of operation of the indoor units connected to the intelligent Touch Controller.
2. Starting/stopping of operation, temperature setting, switching between temperature control modes and
enabling/disabling of operation with the hand-held remote control by zone or group .
3. Scheduling by zone or group .
4. Monitoring of the operation status by zone or group .
5. Display of the air conditioner operation history.
6. Compulsory contact stop input from the central monitoring panel (non-voltage, normally-open contact).
7. Power distribution of the air conditioners. (With the optional DCS002C51)
8. Control and Monitoring of air conditioner with personal computer by the Controller (with the optional
DCS004A51).
∗ A group of indoor units include:
∗ Zone control with the intelligent Touch Controller
∗ Zone control, which allows collective settings for more than one group, is available with the intelligent Touch
Controller, which facilitates the setting operations.
q One indoor unit without a remote control.
e Up to 16 indoor units controlled with one or two remote controls.
• One setting makes the same setting for all of the units in one zone.
• Up to 128 zones can be set with one intelligent Touch Controller.
(The maximum number of groups in one zone is 64.)
• Groups can be zoned at will with the intelligent Touch Controller.
• Units in one group can be divided into more than one zone.
w One indoor unit controlled with one or two remote controls.
intelligent Touch Controller
Zone 1
Up to 16 units Up to 16 unitsTwo remote controlsRemote control
No remote control Remote control Remote control
or
Indoor unit
Zone 5
Zone 2 Zone 3 Zone 4
3
3P073677-12P04.11.226:40PMページ4

Be sure to use the touch pen for
operation of the touch panel of
the intelligent Touch Controller.
Operating with an object other
than the touch pen provided may
cause damage and failure.
Note
Part Names and Functions
Color LCD with Touch Panel
Provides a display for monitoring
and operation.
Be sure to use the touch pen
provided for operation.
PCMCIA Card Slot
Used when using the optional
Power Proportional Distribution
(DCS002C51) or updating the
intelligent Touch Controller
software to a newer version.
Touch Pen
4
Use the touch pen for operation.
Be sure to use the touch pen for
operation.
Use caution not to lose the touch
pen.
When the pen is lost, contact the
dealer you purchased the
product from.
Front and Side View
Before use
3P073677-12P04.11.226:40PMページ5

Terminals on the Back of intelligent Touch Controller
Using D3-NET Plus adapter
being sold as an accessory,
you can increase the number
of indoor units to be controlled.
RS232-C connector for
D3-NET Plus adapter
When using AIRNET service,
connect it to the telephone line.
Modem connector for AIRNET
This is used when distributing the power supply to indoor
units using optional Power Proportional Distribution software
sold separately and when stopping the indoor units
compulsorily by contact input.
The size of terminal block is M3.5.
Terminal block for watt hour meter and force stop
input of indoor units
When monitoring and operating
the indoor units using the optional
Web and E-mail function software
sold separately, connect to LAN
via Ethernet cable.
Ethernet connector for web
Securely connect the earth wire.
Terminal size is M4.
Earth terminal block
Connect to AC100-240V power supply.
Terminal size is M4.
Terminal block for power supply
The terminal size of the terminal
block for communication with
indoor units is M3.5.
Terminal block for D3-NET
communication
LINE
COM L0Dil Pi3 COM Pi2 Pi1 F2 F1 L2 L1
PHONE
RS-232C LAN
5
3P073677-12P04.11.226:40PMページ6

Precautions
Internal Battery Enable(ON)/Disable(OFF)Switch
The intelligent Touch Controller is equipped with internal batteries in order to run the clock during
blackouts as well as to save data during blackouts when using the optional Power Proportional
Distribution. The batteries can be enabled and disabled using the switches shown in the figure below.
The clock and Power Proportional Distribution will not function properly when a blackout occurs
if this switch is turned to 「 OFF 」 .
The switches are turned to 「 ON 」 when the unit is installed. Do not touch them unless the power
has been turned off for a long time. (See the next page for details on what to do if the power has
been off for long periods of time.)
<Location and Setting of Switches>
Note
● Do not touch other switches.
● Avoid turning the switch ON and
OFF with excessive force; otherwise
such operation may lead to parts
damage and failure.
OFF
ON
is the location of the knob. RESET
As shown in the figure, set the battery switch on the left side of this controller to ÒOFFÓ (switch knob
upper side) or ÒONÓ (switch knob lower side), using a precision minus(-) screwdriver.
(Turning this switch OFF does not erase the settings for groups, zones or schedule.)
6
Maintenance
3P073677-12P04.11.226:40PMページ7

Maintenance
● When the surface of the LCD or the main unit of the intelligent Touch Controller is soiled, wipe the soil
off with a piece of cloth soaked in a diluted neutral detergent and wrung sufficiently.
Note
Do not use thinner, organic solvent, strongly acid solution, etc.
The print may fade or wear out and discolor.
Forced rubbing with hard cloth may cause damage to the liquid crystal display unit.
Remove stains, always using a soft waste cloth.
If the unit is stored with water droplets and stains sticking to the liquid crystal display unit, a blot may
be made and the coating may come off.
LCD Maintenance
When Leaving the Product Turned OFF for a Long Time
When you leave the intelligent Touch Controller turned OFF for a long time
(6 months or longer), turn the switch OFF to maintain the battery.
● The intelligent Touch Controller has a built-in battery for operating the clock in power failure.
The battery mentioned above is for power failure only and it may be completely discharged if no power
is provided for a long time.
(The capacity is worth about 2 years of in total if no power is supplied.)
● To use the intelligent Touch Controller again, turn the switch ON.
As shown in the figure, set the battery switch on the left side of this controller to ÒOFFÓ (switch knob
upper side) or ÒONÓ (switch knob lower side), using a precision minus(-) screwdriver.
(Turning this switch OFF does not erase the settings for groups, zones or schedule.)
[Setting the switch]
Note
● Do not touch other switches.
● Avoid turning the switch ON
and OFF with excessive force;
otherwise such operation may
lead to parts damage and failure.
If electric components in the intelligent Touch Controller are charged with static
electricity, it may cause failure.
Be sure to discharge the static electricity accumulated in your body before
attempting any operation.
To discharge yourself, touch a grounded metal object (control panel, etc.).
Caution
RESET
is the location of the knob.
OFF
ON
7
3P073677-12P04.11.226:40PMページ8

Troubleshooting
Before Having the Product Serviced
Item Description and Corrective Action
When Backlight Auto OFF is set for Backlight Setup of the
intelligent Touch Controller, the light goes out if the screen is
left untouched for a certain time.
Touch the screen with the pen provided. The display comes
back on.
The display of the intelligent
Touch Controller has gone out.
Backlight Auto OFF is a function to automatically turn the
backlight OFF if it is left untouched for a certain time.
If the display is 「 Set/Prop 」「 System Setup 」 etc., the light does
not go out automatically.
The backlight does not go out
when Backlight auto OFF is set.
Press and hold down the reset button on the left screen of the
intelligent Touch controller for 5 seconds.
Pressing this switch initialize the intelligent Touch Controller.
Pressing this switch does not erase the settings for groups,
zones or schedule.
The intelligent Touch
Controller cannot be operated
or monitoring is not available.
intelligent Touch Controller
Note
● Do not touch
other switches.
● Avoid turning
the switch ON
and OFF with
excessive force;
otherwise such
operation may
lead to parts
damage and
failure.
If electric components in the intelligent Touch Controller
are charged with static electricity, it may cause failure.
Be sure to discharge the static electricity accumulated in
your body before attempting any operation.
To discharge yourself, touch a grounded metal object
(control panel, etc.).
Caution
RESET
RESET
Press the RESET
button stamped
as ÒRESETÓ
thereunder with
something like a
thin shaft.
8
Maintenance
3P073677-12P04.11.226:40PMページ9

The intelligent Touch Controller is designed in such a way that
the buzzer sounds when any part of the screen is pressed. It
is normal.
Item Description and Corrective Action
On the Monitoring screen,
buzzer sounds when an area
not allocated for a button for
operation is pressed.
The buzzer sound may occasionally break up when the load
on the CPU is particularly large, but this is not a problem.
Something is wrong with the
buzzer sound (the sound
breaks up, etc.)
While the Monitoring screen is shown, the screen is updated
every 3 seconds to show the latest status of air conditioners.
The screen may look flickering when the update is made. It is
normal.
The screen flickers at a regular
interval.
Updating of the display may take some time depending on the
communication status with the air conditioners connected.
Update is completed in a few seconds.
Touching the screen of the
intelligent Touch Controller does
not change the display soon.
There may be found some dots that are never illuminated or
always illuminated on a certain part of the LCD of the
intelligent Touch Controller. It is normal.
The LCD may inherently generate unevenness due to change
of temperature, which is normal.
Some dots of LCD are never
illuminated.
When adding an air conditioner to be connected to the
intelligent Touch Controller, trial running of the intelligent
Touch Controller, as well as of the air conditioner, is required.
When trial running of the intelligent Touch Controller has
not been performed, contact our representative.
An air conditioner to be connected
to the intelligent Touch Controller
has been added but the added air
conditioner cannot be monitored
on the Monitoring screen of the
intelligent Touch Controller.
9
3P073677-12P04.11.226:40PMページ10